Trantec S5 Wireless Microphone Series Trantec S5 Wireless Microphone Series Q U I C K I N S TA L L AT I O N G U I D E
CONTENTS Page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
SAFETY Our aim is to supply you with a product that provides you with countless hours of trouble free use. In order to achieve these goals we recommend the following: • Keep the system away from direct sources of heat e.g. central heating radiators, heaters and direct sunlight. • Do not expose the unit to an environment where it could be splashed with liquids as this may result in fire or electric shocks.
RECEIVER SET-UP DC inlet 1/4” jack output DC strain relief Mic/Line switch USB port XLR output Rear View Diversity switch A/B indicators LCD Infra-red port Jog wheel Mute indicator Power switch indicator Headphone output Front View 1. Attach the supplied antennae (2) to the rear panel BNC antenna connectors as shown in above illustration. 2. Connect the AC/DC adaptor into the DC inlet as marked on the rear panel using the attached cable strain relief.
RECEIVER FREQUENCY SELECTION 5. Frequency selection options • To change selected channel in BANK1: Press “Jog-wheel” for 3 secs and enter the MAIN MENU. Press FREQ SELECT and go to BANK setting, then select BANK1 and rotate jog wheel to select new channel, finally press to ACCEPT to select new frequency. See attached frequency table. • To change selected Bank: Press “Jog-wheel” for 3 secs and enter the MAIN MENU.
TRANSMITTER SET-UP HANDHELD End cap Sleeve Power ‘On’ Position Infra-red port Up/Down Grille Frequency Battery indicator 1. Undo handheld sleeve by unscrewing the end cap anti-clockwise and then gently sliding the sleeve to expose the LCD and Battery compartment. Place alkaline “AA” cell into battery compartment observing the correct polarity. 2. Slide the On-Off switch to the “On” position and observe the display is on and the battery LED located in the end cap is illuminated.
TRANSMITTER SET-UP BELTPACK 1. Insert battery into compartment by sliding end cap forward and up. Ensure battery is inserted with the correct polarity as shown. Antenna 2. Screw antenna into antenna socket as illustrated. 3. Plug Lavalier mic into Mini-XLR socket. Lavalier mic Clip 4. Place on-off switch to “On” position and observe the display is on and the battery LED is illuminated. Check display indicates same channel as receiver. 5.
OPERATING HINTS To maximise operating performance Trantec recommends the following: • Ensure good line of sight between receiver antenna and transmitter, avoid obstructions e.g. concrete walls and metal structures. • Ensure the receiver antenna is at least 3m (10 feet) away from the transmitters at all times. • Always ensure transmitters are separated by at least 20cm. • Never position the transmitter antenna directly against the body or the hand. This will reduce the operating range.
S5 SERIES RACK MOUNT KIT The rackmounting kit is supplied as standard with S5.5 systems, or is available as an accessory for S5.3 systems. POWER POWER RF A RF B uV dB 1 2 4 8 16 -36 -30 -24 -18 -12 -9 -3 0 RF A RF B 30 60 125 250 500 +3 +6 uV dB 1 2 4 8 16 30 60 125 250 500 -36 -30 -24 -18 -12 -9 -3 0 +3 +6 19” Rack 2 x S5 series Receivers 2.
TECHNICAL SPECIFICATIONS Overall System Frequency Bands available: D3 830-865MHz B1 722-752MHz E1 668-698MHz G2 606-622MHz (S5.3 only) D1 863-865MHz C1 794-830MHz B2 740-752MHz F1 636-668MHz RF Switching BW: RF grid spacing: RF Bandwidth: AF Frequency response: AF Distortion: AF Dynamic range : AF Noise reduction: Temperature range : 36MHz typical 25kHz < 200kHz 60Hz – 20kHz < 0.
CE DECLARATION OF CONFORMITY 0891 ! This equipment is in compliance with the essential requirements and other relevant provisions of Directives 1999/5/EC, 89/336/EC or 73/23/EC. IMPORTANT NOTICE. Before using this wireless microphone system please observe the requirements of each country with respect to frequency allocations and individual licensing requirements.
URL: http://www.toa.