User's Manual

ManualsBrandsThermo Scientific ManualsElectronicsW1001 Module

Integrated Transceiver Modules for WLAN 802.11 b/g/n, Bluetooth,

Bluetooth Low Energy (BLE), and ANT

FEATURES

IEEE 802.11b,g,n,d,e,i compliant

 Typical WLAN Transmit Power:

o 20.0dBm, 11 Mbps,CCK (b)

o 14.5dBm, 54 Mbps,OFDM (g)

o 12.5dBm, 65 Mbps,OFDM (n)

 Typical WLAN Sensitivity:

o -89dBm, 8% PER, 11 Mbps

o -76dBm, 10% PER, 54 Mbps

o -73dBm, 10% PER, 65 Mbps

 Bluetooth 2.1+EDR, Power Class 1.5

 Full support for BLE 4.0 and ANT

 Miniature footprint: 18 mm x 13 mm

 Low height profile: 1.9 mm

 U.FL connector for external antenna

 Terminal for PCB/Chip antenna feeds

 Integrated band-pass filter

 Compact design based on Texas

Instruments WL1271L Transceiver

 Seamless integration with TI OMAP™

application processors

 SDIO Host data path interfaces

 Bluetooth Advanced Audio Interfaces

 Low power operation mode

 RoHS compliant

APPLICATIONS

 Security

 HVAC Control, Smart Energy

 Sensor Networks

 Medical

DESCRIPTION

The W1001 module is a high performance 2.4

GHz IEEE 802.11 b/g/n, Bluetooth 2.1+EDR,

and Bluetooth Low Energy (BLE) 4.0 radio in a

cost effective, pre-certified footprint.

The module realizes the necessary PHY/MAC

layers to support WLAN applications in

conjunction with a host processor over a SDIO

interface.

The module also provides a Bluetooth platform

through the HCI transport layer. Both WLAN

and Bluetooth share the same antenna port.

Summary of content (14 pages)

PAGE 1
Integrated Transceiver Modules for WLAN 802.11 b/g/n, Bluetooth, Bluetooth Low Energy (BLE), and ANT FEATURES IEEE 802.11b,g,n,d,e,i compliant  Typical WLAN Transmit Power: o 20.0dBm, 11 Mbps,CCK (b) o 14.5dBm, 54 Mbps,OFDM (g) o 12.5dBm, 65 Mbps,OFDM (n)  Typical WLAN Sensitivity: o -89dBm, 8% PER, 11 Mbps o -76dBm, 10% PER, 54 Mbps o -73dBm, 10% PER, 65 Mbps  Bluetooth 2.1+EDR, Power Class 1.5  Full support for BLE 4.0 and ANT  Miniature footprint: 18 mm x 13 mm  Low height profile: 1.
PAGE 2
W1001 MODULE FOOTPRINT AND PIN DEFINITIONS To apply the W1001 module, it is important to use the module pins in your application as they are designated in below and in the corresponding pin definition table found on pages 7 and 8. Not all the pins on the W1001 module may be used, as some are reserved for future functionality.
PAGE 3
PIN DESCRIPTIONS ModulePin Name I/O Type Buffer Type Logic Level 1 VBAT PI - - 2 BT_FUNC5 DO 4 mA 1.8 VDC HOST_WU (*) 3 WL_UART_DBG DIO 4 mA 1.8 VDC WL_UART_DBG 4 WLAN_IRQ DO 4 mA 1.8 VDC WLAN Interrupt Request 5 BT_EN DI - 1.8 VDC Bluetooth Enable 6 FM_EN DI - 1.8 VDC NOT SUPPORTED, CONNECT TO GND 7 WL_RS232_RX DI - 1.8 VDC WLAN TEST UART RX (*) 8 WL_RS232_TX DO 4 mA 1.8 VDC WLAN TEST UART TX (*) 9 FM_I2S_FSYNC DO 4 mA 1.
PAGE 4
ModulePin Name I/O Type Buffer Type Logic Level 32 FM_AUD_LOUT AO - - 33 AUD_FSYNC DIO 4 mA 1.8 VDC PCM I/F 34 HCI_RX DI 8 mA 1.8 VDC Bluetooth HCI UART RX (*) 35 HCI_RTS DO 4 mA 1.8 VDC Bluetooth HCI UART RTS (*) 36 HCI_TX DIO 8 mA 1.8 VDC Bluetooth HCI UART TX 37 AUD_CLK DO 4 mA 1.8 VDC PCM I/F (*) 38 AUD_OUT DO 4 mA 1.8 VDC PCM I/F (*) 39 HCI_CTS DI 4 mA 1.8 VDC Bluetooth HCI UART CTS (*) 40 AUD_IN DI 4 mA 1.8 VDC PCM I/F (*) 41 BT_FUNC2 DO 4 mA 1.
PAGE 5
ELECTRICAL SPECIFICATIONS The majority of these characteristics are based on controlling and conditioning the tests using the W1001 control software application. Other control conditions may require these values to be recharacterized by the customer. Absolute Maximum Ratings Parameter Min Max Unit Power supply voltage (VBAT)(4)(5) -0.5 +5.5 V Digital supply voltage (VIO) -0.5 2.1 V -0.5 VIO + 0.5 V -0.5 2.
PAGE 6
General Characteristics Parameter WLAN RF frequency range WLAN RF data rate BT RF frequency Range Min Typ 2412 1 802.11 b/g/n rates supported 2402 Max Unit 2472 MHz 65 Mbps 2480 MHz Table 4 General CharacteristicsSoldering Recommendations Recommended Reflow Profile for Lead Free Solder Note: The quality of solder joints on the castellations (‘half vias’) where they contact the host board should meet the appropriate IPC Specification.
PAGE 7
Cleaning HANDLING AND STORAGE In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Handling    Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels.
PAGE 8
AGENCY CERTIFICATIONS FCC ID: Z4H-W1001 IC: 9812A-W1001 AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 9
Industry Canada Statements This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
PAGE 10
OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The W1001 Module has been certified for integration into products only by OEM integrators under the following condition: To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be operating in conjunction with any other antenna or transmitter, except
PAGE 11
OEM LABELING REQUIREMENTS FOR END-PRODUCT The W1001 module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module.
PAGE 12
OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product.
PAGE 13
MECHANICAL DATA Figure 3 Module Mechanical Dimensions (Maximum Module Height = 1.
PAGE 14
Figure 4 W1001 Recommended PCB Footprint (Top View)