P200 Manual V1.0 2021.02 www.toolkitrc.com ToolkitRC Technology (Shenzhen) Co.
Introduction Thank you for purchasing the M7 model tool chain product, please read this manual carefully before using it. Key Points Tips Important Information Further information To ensure you have the best experience with this product please scan the QR code below to stay up to date with news, information and firmware updates for your charger. Or visit www.toolkitrc.com.
Safety 1. P200 allows the input voltage of DC 7-28V or AC 100-240V to ensure that the power supply voltage conforms to the power supply. Pay attention to the positive and negative polarity of the power supply when connecting. 2. Do not use this product in the environment of heat source, humidity, flammable and explosive gas. 3. Please use this product when someone is guarded to prevent accidents. 4. When not using this product, please unplug the input power in time. 5.
Contents Introduction.......................................................... 2 Key Points............................................................. 2 Further information............................................. 2 Safety......................................................................3 Contents................................................................4 P200 Layout..........................................................6 Quick start.......................................................
Product description P200 is a mini desktop adjustable power supply, with AC or DC two input modes, built-in 100W GaN AC power supply, IPS wide-angle display screen records and curve display voltage and current, and other features. Built-in gallium nitride (GaN) small AC power supply. AC/DC two input modes. The conversion efficiency is as high as 95%. AC input: the full output power is up to 100W. DC input: the full output power is up to 200W. TYPE-C MAX output 65W.
P200 Layout Display A Wheel (Current adjustment) Power button Output main port Type-C V Wheel fast charge output Front Front (Voltage adjustment) AC Input port Cooling fan DC Input port Back 6 AC power switch @ToolkiRC 2021
Quick start 1. Connect the 7-28V DC power supply to [DC input port] on the back of the P200 or AC 100-240V to [AC power port], and turn on [AC power switch]. 2. Press the front [Power button] once, the display shows the boot logo and stays for 2 seconds. 3. At the same time, it is accompanied by do-re-mi boot sound. 4. After the boot is completed, the screen enters the main interface and displays as follows:： 5. Fluctuating [V dial], set the voltage to be output. 6.
10. Long press [A dial], the accumulated capacity and time information will be cleared. =================================== Warning: 1. Inputting too high DC voltage may damage the product. 2. Do not connect to the input terminal if the voltage value is not marked. 3. When the output is connected to the lithium battery for charging, pay attention to the full voltage of the battery.
Output settings and display instructions Turn the [V dial] on the main interface to set the voltage to follow the adjustment. The step voltage can be adjusted in the system menu. Turn the [V dial] to set the maximum constant current value that requires constant current. After setting the required voltage and current, short press [V dial] once to output the set voltage from the main port.
Curve area: Real-time recording of the voltage and current of the output main port. 000:59: The accumulation of the output time of the main port. 50.0W: The current output power of the main port. 88Wh: Main port output power statistics. 3.00A: The real-time current value output by the main port. 12.0V: The real-time voltage value output by the main port. 10.0A: The set maximum constant current value. 12.0V: The set maximum constant voltage value. 2.
059:59: Output the accumulated time. 8888Wh: The accumulated value of output electric energy. PD3.0: The current device fast charging protocol. ON: TYPE-C output status. =================================== Tips: 1. Long press [A dial] once to clear the accumulated value. 2. Connect to the USB-C charging device, and the USB port will output the corresponding voltage and current according to the protocol.
System settings After selecting and long-pressing [V dial] on the main interface, you will enter the system setting interface, as shown in the figure below: Back: Back to the main interface. Step voltage: The step value of adding or subtracting the output voltage by turning the voltage dial, the setting range is 0.05-0.5V. Step current: The current dial turns the step value of the output current plus or minus one grid, the setting range is 0.05-0.5A. Curve Time: Record the curve period, you can set 0.
Backlight: Display backlight brightness value, can be set to 1-10 levels. Beep: The tone of the buzzer, which can be set to off. Language: System display language. You can choose English, Chinese, etc. Theme style: Two themes of bright and dark colors can be selected. Factor settings: Restore all setting items to factory values. ID：An independent ID for each device.
other functions 1. Firmware upgrade After connecting the P200 to the computer with the USB data cable in the box, the computer will recognize a U disk named Toolkit. Download the upgrade file app.upg on the official website to overwrite the files in the U disk to upgrade the firmware. 2. Fan level When the internal temperature of the device exceeds 45°C, the fan turns on half-speed air volume to reduce noise.
Specifications Input voltage AC 100-240V@MAX 100W DC 7-28V@MAX 10A 200W 1.0-10.0A @MAX AC 100W / DC Main output 200W 1.0-30.0V @MAX AC 100W / DC 200W Electric TYPE-C output TYPE-C protocol Protection response Interface Display 5.0-20.0V @MAX 65W PD3.0/PD2.0/PPS/QC4/QC3.0/QC2.0/ AFC/FCP/SCP/PE2.0/PE1.1/SFCP/VOO C <1ms (Short circuit, over current, over voltage) Adjustment period 8ms Main port 4.0mm Banana female USB TYPE-C Fast charge Firmware upgrade LCD IPS 1.
