:. + :.
For more information,please browse https://www.tobbi.
Structure Chart To reduce the risk of injury, adult supervision is required.
Spare Parts Product Figure 12 M10*95 Screw 13 M10 Gasket 14 M12 Gasket 15 M10 Gasket 6)9 6)9 6)9 16M4*14 Screw 17M5*30 Screw 18 M5*30 Screw 19 6)9 3 4 Cotter Pin 9 10 1 6)9 20 Charger 6) 9+: 9+: 21 Spanner 6)9 6 9 2 10 8 6)9 5 11 8 7 10 5 6 10
Assembly Steps Assembly Steps /TYZGRR ZNK 8KGX 1.Insert the rear axle(11) into the motor hole,and pass through the opposite side of the body,so that both sides of the rear axle are even. 11 /TYZGRR 9ZKKXOTM (XGIQKZ 1. Install the front wheel iron(7) from the bottom to the top on the front steering bracket. 2. Insert the long M10*95 screw(12) through the hole of steering bracket. 3. Screw the nuts (M10 nut)(13) on both sides to fix it. 4.Repeat the above steps for the other rear wheel.
Assembly Steps Assembly Steps Install the Front Wheel 1. Install a M12 gasket(14) and slide it into the front axle. 2. Install the front wheel(8) on the front axle. 3. Install another M12 gasket(14) and slide it into the front wheel. 4. Tighten the M10 nut(13) with a wrench(21). 5. Cover the small wheel hub(10) and press it. Repeat the above steps for the other rear wheel. Install the Steering Connecting 1.
Assembly Steps Assembly Steps Install the Steering Rod 1. Pass the steering axle(6) through the steering hole and align it through the connecting rod, 2. Fix it on the front steering shaft with M10 Gasket(15) and cotter pin(19) as shown in the figure. Install the Steering Wheel Connecting Rod 1.Connect the terminal at the bottom of Part No. 2 to the terminal on the chassis. 2.Install the steering wheel(4) connecting rod and fasten the M5 nut with a short 5*30MM screw(18). 3.
Assembly Steps Assembly Steps Install the Seat 1. Install the seat(3) on the body and fix it with 4 M4*14 screws(16). Fixed Base 1.Use a screwdriver to tighten 2 M4x14 screws(16) at the pre-drilled screw holes on both sides of the armrest to fix the base.
Funciton Diagram and Operation Method Assembly Steps )UTTKIZ ZNK 6U]KX 9[VVR_ 1. Use a screwdriver to remove the rear cover according to the position shown in the figure, and then connect the two connection terminals below. 2. Cover the rear cover tightly. Change the music Klaxon Pedal High speed Forward Low speed Stop Power switch Backward Push down on the pedal to drive forward/backward. Release the pedal to slow down and stop.
Funciton Diagram and Operation Method Charge Mode Battery indicator Turn up the volume Turn down the volume Pause key music Klaxon · The charging outlet is located under the seat. Plug one end of the part 11 charger into a charging outlet and the other end into a wall outlet. · Charge the battery for at least 12 hours before initial use. · On average, you will need to charge the battery between 10 and 12 hours. · Do not charge the battery for more than 20 hours.
Disclaimer Simple Trouble Shooting ͓=K ]ORR TUZ ZGQK XKYVUTYOHOROZ_ OL _U[ INGTMK ZNK IOXI[OZ YZX[IZ[XK UX L[TIZOUT UL ZNK \KNOIRK ͓:NK JOGMXGSY OT ZNOY SGT[GR GXK LUX YNU]OTM ZNK UVKXGZOTM SKZNUJ GTJ ZNK YZX[IZ[XK UL ZNK \KNOIRK /L ZNKXK GXK YUSK JOLLKXKTIKY HKZ]KKT ZNK VOIZ[XKY GTJ ZNK XKGR \KNOIRK VRKGYK XKLKX ZU ZNK XKGR \KNOIRK ͓/T UXJKX ZU OSVXU\K ZNK W[GROZ_ ]K SG_ INGTMK YUSK VGXZY UL ZNK YZX[IZ[XK UX OZY GVVKGXGTIK ]OZNU[Z TUZOIK OT GJ\GTIK NUVK