1105 2.4 GHz Digital Caller ID with Call Waiting Cordless Multi-Handset System with Full-Duplex Handset Speakerphone User's Guide FCC ID: GOH2-1105A. Mars tech Report No.
EQUIPMENT APPROVAL INFORMATION Your telephone equipment is approved for connection to the Public Switched Telephone Network ang is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements far Telephone Terminal Equipment published by ACTS. 1 Notification to the Local Elephants Company On the bottom of this equipment is a labial indicating, among other information, the US number and Ringer Equivalence Number {BEN for the equipment.
INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following twa conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for 5 Class B digital device, pursuant to Part 15 of the FCC Rules.
INTRODUCTION GETTING TO KNOW YOUR MULTI-HANDSET CORDLESS SYSTEM CAUTION: When using telephone equipment, there are basic. safety instructions that should always be Followed. Refer o the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. Congratulations on purchasing this GE Multi-handset Telephone Stern. This system operates in the 2.4 GHz frequencies and is unique to conventional cordless telephones.
Your Caller I} Call Waiting hons allows you to: View the name and telephone number of a caller [Call Waiting Caller 10) Identify callers before you answer the phone. * View the time and date of sate incoming call. Record up to 40 Caller ID messages sequentially. Know wha called while you are on the other line or when yau were away.
Harasser Lay Out display VOICE MAIL button VOL buttons SPEAKER button REPEAT/DIAL button REDIAL FORMAT button INFO bunion AUTO REDIAL TALK button button PROVOKING button headset jack UP/CID button DOWN/DIR button DELETE button TONE button PAUSE bunion INT/TRANSFER button FLASH/ 3 WAY/ EXIT buttons HOLD button MUTE button Base Layout charge indicator in use/ page indicator page button
Parr Sarcastic Make sure your package includes the items Shawn here, If any of these stems dre missing or damaged, contact the Thomson multimedia Inc, Mail Order Department at 1-800-338-0376. Handset battery Belt clip AC power supply ‘Telephone fine cord Mobutu Jack REQUIREMENTS You need an CRITIC type modular jack, which is the most common type of phone jack and might look like the ona pictured here. If wl you don't have a modular Jack, call your local hons company to | find out how to get one installed.
IMPORTANT INSTALLATION Guidelines Install telephone near both a telephone (modular) jack and an electrical power outlet. Avoid sources of noise, such as a window by a busy street, and electrical notch, such motors, microwave ovens, and fluorescent lighting, Avoid heat sources, such as heating air ducts, heating appliances, radiators, and direct sunlight Avoid areas of excessive moisture or extremely low temperature, Avoid dusty locations.
INSTALLING THE PHONE Chose the best location ta install your cordless multi-handset system. Your cordless multi-handsst system should be placed on 2 level surface Ugh cen desk or tabletop. CONNECTING THE AC (ELECTRICAL) POWER Plug the power supply cord into the power jack on the back of the base and the either end into an electrical outlet. The charge/page indicator turns on to indicate the battery is charging, Allow the phone to charge for 8 hours prior to first use.
THE Basics MULTI-HANDSET System BUTTONS DEFINED Hanover Burros: NUMBER/ TOUCHSTONE PAD Dials numbers and enters text TALK Starts external calls and answers calls FLASH Triggers special phone company services ssh ss call waiting EXIT Exits programming, directory, or Caller ID mode MUTE Turns off the handset microphone REDIAL Redials last number sidled PAUSE inserts a time delay {pause} in the number dialing sequence HOLD Places an outside call an hold TRANSFER Transfers an active call to another handset INTE
PROGRAMMABLE MENUS There are several different menus available on the handset, which are programmable through the display box: LANGUAGE, INTERCOM RING, LINE RING, RING VOLUME, RING TYPE, AREA CODE, VOICE MAIL, INFO SERVICE, HOLD REMINDER, RESET HANDSET, and REGISTRATION. Below table shows the items, which can be set.
I. You may only use the handset to select by pressing the [PROGRAM] key whe >LANGUAGE INTERCOM RING LINE RING 2. Press [OK] (the same key as the [PROGRAM] key) show: LANGUAGE ENGLISH [01/00]: CHANGE 3. Press [UP/DOWN] key to change the item, 4. Press [OK] (the same as [PROGRAM] key) to coir show: LANGUAGE ENGLISH t language. Make sure you let the handset enter into menu mode n you're not on line.
Note: Press {EXT] to keep the previous setting and return to the main menu screen, 5. After 3 seconds, the Display Box will come back the upper level to program the other items, The Display Box will show: >INTERCOM RING LINE RING RING VOLUME LINE RING SELECTION 1. Make sure the handset in standby mode, Press [PROGRAM] key to enter into menu mode. 2. Press [UP] or [DOWN] until the arrow points to the “LINE RING”. Cross [OK] key to go to line ring setting.
RING VOLUME HIGH OK! Note: Press {EXIT to keep the previous setting and return to the main menu screen, 5. After 3 seconds, the Display Box will come back the upper level to program the other items, RING TYPE SELECTION 1. Make sure the handset in menu node, 2. Press [UP] or [DOWN] until the arrow points to the “RING TYPE”, Press [OK] key to £0 10 ring type sating. Default Setting is “1”, RING TYPE 1 [01/00]: CHANGE 3.
3. Enter your 3 digits area code. For example, if you live in Los Angeles, it would be: AREA CODE 213 4. Press [OK] (the same as [PROGRAM] key} to confirm and save the selection, the Display Box will show as below for 3 seconds. AREA CODE 213 Note: Press [EXIT] to keep the previous setting and return to the main menu screen. You also can delete the area code by pressing the [DELETE] key.
VOICE MAIL 5235552468 Note: Each handset can be set on a different voice mail number. ‘You can also delete the voice mail number using the [DELETE] key, Press the [DELETE] key. The Display Box will show: VOICE MAIL 5235552468 DELETE? Press [DELETE] again to confirm. The Display Box will show: EDITING THE INFO SERVICE NUMBER 1 2. wr VOICE MAIL EMPTY Make sure the handset in menu mode. Press [UP] or [DOWN] until the arrow points to the “INFO SERVICE”. Press [OK] key to go io Info. Service number editing.
Press [DELETE] again to confirm, the Display Box will show: INFO SERVICE 411 HOLD REMINDER “The {Hold Reminder] will wait a certain period of time to generate double beeps after an outside call is put an hold. Such beeps are intended to remind you a held call is still there. Choices for wait duration are: OF / 15/30/45 /60 Seconds. Default is 30 seconds. 1. Make sure the handset in memo mode. 2. Press [UP] or [DOWN] until the arrow points to the “HOLD REMINDER”, Press [OK] key to go to area code setting.
3. Press [UP/DOWN] key to toggle [YES?] or [NOT] RESET HANDSET YES? [01/00] : CHANGE Note: [YES] means reset, while [NO] means exit without reset. 4. At the [YES?] prompt, press [OK] (the same as [PROGRAM] key) to confirm. The Display Box will show: HANDSET RESETTING. . . PLEASE WAIT! 5. After 3 seconds, the Display Box will show the following message for 5 ~ 10 seconds. INITIALIZING... PLEASE WATT! HANDSET REGISTRATION Do the following procedures to register the handset to base unit, 1.
6. Press [OK] (the same as [PROGRAM] key) to confirm the selection, and the Display Box will show: PUT HANDSET ON THE BASE TO REGISTER 7. Put the handset on the base unit to register it with the base unit. When the registration is done, confirmation beep can be heard and the Display Box shows as below for 3 seconds. REGISTERED HANDSET ID=2 8. If it fails to register after 10 seconds, the Display Box will show: REGISTRATION FAILED! TRY AGAIN! Note: 1.
BASIC OPERATION MESSAGE DISPLAY In standby status, the following messages will be displayed according to the conditions of the handset and the line status, XX NEW CALLS XX new calls has been received and unread. XX CID RECORDS XX caller ID records has been received. LINE IN USE The line is in use.
iv) You can use [UP] and [DOWN] keys to move the cursor forwards and backwards in the redialing mode. ANSWERING CALL 1. Check the display to seo who is calling and press the [TALK] key (or [SPEAKERPHONE] key) in the handset to answer the call, 2. When finished, press the [TALK] again to or put the handset back to the base fo hang up. Note: When any handset picks up the ling, all the other handsets will display [LINE IN USE] LAST NUMBER REDIAL (LNR) 1.
RECALL RING LINE ON HOLD PAGING ALL HANDSETS From time to time you may have misplaced handsets you can't find. Press {Page] key on the base unit to make all handsets ring for 60 seconds, 50 you can trace the sound to find them, The Display Box will show: PAGING ALL HANDSETS FROM BASE Once the handsets are found, you can press [EXIT] key or any number key on the handsets to stop the paging ring.
Press [MUTE] again to cancel mute and return to the conversation, Note: If you hang up or flash the line, MUTE will be canceled automatically. SPEAKERPHONE Your handset is equipped with speakerphone. During your phone conversation, press the [SPEAKERPHONE] key to turn on the speakerphone if you want to talk in speakerphone mode. ‘While talking in speakerphone mode, press [SPEAKERPHONE] key again and then the phone will switch back to normal mode.
BATTERY LOW WARNING ‘When the battery voltage level is low, the warning message “LOW BATTERY” appears. If you are on the line, you can hear double warning beep. At this time, finish your call as soon as possible. Or, the call will be put on hold by the base automatically and you would need another handset to retrieve the call, INTERCOM At any given time, first-come-first-serve, the system provides one intercom path for two inside users.
SYSTEM BUSY 3. If intercom's called party doesn't answer the call in 60 seconds, this intercom call will be canceled automatically. 4. The system doesn’t provide any tonic dial tone/ring back tone/busy for intercom operation. IF THE INTERCOM PATH IS BUSY If the intercom path is already taken by other users, your handset will give a warming beep when you press the (INTERCOM] key. At the same time, “INTERCOM BUSY” message will be displayed.
Your handset will give a warning beep. And, keep the above screen for abort 10 seconds. ANSWERING INTERCOM CALL “You can hear the intercom ringer while sexing the Display Box as below: INTERCOM FROM HANDSET #3 RINGING Press [INTERCOM] key to answer the intercom call. Your Display Box will show: INTERCOM FROM HANDSET #3 TALKING Or, press [SPEAKERPHONE] to answer the call in speakerphone mode: INTERCOM FROM HANDSET #3 SPEAKERPHONE Either party can press [INTERCOM] to hang up the intercom call.
party, 4. Intercom's called party can press [INTERCOM] or [SPEAKERPHONE] key 10 answer the call, 5. When finished, either party can press [INTERCOM] to hang up the intercom call. And, the fine still will be kept on hold. RECEIVING AN INCOMING CALL DURING INTERCOM During an intercom call, if a telephone is received, both users are alerted with a ting tone. Before taking the Tine, you should press the [INTERCOM] key to terminate the intercom call. Then, you press [TALK] key to pick up the call.
LINE ON HOLD >INTERCOM? TRANSFER? 2. Press [OK] key and then followed by the handset number you want to naked intercom, for example, #2. INTERCOM TO HANDSET #2 LINE ON HOLD 3. User of handset #2 can hear the intercom ringer and press [INTERCOM] key to pick up the call. INTERCOM FROM HANDSET #3 TALKING 4. After intercom set up, your Display Box will show: INTERCOM TO #2 >TRANSFER? CONFERENCE? 5. Press [OK] key at the TRANSFER prompt, User of handset #2 doesn’t need to do anything. The transfer will be done.
intercom, for example, #2. 3. After the calling party press the [INTERCOM] key to answer the intercom call, the intercom call is set up. 4. The display box of your handset will show; INTERCOM TO #2 >TRANSFER? CONFERENCE? 5. You can use the [UP/DOWN] key to select conference. And press [OK] key to build the conference call. User of handset #2 doesn’t need to do anything. The conference call will be build automatically.
Or, when the phone is idle, press [INFO], The phone will automatically pick up the ling and dial out the per-set Info service number. REPEAT DIAL BUTTON OPERATION With the phone on line, if the dialed out number is busy, press [REPEAT DIAL]. The phone will send your command to your Telephone Company and your Telephone Company will repeat dial the number on your behalf. Or, when the phone is idle, press [REPEAT DIAL].
Company, then send the proper digit to your Telephone Company to reach your Telephone Company features 4. The dial out digits for the Telephone Company features won't be store into the redial memory. It also includes whole digits that follow your Telephone Company features digits. DIRECTORY OPERATION Your handset's Directory Memory can store up to 10 records of names and phone numbers. Each name can letters, and each number up to 24 digits. STORE A NAME AND A NUMBER IN MEMORY 1.
“8” key once for the fetter T, press the “4” key twice for the letter H. You can press [UP] or [DOWN] key to move the cursor, and then press [DELETE] key to delete one character if you wants to make change in the name Below is the table to let you know what letters are stored in each key. for [SPACE] T&,. ()@1 for AB, For DE Def for GH IL ghoul For Gor M,N, O,m n,0,6 7fr PQR Spears For TU, Vitus For WX YZ wxv29 * for * 0 for 0 # for # PAUSE (display [P]) 7.
record is #1, and the last record is #0. Press [UP/DOWN] to select the directory index 1>John smith 2 Jacky Chen [ok]: ENTER Press [FORMAT] key to change the display for the number of the record, It will show as below: {showing the first 14 digits if more than 14) You can press [FORMAT] key again to show the names again, 1>12123456789 2 13592252468 [OK]: ENTER Press [OK] to and then the Display Box will show: 12123456789 John smith 6.
(NUMBER EMPTY) (NAME EMPTY) DIAL OUT A NUMBER FROM DIRECTORY MEMORY I. Make sure the handset being in the standby mode, 2. Press the [DIR] key. The display is shown as below. There are 10 records in the directory, the first record is #1, and the last record is #0. 3. Press [UP/DOWN] to select the directory index 1>John smith 2 Jacky Chen [OK] :ENTER 4. Press [TALK] to pick up the line and dial out the number, ~OR3. Press {OK] to and then the Display Box will show as below.
CHAIN DIALING WITH DIRECTORY MEMORY Use this feature to make calls that require a sequence of numbers, such as a calling card number used for a frequently called long distance number. The following example shows how you can store each part of the long dialing sequence and use chain dialing to make a call through a long distance service, EXAMPLE Note: 1. The Chain-Dialing function could combine the following cases. Manual Dialing + Directory {b) Directory + Manual Dialing {cy Directory + Directory 2.
If the caller ID record has been reviewed, the and [repeat counter] signs will disappear. 2.{ 2/01] ~ Month/Date. The month range: 01 to 12, the date range: the month/date data is out of the range, Display Box will show blank. 3. {1:55A]HourMinute AM/PM. Hour range from 00 to 23 minute range: the housemistress data is out of the range, Display Box will show blank. CALLER ID DATA BASE Up io 50 Callers can be stored in the Database of the base unit on a numbered lst. This list can be reviewed at any time.
If the database is empty, it will show: NEW CID:00 ALL CID:00 Note: The Caller ID Database Retrieve uses the muse radio path as the intercom path. So, the Display Box will show System Busy when any user tries to access the Caller ID Database when an intercom is ongoing or CID database is being accessed by another user;, SYSTEM BUSY DELETE ALL CALLERS FROM THE CALLER DATA BASE Press [CID], Display Box shows all caller information: NEW CID:XX ALL Cindy {REVIEW Press [DELETE] key to delete the all caller data.
calling time. If the same caller calls many times on another day (tomorrow), the caller ID database will keep the information in another records. DIAL BACK FOR THE CALLER ON DISPLAY While reviewing Caller ID records, you can call the caller phone number showing in the display. Press [CID] to enter Caller ID database. 2. Press [DOWN] key, you will sce the newest caller. Or press [UP] key to view the oldest record. Press [FORMAT] key to change the format of the number.
1. Press [FORMAT] key again and again to select a right number format that you want. 2. Press and hold the [DIRECTORY] key for more than onc second to enter the directory index. The Display Box will show, for example: 1>Mary 2 Mother 3. Press [UP] or [DOWN] key to select an index location: 6>Ricky 7 EMPTY [OK] :ENTER 4. Press [OK] key to confirm the selection, the Display Box displays: REPLACE RECORD? YES? >NO? 3. Press [ENDOWMENT] to select [YES] inert. And press [OK] to confirm the storing into memory.
GENERAL Product CARE To keep your unit working and locking good, follow these guidelines: Av old dropping the handset, as wall as other rough treatment to the phone.