User's Instructions

ManualsBrandsThingsee Nano Tag ManualsAsset TrackersAsset tracking tag

Table Of Contents

User Instructions, Thingsee Nano

User Instructions, Thingsee Nano
TTG USER INSTRUCTIONS
INTRODUCTION AND INTENDED USE OF TTG
INSTALLATION AND COMMISSIONING GUIDELINES
PRECAUTIONS
LEGAL NOTICES
RECYCLING
FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES
FCC Information for the User
FCC Guidelines for human Exposure
Federal Communications Commission Statement
FCC Radio Frequency Interference Warnings & Instructions
FCC Caution
The following document describes how the Nano tag is installed and used in asset tracking use cases.
TTG USER INSTRUCTIONS
 
INTRODUCTION AND INTENDED USE OF TTG
TTG (Thingsee Nano Tag) is a 0.5” x 1.0” x 0.25” sized Bluetooth device that is used for tracking assets. Device has 5 years of operation 
time in specific use cases where the main functionality is to beacon in specified interval. Communication happens using Wirepas 5.1 DA 
communication protocol. Construction of the tag is very simple by including only two mechanical covers, PWB assembly and two batteries. 
The appearance of TTG is shown in the picture below.
 
INSTALLATION AND COMMISSIONING GUIDELINES
TTG is delivered as batteries pre-installed in place. The device has two CR1025 lithium batteries, recommended manufacturer is Renata.

Summary of content (11 pages)

PAGE 1
User Instructions, Thingsee Nano TTG USER INSTRUCTIONS INTRODUCTION AND INTENDED USE OF TTG INSTALLATION AND COMMISSIONING GUIDELINES PRECAUTIONS LEGAL NOTICES RECYCLING FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES FCC Information for the User FCC Guidelines for human Exposure Federal Communications Commission Statement FCC Radio Frequency Interference Warnings & Instructions FCC Caution The following document describes how the Nano tag is installed and used in asset tracking use cases.
PAGE 2
Before installation of the device, make sure that the needed infrastructure (gateways, routers and mini beacons) is installed correctly for asset tracking. TTG has a plastic slip serving two purposes. It protects the two sided tape used for attachment and disconnects the batteries from the electronics when the device is not yet taken into use. The surface for attachment needs to be flat and clean, IPA solvent (isopropyl alcohol) should be used for cleaning the surface.
PAGE 3
When placing the device in the desired position, press the device for 5 seconds to make sure that the tape is correctly attached on the surface.
PAGE 4
Pull away the plastic slip from the device and it powers on and connects automatically to the surrounding asset tracking infrastructure.
PAGE 5
If you need to change the batteries, first push the snap on the side inwards using a suitable small tool in order to open the device. Push the batteries out from the device end having a smaller opening in the cover.
PAGE 6
Push the new batteries in from the end having a larger opening in the cover.
PAGE 7
PAGE 8
Snap the bottom cover back to its place.
PAGE 9
PRECAUTIONS This equipment is not suitable for use in locations where children are likely to be present. TTG is intended for indoor use only and shall not be exposed to rain. The operating temperature range for the device is -20…+50 °C. Remove the batteries from the TTG device if you are taking it inside an aeroplane (unless you have the pre-installed pull-out tape still in place). The device has a Bluetooth LE receiver/transmitter which must not be operational during a flight.
PAGE 10
Haltian Oy Yrttipellontie 1 D 90230 Oulu Finland RECYCLING Check the local regulations for proper disposal of electronic products. The Directive on Waste Electrical and Electronic Equipment (WEEE), which entered into force as European law on 13th February 2003, resulted in a major change in the treatment of electrical equipment at endof-life.
PAGE 11
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods: Increase the separation between the equipment and the receiver.