User's Manual

ManualsBrandsTIDRADIO ManualsElectronicsTwo-way Radio

Ｓｍａｌｌｅｒ　ｓｉｚｅ，　ｂｅｔｔｅｒ　ｃｏｍｍｕｎｉｃａｔｉｏｎ

ＵＳＥＲ　ＭＡＮＵＡＬ　ＯＦ　ＳＬＩＭ　ＴＷＯ　ＷＡＹ　ＲＡＤＩＯ

Ｆｕｎｃｔｉｏｎｓ

Ｆｒｅｑｕｅｎｃｙ　ｒａｎｇｅ

Ｖｏｌｔａｇｅ

Ｃｈａｎｎｅｌ　Ｎｏ．

Ａｎｔｅｎｎａ　Ｉｍｐｅｄａｎｃｅ

Ｏｐｅｒａｔｅ　Ｍｏｄｅ

Ｓｉｚｅ

Ｔｅｃｈｎｉｃａｌ　Ｓｐｅｃｓ

ＦＲＳ　　

ＤＣ　３．７Ｖ

２２　ｃｈａｎｎｅｌｓ

５０Ω

Ｓｉｍｐｌｅｘ　ｏｒ　Ｓｅｍｉ－ｄｕｐｌｅｘ

５０ｘ１５ｘ１３０ｍｍ（ｉｎｃｌｕｄｉｎｇ　ｔｈｅ　ａｎｔｅｎｎａ）

Ｉｎｓｔｒｕｃｔｉｏｎ

ＴＯＴ

Ｂａｔｔｅｒｙ　Ｓａｖｉｎｇ

Ｌｏｗ　Ｂａｔｔｅｒｙ　Ｗａｒｎｉｎｇ

ＳＱＬ

Ｆｒｅｑｕｅｎｃｙ　Ｈｏｐｉｎｇ

９、Ｅａｒｐｉｅｃｅ　Ｊａｃｋ

１０、ＵＳＢ　ｃｏｎｎｅｃｔｏｒ

１、Ｐｏｗｅｒ　ｏｎ／ｏｆｆ

　　　　　Ｃｈａｎｎｅｌ　／　

　　　ｖｏｌｕｍｅ　ｓｗｉｔｃｈ

４、ＰＴＴ

２、ＣＨ＋／Ｍｏｎｉｔｏｒ

３、ＣＨ－／Ｆｌａｓｈｌｉｇｈｔ

８、Ｍｉｃｒｏｐｈｏｎｅ

５、ＰＴＴ

６、Ｉｎｄｉｃａｔｏｒ

７、Ｓｐｅａｋｅｒ

Ｒｅ　ｐｒｏｇｒａｍｍｅ　ｂｙ　ｓｏｆｔｗａｒｅ

Ｆｒｅｑｕｅｎｃｙ　ｈｏｐｐｉｎｇ

ＴＯＴ　ｉｓ　ｔｏ　ａｖｏｉｄ　ｓｏｍｅｏｎｅ　ｏｃｃｕｐｙ　ｏｎｅ　ｃｈａｎｎｅｌ　ｆｏｒ　ｌｏｎｇ　ｔｉｍｅ，　

ｙｏｕ　ｃｏｕｌｄ　ｓｅｔ　ｔｈｅ　ｖａｌｕｅ　ｂｙ　ｓｏｆｔｗａｒｅ　（　ｉｔ　ｃｏｕｌｄ　ｂｅ　１５　ｓｅｃｏｎｄ，　３０　

ｓｅｃｏｎｄ，　ｔｏ　６００　ｓｅｃｏｎｄ，　ｒａｎｇｅ　ｉｓ　ｅｖｅｒｙ　１５　ｓｅｃｏｎｄ）．　Ｉｔ　ｗｉｌｌ　ｓｔｏｐ　

ｔｒａｎｓｍｉｔｔｉｎｇ　ｉｆ　ｙｏｕｒ　ｔｉｍｅ　ｉｓ　ｏｖｅｒ　ＴＯＴ　ｖａｌｕｅ，　ｙｏｕ　ｈａｖｅ　ｔｏ　ｒｅｄｏ　ｉｔ　

ａｇａｉｎ．　

Ｅｖｅｒｙ　ｃｈａｎｎｅｌ　ｈａｓ　ｔｈｅ　ｆｒｅｑｕｅｎｃｙ　ｈｏｐｐｉｎｇ　ｆｕｎｃｔｉｏｎ，　ｔｏ　ｐｒｏｔｅｃｔ　

ｙｏｕｒ　ｐｒｉｖａｃｙ　ｔｈｒｏｕｇｈ　ｅｎｃｒｙｐｔｉｏｎ．（ｎｏｔｅ：　ｂｏｔｈ　ｐａｒｔｉｅｓ　ｓｈｏｕｌｄ　

ｃｈｏｏｓｅ　ＯＮ　ｉｎ　ｆｒｅｑｕｅｎｃｙ　ｈｏｐｐｉｎｇ　ｓｅｔｔｉｎｇ）

Ｐｏｗｅｒ　ＯＮ／ＯＦＦ

Ｆｕｎｃｔｉｏｎ　ｋｅｙ

１、ＰＯＷＥＲ　ＯＮ：　Ｒｏｔａｔｅ　ｔｈｅ　ｋｎｏｂ　ｃｌｏｃｋｗｉｓｅ　ｔｏ　ｔｕｒｎ　ｏｎ　

ｔｈｅ　ｒａｄｉｏ，　ａｎｄ　ｕｓｅ　ｔｈｅ　ｓａｍｅ　ｋｎｏｂ　ｔｏ　ａｄｊｕｓｔ　

２、ＰＯＷＥＲ　ＯＦＦ：　Ｒｏｔａｔｅ　ｔｈｅ　ｋｎｏｂ　ｃｏｕｎｔｅｒｃｌｏｃｋｗｉｓｅ　ｔｏ　

ｐｏｗｅｒ　ｏｆｆ．

１、Ｐｒｅｓｓ　ＰＴＴ　ｔｏ　ｔａｌｋ．

２、Ｐｒｅｓｓ　ｋｅｙ　Ｎｏ．　２　ｔｏ　ｉｎｃｒｅａｓｅ　ｔｈｅ　ｃｈａｎｎｅｌ，　ｐｒｅｓｓ　ｌｏｎｇ　

ｔｉｍｅ　ｔｏ　ｍｏｎｉｔｏｒ　ｆｕｎｃｔｉｏｎ．

３、Ｐｒｅｓｓ　ｋｅｙ　Ｎｏ．　３　ｔｏ　ｄｅｃｒｅａｓｅ　ｔｈｅ　ｃｈａｎｎｅｌ，　ｐｒｅｓｓ　ｌｏｎｇ　

ｔｉｍｅ　ｔｏ　ｔｏｒｃｈ．

　Ｌｉｇｈｔ　ｃｏｌｏｒ　ｆｅａｔｕｒｅｓ

１、Ｌｉｇｈｔ　ｃｏｌｏｒ　ｗｉｌｌ　ｂｅ　ｇｒｅｅｎ　ｅｖｅｒｙ　７　ｏｒ　８　ｓｅｃｏｎｄｓ　ｗｈｅｎ　

ｐｏｗｅｒ　ｓｔａｎｄｂｙ．

２、Ｌｉｇｈｔ　ｃｏｌｏｒ　ｗｉｌｌ　ｂｅ　ｒｅｄ　ｗｈｅｎ　ｔｒａｎｓｍｉｔ．

３、Ｌｉｇｈｔ　ｃｏｌｏｒ　ｗｉｌｌ　ｂｅ　ｇｒｅｅｎ　ｗｈｅｎ　ｒｅｃｅｉｖｅ．

Ｌｏｗ　ｂａｔｔｅｒｙ　ｗａｒｎｉｎｇ

Ｌｏｗ　ｂａｔｔｅｒｙ　ｗｉｌｌ　ｒｅｍｉｎｄ　ｙｏｕ　ｔｏ　ｒｅｃｈａｒｇｅ　ｏｒ　ｃｈａｎｇｅ　ｎｅｗ　

ｂａｔｔｅｒｙ．

Ｉｆ　ｔｈｅｒｅ　ｉｓ　ｎｏ　ｅｎｏｕｇｈ　ｐｏｗｅｒ，　ｉｔ　ｗｉｌｌ　ｒｅｍｉｎｄ　ｙｏｕ　ｐｌｅａｓｅ　

ｃｈａｎｇｅ　ｏｒ　ｃｈａｒｇｅ　ｔｈｅ　ｂａｔｔｅｒｙ　ｅｖｅｒｙ　１５　ｓｅｃｏｎｄｓ．

ｓｗｉｔｃｈ　Ｃｈｉｎｅｓｅ　ｏｒ　Ｅｎｇｌｉｓｈ

Ｍａｋｅ　ｉｔ　ｉｎ　ｃｈａｎｎｅｌ　Ｎｏ．　１５，　ｒｅｂｏｏｔ　ｗｈｅｎ　ｐｒｅｓｓ　ｋｅｙ　ＮＯ．３　

ｔｏ　ｓｗｉｔｃｈ　Ｃｈｉｎｅｓｅ　ｏｒ　Ｅｎｇｌｉｓｈ．

003说明书-5.3x9.8cm

■  

C Compliance Statements:

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled

environment. Do not use this device when the antenna shows obvious damages.

Hold this transmitter approximately 25 mm away from your face and speak normal with the

antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other

accessories may not comply to the limits.