CARPET ONE Smart Carpet Washer Instruction Manual Manual De Uso Mode D’emploi *Actual product may differ from illustration. TINECO IS HERE TO HELP. We’ll get back to you within 1 business day. www.tineco.com 1-855-292-8864 Mon. - Fri.
Important Safety Instructions................................................................ 2 Overview................................................................................................. 7 Accessories............................................................................................ 9 Assembly.............................................................................................. 10 Operation.......................................................................................
Important Safety Instructions SAVE THESE INSTRUCTIONS Household use only. EN When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING – To reduce the risk of fire, electric shock, or injury: 1.
20. TO REDUCE THE RISK OF ELECTRIC SHOCK – UNPLUG BEFORE CLEANING OR SERVICING. UNPLUG BEFORE CONNECTING HOSE. 21. Always turn off this appliance before connecting or disconnecting the motorized nozzle. 22. Turn off all controls before unplugging. 23. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 24. Do not use to pick up ultrafine particles, such as lime, cement, sawdust, gypsum powder, or ashes. 25.
Range of Usage 1. The Carpet washer is to be used on carpets, such as level loop, etc. 2. Keep your appliance away from heat sources, such as fireplace or heater, to avoid casing deformation. 3. Do not use to pick up flammable or combustible liquids, ultrafine particles, sharp objects, hazardous material, chemicals or anything that is burning or smoking, as described above. EN About Cleaning Fluid/Solution 1. A large amount of cleaning solution entering into the motor may cause damage to the appliance.
3. This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that looks like the plug illustrated in sketch A in Figure 20. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adaptor should be used with this appliance. TINECO / CARPET ONE SERIES This appliance complies with part 15 of the FCC Rules.
IC Note EN This appliance contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this appliance may not cause interference. (2) t his appliance must accept any interference, including interference that may cause undesired operation of the appliance. - This Class B digital apparatus complies with Canadian ICES-003.
Overview A G H S T J B K C U L D M N E V O P Q F R A. Dry Mode L. Clean Water Tank (CWT) B. WiFi/Mute Button M. Dirty Water Tank Handle C. Back Carry Handle N. Dirty Water Tank (DWT) D. Cord Wrap O. Brush Roller Cover Release Button E. Dirty Water Tank Release Pedal P. Hose Connection Port Cover F. Recline Pedal Q. Brush Roller Cover G. AUTO/MAX Mode R. Humidity Sensor H. Power On/Off S. Carpet Deodorizing & Cleaning Solution I. Tube T. Cleaning Tool J. Digital Display U.
EN Digital Display A B C D E F G H I J A. Accessory Hose Icon F. Brush Roller Tangled Indicator B. DWT Full or Blocked G. Dry Degree Indicator C. Dirt Monitoring Loop (Blue to red according to the dirt amount) H. Tineco Logo I. WiFi Indicator J. Water Spray Volume Indicator D. AUTO Mode E.
Accessories Note: Accessories may vary between markets. If you require more accessories, please go to www.tineco.com or store.tineco.com. Removes dirt, grime, grease and tough stains from most types of carpets. Always use Tineco solution in your appliance. Add two bottle caps of solution to each full tank of clean water. Cleaning Tool A full brush to clean the DWT, brush chamber and opening. The tool also has a bristled end to remove dirt and mud on the roller and DWT.
Assembly How to Assemble/Disassemble EN Note: click To assemble the handle, insert it into the appliance until you hear a click. In the event that the product must be returned, please disassemble the handle. Press the spring to release the handle with a tool (like a screwdriver) and lift the released handle from the appliance. Wrap the power cord around the cord hooks for convenient storage.
Clean Water Tank Press the CWT handle to remove it. Open the tank cap, add two bottle caps of solution to the CWT then fill with tap water to the Max line and tightly close the cap. Note: Only use water under 140°F/60°C. DO NOT USE HOT WATER. ② click ① Install the Clean Water Tank into the appliance. You should hear a “Click” if done correctly. Dirty Water Tank ② click ① Install the Dirty Water Tank into the appliance. You should hear a “Click” if done correctly.
Accessory Hose & 2 in 1 Nozzle EN or Choose suitable brush head according to the usage scenario. Pull it up to uncover the accessory connection port. Insert the hose end into the port. You should hear two “Clicks” if done correctly.
Operation EN Preparing for Use (Appliance) Unwrap the power cord and plug into an electrical outlet. Step on the recline pedal to recline the unit for cleaning position. Press the button and the appliance will start in AUTO mode by default. Press it again to turn off the appliance. Switch between AUTO and MAX mode by pressing the button. Press the button and the appliance will start in Dry mode, press it again to stop DRY mode. Switch back to original mode by pressing the button.
° EN <160 Stop Working In AUTO/MAX and Dry mode, the appliance will stop working when put uprightly and start running again when you recline. Grip the back carry handle to lift or move appliance. Empty CWT and DWT after each use. Note: • The carpet cleaner differs from the traditional vacuum cleaner. • In all modes, it blows hot air, whose temperature is 70-80°C. * Appropriate temperature is conducive to dissolve the dirt and helps surfactant in the solution to decompose the dirt.
EN Preparing for Use (Accessory Hose & 2 in 1 Nozzle) Attach the accessory hose, stand the appliance upright and ensure that it is power on (if not, press the button), the appliance will enter in ACCESSORY Mode, the appliance will stop working when you recline. Store the accessories in the bag after use. Note: • Do not vacuum foamed liquid.
Cleaning Mode Selection AUTO Mode Blue Clean: on Min spray volume EN The default spray volume is “60”, vary depending on dirt amount Red Heavy dirt: on Max spray volume • In AUTO mode, the iLoop™ sensor automatically detects how dirty the carpet is and applies the appropriate volume of water spray. • A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is detected. This mode automatically provides the best cleaning solution.
Wet Changes with the degree of humidity Dry • Press the DRY button to enter DRY mode, in DRY mode, the dry degree indicator will change with the humidity detected by the humidity sensor. • Press the DRY button again to stop DRY mode, and press the button to switch to the original mode. ACCESSARY Mode Keep appliance upright • Ensure the appliance is power on (if not, press the button), the appliance will enter into ACCESSARY Mode.
Indicator When in Use MAX mode Spray volume indicator: solid “100”. EN Appliance enters standby mode when stand upright in Max mode. AUTO mode Spray volume indicator: changes. Appliance enters standby mode when stand upright in Auto mode. DRY mode Spray volume indicator: Solid “0”, Dry Degree Indicator illuminated. ACCESSORY mode Spray volume indicator: solid “100”. Accessory icon: illuminated. Appliance enters standby mode when recline in Accessory mode. Accessory icon: blinks.
Indicator blinking: CWT is empty. Indicator blinking: DWT is full or channel has a blockage. DWT is not installed. Illuminated: WiFi has successfully connected. Blinking: WiFi is connecting. Off: WiFi is not connected, please connect to the network. Dry degree indicator blinks, humidity sensor malfunction. App All the functions can be performed using the Tineco app. Download the Tineco app from the App Store, Google Play and Tineco Official Site.
EN Voice Prompt (Contents may vary, please in kind prevail.) Status Reminder WiFi network connected Network connected.
Maintenance Note: • For optimal performance and to prevent odors, always clean and dry DWT, filter, brush roller, brush roller cover, 2 in 1 nozzle, completely after each use. • Please make sure each part is installed correctly or the appliance may not work properly. • After maintenance, place the appliance vertically. Do not expose the appliance to direct sunlight, and store it indoors in a dry place. EN Main Body To reduce the risk of injury, switch off before performing maintenance.
Dirty Water Tank ② EN ① click • When dirty water reaches the Max line, the appliance will stop working and show a reminder on the display and play a voice prompt. • Step on the recline pedal and press the DWT handle to remove it. • Pull up the tank lid to empty the DWT. Use the cleaning tool to remove remaining debris. Rinse the inside of the DWT & tank lid & floater and place back into the appliance. Filter Remove the DWT, take the filter out and wash it after each use. Reinstall.