GRADE 1 CYLINDRICAL ELECTRONIC LOCK USER MANUAL
Table of Contents 1. Introduction ............................................................................................................................ 2 2. Compatible cards and phones ............................................................................................. 2 Cards ........................................................................................................................................ 2 Phones ........................................................................
1. Introduction A1 is a smart lock with Bluetooth, HID LF card capabilities. 2. Compatible cards and phones Cards • HID LF Card 125kHz needs to cover the following as below. - HID PROXCARD Ⅱ : 1326 thick card - HID ISOCARD Ⅱ - HID DUOCARD Ⅱ :1336 thin magnetic stripe card - HID MICROPROX HID PROXKEY Ⅱ : 1386 thin card :1391 label card :1346 keyfob Phones • • iPhone 4S or above with iOS 8.0 or above Android 4.3 or above with Bluetooth Low Energy capability. 3.
. Phone Operations A compatible phone with App installed can be used as Admin of Locks. Management tasks can be performed by Admin in the App. An Admin can manage multiple Locks, but one Lock can only have one Admin at a time. Other phones can be Clients of the Lock. Pairing to Become the Admin 1. In K3 Connect, press the “+” on the top-right corner of the Locks page 2. Fill-in the DIN (A1) and your selected Lock name, then confirm and put the phone close to the Lock (within 1 meter) 3.
- Restore Set Access Right (All Time/One Time/By Duration) Set Client Nick-names View Audit Trail Check Lock Battery status Update Lock Firmware Gateway Management 5. Card Operations Card Unlocking Put the card in front of the sensing area, and wait until LED flash and beep heard. 6.
8.
Unlocking, or Sync) but other function of Lock is still working 2. If still not working, turn-off Bluetooth function on the phone and turn-on again, then try again If still not working, reboot the phone and try again 3. 11.
Pair Lock Step 1: Click on “+” icon at right top corner to add lock Step 2: Enter Lock DIN: A1 Step 3: Assign a name, such as front door. Click on “√” at right top corner to add lock. App will inform to make the lock enter the setup mode. Step 4: Locate your A1's "Reset" button.
Step 5: you will hear 2 long and 2 short beeps to know the pairing success Add phone users Step 1: Click “clients” . Tap” +” icon Step 2:Click on “type” and select “ Phone” Step 3: Entering “client’s email”. Click on “>” at right top corner to add lock.
Step 6: Click on “lock” page. Click on “Sync” to synchronize your lock Add card user Step 1: Click “clients” and tap” +” icon Step 2: Click on “type” and select “ Card” Step 3: Select the lock that you want to add Card users Step 4: Click on “Setup Lock” and you will hear a long beep. Step 5: make card to tap the HID sensor in front of the lock. When the card is successful to be added, you will hear a long beep.
Delete user (Phone or Card) Step 1: Click “clients” Step 2: Choose the card and swipe bar to left. Click “Delete” Step 3: Click “Confirm” Step 4: Click “Close” Step 5: Go to lock page.
Lock logs Step 1: Choose the lock and swipe the bar to left. Step 2: Click Logs and you will show all activities of the lock.
Lock information & Parameters Choose the lock and swipe the bar to left. Click info. Lock Down: Except for administrators, other permissions are forbidden to unlock the lock. Passage Mode: Keep the lock unlocked Auto Relock Delay: Set relock time from 2s to 99s. Daylight Saving: open or close daylight saving. Mute: turn off all sounds. Setting User Info: - User Name: change user name - Change password: change new password - Change user name and password: click setting page and access in to user ifno.
Gateway Management Set up: To use Gateway, you need to be the Admin of at least one compatible Locks. See the User Manual of the compatible Locks to learn how to become the Admin.
Release Gateway: Step 1: Click “Clock” Page Step 2: Swipe bar to left and click info Step 3: Click “Gateway Management” Step 4: Click “Release Gateway” Step 5: Click “Yes” 14
* If you don’t see the “Gateway Management” option in the app, make sure the K3 Connect app and Lock firmware is updated to the latest version available 12. FCC/IC Statements Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
2. This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
