FLOOR ONE S5 COMBO SERIES ES Smart Cordless Vacuum & Washer Instruction Manual Manual De Uso Mode D’emploi *Actual product may differ from illustration. TINECO IS HERE TO HELP. We’ll get back to you within 1 business day. www.tineco.com 1-855-292-8864 Mon. - Fri.
Important Safety Instructions............................................................... 2 Overview................................................................................................ 6 Accessories............................................................................................ 8 Assembly ............................................................................................... 9 Operation .......................................................................................
Important Safety Instructions SAVE THESE INSTRUCTIONS Household use only. EN When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING – To reduce the risk of fire, electric shock, or injury: 1.
3 EN 16. Recharge only with the charger specified by Tineco. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 17. Use appliances only with specifically designated Tineco battery packs. Use of any other battery packs may create a risk of injury and fire. 18. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water.
Range of Usage 1. The cordless hard floor cleaner is to be used on indoor hard floors, such as vinyl, tile, sealed wood, etc. Use on a rough surface may not get the best performance. 2. Keep your appliance away from heat sources, such as fireplace or heater, to avoid casing deformation. 3. Do not use to pick up flammable or combustible liquids, ultrafine particles, sharp objects, hazardous material, chemicals or anything that is burning or smoking, as described above. EN About Cleaning Solution 1.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Overview A P B Q C J V S W EN R K D L E M T F X N G U H I O A. Self-cleaning Button N. Clean Water Tank (CWT) B. AUTO/MAX Mode O. Brush Roller C. Power On/Off P. Cleaning Tool D. Digital Display Q. Dry Filter & Holder E. Main Body R. Deodorizing & Cleaning Solution F. Dirty Water Tank Release S. Accessory Holder G. Dirty Water Tank Handle T. Adaptor H. Dirty Water Tank (DWT) U. Charging Base I. Brush Roller Cover V. Crevice Tool J. Tube W. 2-in-1 Dusting Brush K.
EN Digital Display A B C D E F G H I J K L M N A. Dirt Monitoring Loop (Blue to red according to the dirt amount) H. Brush Roller Tangled B. WiFi Indicator J. MAX Mode in Hand Vac C. AUTO Mode K. Dust Sensor Malfunction D. DWT Full L. ECO Mode in Hand Vac E. MAX Mode M. Battery Indicator F. Floor Washer N. Self-cleaning Icon I. Hand Vac G.
Accessories Note: Accessories may vary between markets. If you require more accessories, please go to www.tineco.com or store.tineco.com. EN Deodorizing & Cleaning Solution Removes dirt, grime, grease and tough stains from most types of hard surfaces, like tile, marble, sealed hardwood floors, and more. Always use Tineco solution in your appliance. Add one bottle cap of solution to each full tank of clean water. Brush Roller Soft roller head with bristles can be used to vacuum and wash at the same time.
Assembly How to Assemble/Disassemble Note: EN For water tank and brush assembly, please refer to “Operation” and “Maintenance”. click To assemble, install the main body and handle into the appliance until you hear a click. In the event that the handle need to be disassembled, first remove the main body. Press the spring to release the handle with a tool (like a screwdriver) and lift the released handle from the appliance.
Operation Preparing for Use Before first use, please charge the appliance for 3~4 hours (refer to “Charging Instructions” for details). * Based on results from Tineco lab tests. Lab temperature 39.2°F (4°C) ~ 104°F (40°C). Tips: EN • Solution mode/ Water Only mode: Appliance starts with Solution mode by default. Power on while the appliance is upright, long-press for 3s to switch between the two modes.
Filling Clean Water Tank Press the Clean Water Tank release button to remove it from the appliance. Open the tank cap, and fill with tap water to the Max line. When deep cleaning is necessary, add one bottle cap of solution to the CWT and tightly close the cap. Note: Only use water under 140°F/60°C. DO NOT USE HOT WATER. ② click ① Place the tank back into the appliance. You should hear a “Click” if done correctly.
Cleaning Mode Selection AUTO Mode EN • In AUTO mode, the iLoop™ sensor automatically detects how dirty the floor is and applies the appropriate amount of detergent and suction power. • A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is detected. This mode automatically provides the best cleaning solution. MAX Mode • In AUTO mode, press the button to enter MAX mode.
Usage of Hand Vac EN or Install the dustbin to the main body properly and it clicks into place. Attach the accessory tool onto the dustbin, it will click into position when correctly fitted. • Press the release button to remove the dustbin, pull out the mesh filter as above and empty the contents. • Press the HEPA lock button to take out the HEPA and sponge filter, clean both parts with the cleaning tool. Note: • Clean the dustbin and filters after each use.
Runtime • The runtime for the Floor Washer is about 15~20 minutes. • The runtime for the Hand Vac is about 25~50 minutes. • Estimated runtime data was obtained by a Tineco Laboratory. Charging Time EN • A full charge takes approximately 3~4 hours. • Estimated data was obtained by a Tineco Laboratory using ambient temperatures between 39.2°F (4°C) to 104°F (40°C). Indicator When in Use Battery level > 10%: battery indicator will be illuminated. Battery level ≤ 10%: battery indicator will be blinking.
Blinking: WiFi is connecting. Off: WiFi is not connected, please connect to the network. EN Indicator blinking: appliance is in need of self-cleaning. During Charging Tineco indicator: breathing. Fully Charged In 5 minutes: Tineco indicator illuminated. After 5 minutes: all indicator lights turn off. App All the functions can be performed using the Tineco app. Download the Tineco app from the App Store, Google Play and Tineco Official Site.
EN Voice Prompt (Contents may vary, please in kind prevail.
Maintenance Note: • For optimal performance and to prevent odors, always clean and dry DWT, floater, filters, brush roller, brush roller cover completely after each use. • Please make sure each part is installed correctly or the appliance may not work properly. • After maintenance, place the appliance on the charging base vertically. Do not expose the appliance to direct sunlight, and store it indoors in a dry place. EN Main Body To reduce the risk of injury, switch off before performing maintenance.
Dirty Water Tank EN click • When dirty water reaches the Max line, the appliance will stop working and show a reminder on the display and play a voice prompt. • Pull up the tank lid to empty the DWT. Use the cleaning tool to remove remaining debris. Rinse the inside of the DWT and place back into the appliance. Dirty Water Tank Lid If the Dirty Water Tank lid and the filter inside have been blocked, remove the tank lid and the filter, rinse both parts with water.
Brush Roller Self-cleaning Note: • Ensure the charging base is plugged in. • Before self-cleaning cycle, please clean the DWT and ensure the water level in the CWT exceeds 40%. Brush Roller Cover ② ① Squeeze latches on the cover and pull upward to remove. Rinse with water. click When replacing, always latch the brush cover into place to avoid leakage. 19 EN 1. Place the appliance on the charging base after use, the sensor will auto-detect the level of dirt. 2.
EN Brush Roller Remove the brush roller by grabbing the brush roller tab and pulling out. Using the cleaning tool, remove the hair and debris wrapped around the roller and rinse with water. Replace the brush roller back into the accessory holder, and allow it to dry completely before reinstalling. Remove hair and debris from the brush roller chamber and the opening with a tissue or a damp cloth.
Specifications Product FLOOR ONE S5 COMBO SERIES AC Input 100~240V Voltage 21.6V Rated Power 190W Running Time Floor Washer: 15~20 mins / Hand Vac: 25~50 mins Charging Time 3~4 hrs Water Flow Rate 30~100ml/min CWT Capacity ~0.5L DWT Capacity ~0.45L Waterproof IPX4 EN 2500mAh Lion Disposal • The battery contains materials that are harmful to the environment and must be removed from the appliance before it is discarded. • When removing the battery, the appliance must be powered off.
Troubleshooting Problem Solution Auto protection for overheating Restart after cooling down Contact piece on the main body is dusty Clean the contact piece with a dry cloth Weak suction The dry filter is not installed, or the dry filter is dirty Install the dry filter or clean and allow it to dry completely Brush roller tangled indicator blinking Voice prompt: 1. Please clean the brush roller 2. Please install the brush roller correctly 1. The brush roller is blocked 1. Remove blockages 2.
Warranty 2-YEAR LIMITED WARRANTY • Only applies to purchases made from authorized retailers of Tineco. • Is subject to the adherence of the requirements outlined in this instruction manual, and is subject to further conditions outlined below. • Your Tineco appliance has a 2-year warranty against original defects in material and workmanship, when used for private household purposes in accordance with the Tineco Instruction Manual.
WARRANTY LIMITATIONS EN • Any implied warranties relating to your appliance including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty. • Warranty coverage applies to the original owner and to the original battery only and is not transferable. • This limited warranty gives you specific legal rights. You may also have other rights which vary by region.
SOMMAIRE Consignes de sécurité importantes .................................................. 51 Description .......................................................................................... 56 FR Accessoires.......................................................................................... 58 Assemblage ........................................................................................ 59 Fonctionnement .................................................................................
Consignes de sécurité importantes CONSERVEZ CES INSTRUCTIONS Usage domestique exclusivement. Lorsque vous utilisez un appareil électrique, veuillez respecter les précautions de sécurité élémentaires, notamment celles indiquées ci-dessous : LISEZ TOUTES LES INSTRUCTIONS AVANT L’UTILISATION (DE CET APPAREIL). Le non-respect des consignes de sécurité et des instructions peut provoquer une décharge électrique, un incendie et/ou des blessures graves. électrique ou de blessures corporelles : 1.
FR 12. Ne passez en aucun cas l’aspirateur sur des objets brûlants ou incandescents, comme des cigarettes, des allumettes ou des cendres chaudes. 13. Ne faites pas fonctionner cet appareil sans le filtre. 14. Évitez la mise en marche accidentelle. Vérifiez que l’interrupteur marche/arrêt est en position d’arrêt avant de saisir l’appareil ou de le porter.
FR 28. N’utilisez pas l’appareil pour ramasser des matières dangereuses et des produits chimiques, tels que des solvants, des produits de nettoyage pour vidange, des acides forts ou des alcalis puissants. 29. Cessez immédiatement d’utiliser l’appareil en cas de surchauffe, de bruits inhabituels, de mauvaises odeurs, de faible aspiration ou de fuite d’électricité. 30. Éteignez le nettoyeur et débranchez-le de la prise électrique avant de le ranger pour une longue période. 31.
À propos de l’appareil 1. Ne modifiez pas et n’essayez pas de réparer l’appareil sauf comme indiqué dans les instructions de fonctionnement et de nettoyage. 2. Chargez l’appareil avec l’adaptateur Tineco. Tension d’entrée : 100 - 240 V c.a. Les tensions élevées et basses peuvent endommager l’adaptateur, l’appareil ou même entraîner un danger pour l’utilisateur. 3. Soyez particulièrement vigilant(e) en passant l’aspirateur dans les escaliers. 4.
Cet équipement génère, utilise et peut émettre de l’énergie par radiofréquence. S’il n’est pas installé et utilisé conformément aux instructions, il peut provoquer des interférences nuisibles aux communications radio. Toutefois, il n’est pas garanti que des interférences ne se produiront pas dans une installation particulière.
Description A P B Q C J R V S W K D L FR E M T F X N G U H I O A. Bouton de nettoyage automatique N. Réservoir d’eau propre (REP) B. Mode AUTO/MAX O. Rouleau brosse C. Marche/arrêt P. Outil de nettoyage D. Affichage numérique Q. Filtre sec et support E. Corps principal R. Solution de nettoyage et de désodorisation F. Déverrouillage du réservoir d’eau sale S. Porte-accessoires G. Poignée du réservoir d’eau sale T. Adaptateur H. Réservoir d’eau sale (RES) U.
FR Affichage numérique A B C D E F G H I J K L M N H. Rouleau brosse emmêlé A. Boucle de surveillance de poussières (De rouge à bleu selon la quantité de saleté) I. Aspirateur à main J. Mode MAX dans l’aspirateur à main B. Indicateur Wi-Fi K. Capteur à poussières défectueux C. Mode AUTO D. Réservoir d’eau sale plein E. Mode MAX L. Mode ECO dans l’aspirateur à main F. Laveuse de parquet M. Indicateur de batterie G. REP vide N.
Accessoires Remarque : Les accessoires peuvent varier selon les marchés. Si vous avez besoin de plus d’accessoires, veuillez aller sur le site www.tineco.com ou store.tineco.com. Solution de nettoyage et de désodorisation Élimine la saleté, la graisse et les taches tenaces de la plupart des types de surfaces dures, comme le carrelage, le marbre, le parquet, etc. Utilisez toujours la solution Tineco avec votre appareil. Ajouter un bouchon de flacon de solution dans le réservoir d’eau propre.
Assemblage Comment assembler/désassembler l’appareil Remarque : Pour l’ensemble constitué du réservoir d’eau et de la brosse, reportez-vous aux sections « Fonctionnement » et « Entretien ». FR clic Pour monter, installez le corps principal et la poignée dans l’appareil jusqu’à entendre un clic. Dans le cas où la poignée doit être démontée, retirez d’abord le corps principal.
Fonctionnement Préparation à l’utilisation Avant la première utilisation, veuillez charger l’appareil pendant 3 à 4 heures (reportez-vous à la section « Instructions de chargement » pour plus de détails). * Basé sur les résultats des tests de laboratoire Tineco. Température de laboratoire 4 °C à 40 °C. FR Conseils : • Mode Solution/Mode Eau seulement : L’appareil démarre en mode Solution par défaut.
Remplissage du réservoir d’eau propre MAX Appuyez sur le bouton de déverrouillage du réservoir d’eau propre pour le retirer de l’appareil. Ouvrez le bouchon du réservoir et remplissezle d’eau du robinet jusqu’à la ligne Max. Si un nettoyage en profondeur est nécessaire, ajoutez un bouchon de flacon de solution dans le REP et fermez fermement le bouchon. Remarque : Utilisez uniquement de l’eau dont la température est inférieure à 60 °C. N’UTILISEZ PAS D’EAU CHAUDE.