Installation Sheet

ManualsBrandsThermaSol ManualsSteam generatorsThermaSol DaySpa 12kW Steam Generator - 3 Room System

81098 Page 1 of 21 REV L 10/18 NJL

DATE

CODE

HERE

Installation Instructions

Day Spa Generator

If you are a plumber installing this unit, please leave

this owner’s manual & warranty card with the owner

when you finish the installation.

This Instruction supercedes all previous information provided by ThermaSol

Thank You!

CONSUMER WARNING

 DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED YOUR DOCTOR AND RECEIVED WRITTEN

PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH.

 STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS “ON”, UP TO ONE

HOUR FROM THE TIME THE UNIT IS OFF. SEVERE BURN WILL OCCUR IF YOU COME IN CONTACT WITH THE

STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.

 NEVER ATTEMPT TO FILL AROMA THERAPY RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE “ON”

POSITION. SEVERE BURNS WILL OCCUR.

 DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY PRODUCT IN

CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH YOUR ALLERGIST OR DOCTOR

BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO YOUR HEALTH.

 YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR FLOORING

MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM APPLICATION. SLIPPING AND

FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM OF STEAM EMITTING FROM THE STEAMHEAD WILL

CAUSE SERIOUS BURNS, OR PHYSICAL INJURY.

 DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS CAN BE

HAZARDOUS TO YOUR HEALTH.

 IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP IMMEDIATELY EXIT THE

STEAM ROOM.

 DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN ADULT.

Note: Before contacting Customer Service for Technical Support, please have the model number,

serial number and date code include all numbers and letters.

Headquarters & Technical Support

1958 Steam Way, Round Rock, TX 78665 – (800) 776-0711

Mon – Fri 7:00 – 7:00 CST

PLACE SERIAL # HERE

Summary of content (21 pages)

PAGE 1
Installation Instructions Day Spa Generator If you are a plumber installing this unit, please leave this owner’s manual & warranty card with the owner when you finish the installation. This Instruction supercedes all previous information provided by ThermaSol Thank You! CONSUMER WARNING  DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH.
PAGE 2
** NOTICE ** YOU MUST ATTACH THE USER WARNING LABEL IN THE SHOWER NEXT TO THE CONTROL UPON COMPLETION OF INSTALLATION. LOCATE THE STEAM HEAD 6” INCHES BELOW CEILING AND 6 INCHES FROM NON BENCHED/SEATED/DOOR INTERIOR WALL CORNER. STEAM HEAD IS TO BE MOUNTED AS FAR AS POSSIBLE FROM TYPICAL BATHING POSITION (SEATED OR STANDING) AND AS FAR FROM CONTROL AS POSSIBLE WHILE MAINTAINING APPROXIMATELY A – 60” CONTROL HEIGHT.
PAGE 3
Sizing Your Steam Room Factory Sized: L x W x H = Cubic Feet Then choose the appropriate Model. No complicated formulas. It’s that simple. For every foot of ceiling height over 8 ft. (always round up) use the next larger steam unit. Wall material irrelevant. Generator Model Factory Sized Cu Ft MAX KW Day Spa 150 Day Spa 250 Day Spa 400 Day Spa 650 150 250 400 650 10 12 16 20 Figure 1 Various options for the ThermaSol steam bath generator location.
PAGE 4
Requirements for Proper Installation 1. Ensure the steam rooms to be used are vapor proof. They should have a vapor proof door that seals well so the steam does not escape. Make sure the walls, ceiling and floor materials are suitable for use with steam and hot condensation, the steam produces. 2. Unit may be installed up to 50 feet away from steam room and 6 feet away from the steam distribution unit in a dry well ventilated area. 3. Use copper or brass fittings only (NEVER USE GALVANIZED FITTINGS). 4.
PAGE 5
Generator Installation Instructions Parts Enclosed      Steam generator Installation Instructions Warranty card User Warning Label Smitty Pan All ThermaSol steam generators are designed to build NO PRESSURE during operation. This is for your safety. Note: Failure to follow installation instructions specifically will cause the warranty to be void.
PAGE 6
Generator Installation Instructions (con’t) Materials Needed             Brass ball valve (for water supply shut off) Pipe compound Copper or brass fittings & nipples (sizes and quantities per instructions) In-line water filter (recommended) 3/8” brass or copper union 1/2” brass or copper union Wire (sizes and quantities per instructions) Copper tubing or pipe Wire cap nuts Flex conduit Silicone Other materials as required Tools Needed            Pipe wrench Tubing cutter Wire cutt
PAGE 7
UP TO FOUR ROOMS Figure 3 Note: The generator must be mounted level with all connections on top. !!!!! IMPORTANT !!!! LOCATE THE STEAM HEAD 6” INCHES BELOW CEILING AND 6 INCHES FROM NON BENCHED/SEATED/DOOR INTERIOR WALL CORNER. STEAM HEAD IS TO BE MOUNTED AS FAR AS POSSIBLE FROM TYPICAL BATHING POSITION (SEATED OR STANDING) AND AS FAR FROM CONTROL AS POSSIBLE WHILE MAINTAINING APPROXIMATELY A – 60” CONTROL HEIGHT.
PAGE 8
Electrical Installation Note: All electrical wiring must be done per National/Local Electrical Codes. ** ThermaSol requires that a licensed electrician perform all electrical work. ** Note: USE COPPER WIRE ONLY. Wire sizes recommended by NEC (2002 Version). Minimum wire temperature rating 90C. Type THHN.
PAGE 9
CONSUMER WARNING WARNING DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH. WARNING NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON POSITION. SEVERE BURNS WILL OCCUR. WARNING STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS “ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF.
PAGE 10
Steam Distribution System - Requirements for Proper Installation 1. Turn off all electricity to the working area at the main breaker panel! 2. Ensure the steam rooms to be used are vapor proof. They should have a vapor proof door that seals well so the steam does not escape. Make sure the walls, ceiling and floor materials are suitable for use with steam and hot condensation, the steam produces. 3.
PAGE 11
Steam Distribution System Installation Instructions All ThermaSol Steam Distribution Systems are designed to build NO PRESSURE during operation. This is for your safety. Note: Failure to follow installation instructions specifically will cause the warranty to be void. Note: The DS-SDS must be mounted vertically with all connections on top.
PAGE 12
Steam Distribution System Installation Instructions (con’t) Materials Needed        Pipe compound Copper or brass fittings & nipples (sizes and quantities per instructions) Wire (sizes and quantities per instructions) Copper tubing or pipe Wire cap nuts Silicone Other materials as required Tools Needed           Pipe wrench Tubing cutter Wire cutters or wire strippers Adjustable wrench Screwdrivers (phillips & regular) Solder & Flux 1-1/16” masonry drill bit Drill motor Propane torch Oth
PAGE 13
STEAM HEAD INSTALLATION Parts Enclosed   Deluxe steam head Escutcheon Tools Needed     Pipe wrench 7/8” cutting tool Silicone gun Other tools as required IMPORTANT NOTE! Locate the steam head 6" from any corner, 12" from the floor, and as far away as possible from any bench, seat or door. The steam head is to be mounted as far away as possible from typical bathing positions (seated or standing) and as far away from the room temperature sensor as possible. 1.
PAGE 14
CONSUMER WARNING WARNING DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH. WARNING NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON POSITION. SEVERE BURNS WILL OCCUR. WARNING DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH YOUR ALLERGIST OR DOCTOR BEFORE USE.
PAGE 15
Day Spa Control Installation Instructions 1. The Day Spa Time & Temp digital control must be located inside the shower area. 2. Install the touch pad 4 to 6 feet from the floor inside the steam room. Drill a 1-1/16” hole in the wall. 3. Bring the control cable from the Steam Distribution System (DS-SDS) through the 1-1/16” hole. Using the coupler, connect the cable to the touch pad connector. Ensure the coupler is located higher in the wall than the control.
PAGE 16
Day Spa Control Operating Instructions continued, WARNING: Please consult your physician before using this steam bath if you are pregnant, elderly, have high blood pressure, diabetes, suffering from heart disease, intoxicated, or in poor health. 1. Starting Your Steam Bath. Press the “Control Button” momentarily to activate your steam bath session.
PAGE 17
4. Manual Power Off. To manually power off the generator before the selected time has expired, press the “Control Button” once. The LED’s will go off and the steam will turn off. (Figure 10) Note: The Day Spa TT control has a built in memory and will remember your time and temperature setting for the next session. Depress once to turn off. Generator before timer expires Figure 10 5. Diagnostic Feature. The Day Spa TT control has a unique diagnostic feature.
PAGE 18
(Optional) Day Spa Sentinel Installation Instructions 1. The Day Spa Sentinel (Figure 13) can be located anywhere within 100 ft of the Steam Distribution System (DS-SDS). 2. Install the Sentinel display 2 to 6 feet from the floor on a wall. Drill a 1-1/16” hole in the wall. 3. Bring the control cable from the Steam Distribution System (DS-SDS) through the 1-1/16” hole. Using the coupler, connect the cable to the Sentinel connector. Ensure the coupler is located higher in the wall than the Sentinel.
PAGE 19
Day Spa Sentinel Installation Instructions continued, 6. THE FOLLOWING STEPS MUST BE TAKEN OR YOUR WARRANTY WILL BE VOID. Coat the entire sentinel back with supplied waterproof silicon. Completely seal the sentinel to the wall to create a moisture barrier. Place the sentinel on the wall pressing firmly. You may need to tape the sentinel into place until the silicone dries. Be careful not to harm the wall and / or sentinel with the tape (Figure 13). Let dry for 24 hours before using.
PAGE 20
Figure 14 PAGE 21 CONTAINS IMPORTANT WARRANTY RETURN INSTRUCTIONS Please complete the DAY SPA WARRANTY REGISTRATION CARD information on the following page. Please ensure to include all information requested on the card.
PAGE 21
DAY SPA 5 YEAR "NO QUESTIONS ASKED" – FACTORY WARRANTY ThermaSol will repair the specific failure on your ThermaSol DAY SPA Series Steam generator manufactured after February 1, 2006 at its factory for 5 years. All expenses required to remove and send the unit to the factory, return and reinstall the unit is the responsibility of the owner. EXCLUSION I.