User's Manual

Release button
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
guide, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult a service representative for help.
Properly shielded and grounded cables and connectors must be used in
order to comply with FCC emission limits. LifeWorks is not responsible
for any radio or television interference caused by using other than
recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications
could void the user’s authority to operate the equipment.
Responsible party:
LifeWorks Technology Group LLC
530 7th Ave., New York, NY 10018
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
CAR MOUNT KIT
WIRELESS CHARGING
BRQICM302
Product Description Product Description
Product Specs
COMPATIBILITY: Compatible with all decives with QI charging
INPUT: 5V=2A/9V=1.67A
OUTPUT: 5V=1.5A/9V=1.2A
CHARGING EFFICIENCY: 75%
Installation Steps:
1. To attach phone cradle to air vent mount or dashboard
mount - (follow steps in image below):
2. Put lock knut over ball joint
3. Gently slip O-Ring over ball joint
4. Put ball joint into back space of phone cradle
5. Screw lock knut onto phone cradle
Power:
1. To use wireless charging and smart grip sensor you must
connect the wireless charger phone cradle to a power source
with included power cable.
2. Must use Qualcomm quick charge adaptor for fast wireless
charging.
To Use:
1. Once the power cord is
connected, check the LED
indicator.
• Blue light= normal active status
• Red light flashes= not working
• No light= no power
2. Place phone in front of
sensor- phone grip will
automatically open wide
3. Place phone into grip- grip will
automatically close
Remove Smartphone:
1. Touch the release button
on the side
2. Grip automatically opens
and releases phone
3. Take phone out
Operation
Operation
Safety Warnings and LegalSafety Warnings and Troubleshooting
1
4 5
2 3
FRONT BACK
Warning Improper setup, use and care of this product can
increase the risk of serious injury death or devic damage.
Read and keep this guide and all other printed guides for future
reference. For updated guides or replacements go to
golifeworks.com
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 0cm between the radiator and
your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Do Not Attempt Repairs. Do not attempt to take apart, open,
repair, service or modify the device(s). Doing so may
risk electric electric shock or other hazard. Evidence of any attempt
to open or modify the device, including any peeling, puncture or
removal of labels, will void the Limited Lifetime Warranty.
Lock Knut
Expanding
Arms
LED Indicator
Wireless
Charging
Pad
O-Ring
Lock Knut
Telescoping Arm
Adjust Knob
Adjust Knob 2
Suction Cup Lever
Air Vent
Mount
Vent Release
Ball Joint
Grip Release
Button
Smart Sensor
Phone Cradle
Power cord
Port (behind)
Gel Suction
Cup
1
2
3
4
Follow the arrows to assemble parts
Insert power cord into back port
Adjust the screw cap to the best angle
for viewing
Attention
1. Please keep charger away from water or other liquid
2. If you need to clean the charger, please make sure it is
not connected to the poewr supply
3. Working temperature: -20°~45°C (-4°~113°F)
When the LED light flashes during the wireless charging,
which indicates a charging failure
The following situations can cause failures like high
temperature, slow charging and no charging
1. The adapter is not up to standard
2. The charging cable is not up to standard
3. The phone case is too thick (recommended phone case
thickness within 2mm
4. The phone is not placed at the center of the wireless
charger
5. There is metal/magnet on the back of cell phone or
phone case
6. Cell phones do not support QI wireless charge function
Customer Service: 877-5430-3540
www.brookstone.com
The BROOKSTONE® trademarks, names and logos are owned by BKST Brand
Holdings LLC. 2019 ©. All rights reserved, manufactured, marketed, and
distributed by Lifeworks Technology Group LLC., used under license.
Made in China
What is covered under the Limited Lifetime Warranty?
Lifeworks Technology warrants that this product will be free
from defects in workmanship and materials under normal use
("Limited Lifetime Warranty"). In a case where the product is
determined to be "defective", we will repair the product free of
charge. If we cannot repair the product, we will replace it for
you free of charge.
How long am I covered?
You are covered for the Lifetime of the product which means
that as long as we are still
manufacturing and selling the product we cover you under
warranty.
What is not covered under the Limited Lifetime Warranty?
1. Normal wear and tear of product use.
2. Misuse, lack of care, mishandling, accidental
damage, abuse or other abnormal use.
3. Use of the product other than for its intended
purpose.
4. Damage caused by improper or unauthorized repair
or maintenance.
5. Product that has been modified or altered.
6. Any product that is not manufactured by Lifeworks
(including, without limitation, any non-Lifeworks
product that is used in connection with the product).
Limited Lifetime Warranty
FCC Warning:
This product is suitable for any car.
Installation environment: Window or Dash Mount
Driver Seat
Knee: 29cm, Leg: 36cm, Body: 74cm, Hand: 45cm, Arm: 62cm, Head: 114cm
Passenger Seat - Front
Knee: 28cm, Leg: 35cm, Body: 75cm, Hand: 46cm, Arm: 61cm, Head: 115cm
C
M
Y
CM
MY
CY
CMY
K
BRQICM302B-JP-BB user manual.pdf 1 9/9/19 9:45 AM