Manual

1. The Glow in the Dark Space Coaster is a model roller coaster that comes flat packed for build it yourself fun.
The metal ball is raised to the top of the coaster by the elevator and deposited at the start of the two line rail
- to roll its way to the bottom via twists and turns and a loop-the-loop - before being propelled back to the
beginning by the motorised elevator. Two entry and exit ramps are required with each track, allowing a ball
to be running through the maze at all times.
SHOWN - 1
HOW TO INSTALL THE LOOP (23)
THE STEEL BALL MUST GAIN
MOMENTUM TO TRAVEL THROUGH
THE LOOP
THE DIAMETER OF THE OUTER LOOP
MUST BE TWO TIMES THE DIAMETER
OF THE INNER LOOP TO ALLOW THE
STEEL BALL TO TRAVEL SMOOTHLY
KEY POINTS FOR INSTALLING THE
LOOP (24)
YOU NEED TO MAKE PERFECT
CIRCLES FOR THE LOOP TO BE
EFFECTIVE.
HOW TO INSTALL ELEVATOR “ENTRY”
“EXIT”
KEY POINTS FOR SETTING ELEVATOR
“ENTRY” “EXIT”
THE STEEL BALL CANNOT MAKE A
CONTINUOUS RUN IF THE ENTRY
AND EXIT OF EACH RAIL IS ON THE
SAME SIDE
HOW TO INSTALL ELEVATOR “ENTRY”
“EXIT”
MAKE SURE THE BALL CAN FREELY
ENTER AND EXIT THE ELEVATOR BY
INSTALLING SUPPORT CLIPS, AND
CUTTING RAIL AS PER DIAGRAM 27-1
AND 27-2
HOW TO INSTALL ELEVATOR “ENTRY”
AND THE ANGLE FOR STEEL - BALL
ENTRY
THE STEEL BALL MUST ENTER THE
ELEVATOR AT A SLOW SPEED SO IT
WONT BOUNCE AND FALL OFF THE
RAILS.
AT ENTRY, RUNNING STEEL BALLS
MAY REBOUND WHEN THEY HIT
HELIX. IN THIS CASE, THEY WILL
STOP AS THEY CANNOT RETURN.
NEAR THE ELEVATOR ENTRY, THE
ANGLE OF ELEVATOR AND RAIL
MUST RIGHT-ANGLE
PIC. 25
PIC. 26
PIC. 27-1 PIC. 28
PIC. 28
PIC. 27-2
PIC. 27-2
FIX THE RAIL STAND TO MAKE
THE RAIL AND ELEVATOR AT
RIGHT ANGLES TO AVOID
RAIL BENDING.
DISTANCE BETWEEN RAILS
TO INSTALL THE RAIL STAND TO
KEEP RAILS PARALLEL
ABOUT THE CORNER
KEEP THE RAILS PARALLEL WHEN
MAKING SMOOTH CORNERS.
ADJUST RAILS IF BALLS FALL OFF
THE TRACK BY ANGLING THE ARMS
AND SUPPORTS TO BETTER HOLD
THE BALL.
ADJUST THE RAIL TO A SLOWER
SPEED WHEN MARBLE IS TRAVELING
AROUND CORNERS
YOU NEED A CERTAIN ANGLE AT THE CORNERS TO
KEEP THE BALL ON THE TRACK
PIC. 20
PIC. 21 PIC. 22
SLOW THE BALL BEFORE ENTERING THE CORNER
BASIC STARTING ROUTE PICTURE
2. To the right and below are pictures of
the Glow in the Dark Space Coaster from
different angles to assist during
construction of the model.
SHOWN.2 - FRONT
SHOWN.3 - LEFT SIDE SHOWN.4 - TOP SHOWN.5 - RIGHT SIDE
SHOWN.6 - BACK
THIS RAIL INCLUDES 2 ELEVATOR ENTRIES AND
EXITS REFER TO PIC. 12 - PIC. 13 AND PICTURES
ON PAGE 2-3 WHEN ASSEMBLING.
RUN SHOULD BE ASSEMBLED IN ONE
CONTINUOUS STRING FOR EACH SIDE OF THE
RAIL. DO NOT CUT.
1. ELEVATOR EXIT (START) - THE FRONT OF RING
REFER TO THE ENLARGED PICTURE FOR MORE
DETAIL ON HOW TO ADJUST THE LOOP. RAILS CAN
BE ADJUSTED LATER TO BETTER HOLD AND
ACCELERATE THE STEEL MARBLE.
REFER ON P11 TO ADJUST THE RAIL IF
THE STEEL BALL CANNOT SMOOTHLY ENTER
THE ELEVATOR.
PIC. 27
THE LENGTH OF THE RAIL CAN BE CUT AS NEEDED FOR INSTALLATION REFER TO P9 “RAIL JOINING”
Note: Insert the Helix in the correct
direction as shown in diagram.
3. INSERT 3PCS 300MM SHAFT
INTO THE RELEVANT HOLE ON
GEAR BOX AS SHOWN
4. LOCK 3PCS SHAFTS (NOTE
CORRECT DIRECTION OF THE 3
RINGS ON DIAGRAM)
REFER TO P6, P7 FOR THE
PLACE OF ELEVATOR RING
5. INSERT 4 PCS OF SHAFT
ONTO THE COVER OF THE
ELEVATOR AS PER PICTURE.
NOTE CORRECT POSITION IN
THE DIAGRAM.
3
NOTE THE CORRECT
DIRECTION OF THE HELIX
PARTS
ALLOW SOME SPACE BETWEEN THE
GEAR BOX AND THE ELEVATOR HELIX
TO ALLOW THE ELEVATOR TO TURN
FREELY
RED PART ON THE DIAGRAM, CONVEX
SIDE UP, NOTE THE DIRECTION WHEN
ASSEMBLING.
ASSEMBLE EACH METAL
SHAFT AS PER DIAGRAM (1:1
ACTUAL SIZE AND POSITION)
TO ASSEMBLE THE ARMS
(RAIL HOLDERS) LEFT AND
RIGHT REFER TO PARTS LIST
ON PAGE 4
BE CAREFUL WHEN INSERTING
KEEP AWAY FROM CHILDREN AND PETS
BATTERY INSTALLATION SHOULD BE DONE BY AN ADULT
INSTALL BATTERY CORRECTLY IN THE BATTERY COMPARTMENT
RECHARGEABLE BATTERIES ARE NOT SUITABLE TO BE USED FOR THIS PRODUCT
BE CAREFUL OF SHARP EDGES WHEN ASSEMBLING
CHILDREN UNDER 14 SHOULD HAVE ADULT SUPERVISION
KEEP FINGERS AWAY FROM RUNNING ELEVATOR TO AVOID INJURY
DO NOT RUN FOR MORE THAN 5 HOURS AT A TIME TO AVOID OVERHEATING
NOT INTENDED FOR CHILDREN UNDER 3
CHOKING HAZARD SMALL PARTS
WARNING
HOW TO INSTALL THE RAIL
HOW TO INSERT THE RAIL
INTO ARM
RAIL JOINT
MODIFY OR ADJUST YOUR
DESIGN BY CONNECTING
SHORTER PIECES OF RAIL
BY INSERTING THE SMALL
PINS ENCLOSED.
ABOUT THE RAIL STAND
THE DISTANCE BETWEEN
THE ARMS SHOULD BE
9-10CM TO ADD STABILITY
TO THE TRACK AND
ALLOW ADJUSTMENT.
INSERT RAIL STAND TIES
AS IN DIAGRAM 18.
ATTACH THE RAIL WITH
ADDITIONAL CLIPS TO THE
ENTRY AND EXIT OF THE
ELEVATOR TO STABILIZE.
FALLING AND CLIMBING
KEEP THE RAILS STRAIGHT
AND ANGLE DOWN TO
ALLOW THE METAL BALL
TO GAIN MOMENTUM AND
BE ABLE TO CLIMB
INCLINES.
MAKE THE ARM INCLINE
AS
9
Requires one “C” battery (not included)
3. Store the small parts in order to avoid misplacement.
MOVED.
Space Coaster - Glow In The Dark
thumbsUp! (UAE)
Best Homes Business Center
M 107, Mezzanine Floor
Sheik Zayed Road
Dubai, UAE
T: [phone]
F: [phone]
Mail: [e-mail]
Web: www.thumbsup.ae
thumbsUp! (BR)
Departmento Comercial
Rua Henrique Jorge Guedes
127Jardim Marajoara
Sao Paulo, Brazil
T: [phone]
F: [phone]
[e-mail]
www.thumbsup.br.com
thumbsUp! (FR)
164 av Joseph Kessel,
78960 Voisin le
Bretonneux, FR
T: [phone]
F: [phone]
[e-mail]
www.thumbsup.fr
thumbsUp! (USA)
thumbsUp! USA, 841-B
Fesslers Parkway, Nashville,
TN 37067, USA
T: 615-620-1370
F: 615-620-1371
[e-mail]
www.thumbsupusa.com
thumbsUp! (AUS)
Unit 1, 113 Broadway,
Bassendean, WA 6054
Australia
T: 1300 873 637
F: 1300 304 870
Mail: [e-mail]
Web: www.thumbsupaus.com
thumbsUp! (DE)
thumbsUp! GmbH
Speestr. 24
53840 Troisdorf, DE
T: [phone]
F: [phone]
[e-mail]
www.thumbsup.de
thumbsUp! (UK)
Santok House, Unit L, Braintree Industrial Estate
Ruislip, Middlesex, HA4 0EJ, UK
Tel: [phone]
Fax: [phone]
[e-mail]
www.thumbsupuk.com
Head Office
Made in ChinaSPCCOAS-GLOW