System One Controller (S1C) S1C Manual page : 2
manual Welcome to Timecode Systems modular S1C PCB. Here we give you a quick tour of this super accurate LTC & Genlock generator, with integrated sub GHz Transceiver and 2.4GHz 802.11b/g WiFi. This will guide you through its key features so you can get up and running straight away. Your timecode revolution starts here… Copyright Notice All rights reserved. No part of this publication may be reproduced without the expressed written permission of Timecode Systems Ltd.
:S1C A guided tour of your highly accurate timecode, genlock generator and multi-channel digital timecode transceiver with integrated WiFi Timecode Mode. Choose from three settings: • INT GEN. Activates the highly accurate internal generator. From here you can set your own T/C, user bits and FPS settings. • EXT RF (Cont). Constantly jam syncs the internal generator from the received T/C via Buddy DataLink. If Buddy loses signal of received T/C, the T/C output continues using the internal generator.
WiFi. Unlocks WiFi enabled features including wireless streaming of timecode to the Timecode Buddy: app System settings. Gives you access to: • TV sync type. Set to OFF, PAL, NTSC, 720p, 720px2, 1080i (PSF), 1080p,1080px2 (x2 double frame rate). Non-standard TC Sync standards and FPS combinations will be automatically rejected. • TV sync level. Set to Std O/P Level for single 75ohm load or High O/P Level for dual 37.5ohm load (2 cameras on T-Piece) • Restore defaults. To remove any customisation.
Detailed specifications S1C Technical specification Timecode generator accuracy: 0.1 ppm TCXO reference oscillator (less than one half frame drift a day). Zero ppm when RF locked. Supported FPS modes: 23.976, 24, 25, 29.97, 30, 29.97DF, 30DF. Output sync modes: PAL, NTSC, 720p, 720p double frame, 1080i(PSF), 1080p, 1080p double frame. Output video sync: 0.6V pp / 75 ohm and 0.6V pp /37.5 ohm for ‘High Level/ Dual load’ WiFi: 2.4 GHz IEEE std. 802.
Frequencies S1C RF transceiver frequencies 1 USA/AU/NZ 915.050 MHz 2 USA/AU/NZ 915.150 MHz 3 USA/AU/NZ 915.250 MHz 4 USA/AU/NZ 915.350 MHz 5 USA/AU/NZ 915.450 MHz 6 USA/AU/NZ 915.550 MHz 7 USA/AU/NZ 915.650 MHz 8 USA/AU/NZ 918.050 MHz 9 USA/AU/NZ 918.150 MHz 10 USA/AU/NZ 918.250 MHz 11 USA/AU/NZ 918.350 MHz 12 USA/AU/NZ 918.450 MHz 13 USA/AU/NZ 918.550 MHz 14 USA/AU/NZ 918.
INDUSTRY CANADA STATEMENTS This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
OEM Responsibilities The Product name here Module has been certified for integration into products only by OEM integrators under the following conditions: 1. 2. The antenna(s) must be installed such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and all persons at all times. The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter.
Warranty and technical support Timecode Systems Limited warrants its products against defects in materials and workmanship for a period of one year from the date of original retail purchase. This is a non-transferable warranty that extends only to the original purchaser. Timecode Systems Limited will repair or replace the product at its discretion at no charge.Timecode Systems Ltd is not responsible for consequential damages arising from use of its equipment, proper or otherwise. Please visit www.
Timecode Systems Ltd Unit 6, Elgar Business Centre, Moseley Rd, Hallow, Worcester, WR2 6NJ, UK t: +44 (0) 1700 808600 e: contact@timecodebuddy.com w: www.timecodebuddy.
