Operation Manual

ManualsBrandsTheben ManualsBackupLUXA 102-140 LED

1. Basic safety instructions

2. Description

Danger of death through electric shock or fire!

 Installation should only be carried out by a qualified electrician!

WARNING

• The device conforms with EN 60598-1 if correctly installed

• IP 44 in accordance with EN 60598 and IEC 62471 (Photo biological

security of lamps and lamp systems)

Designated use

• LED spotlight for automatic lighting control

• Suitable for installation on external walls

• Suitable for corridors, gardens, entrances, parks etc.

• For use in normal ambient conditions

Disposal

Dispose of spotlight in an environmentally sound manner

(electronic waste).

2 pins for setting

time (TIME) and

brightness (Lux)

Motion detector

with lens

Adjustable LED

spotlight (with 4

LEDs)

LUXA 102-140 LED 8W WH 1020971

LUXA 102-140 LED 8W BK 1020972

LUXA 102-140 LED 16W WH 1020973

LUXA 102-140 LED 16W BK 1020974

LUXA 102-140 LED 8W W WH 1020951

LUXA 102-140 LED 8W W BK 1020952

LUXA 102-140 LED 16W W WH 1020953

LUXA 102-140 LED 16W W BK 1020954

309565 02

LED spotlight with motion detector

Summary of content (8 pages)

PAGE 1
309565 02 GB LED spotlight with motion detector LUXA 102-140 LUXA 102-140 LUXA 102-140 LUXA 102-140 LUXA 102-140 LUXA 102-140 LUXA 102-140 LUXA 102-140 LED LED LED LED LED LED LED LED 8W WH 8W BK 16W WH 16W BK 8W W WH 8W W BK 16W W WH 16W W BK 1020971 1020972 1020973 1020974 1020951 1020952 1020953 1020954 1.
PAGE 2
. Connection WARNING Warning, danger of death through electric shock!  Disconnect power source.  Ensure device cannot be switched on!  Check power supply is disconnected.  Earth and bypass.  Cover or shield any adjacent live components. 3. Installation 240V 0FF  Disconnect power source.  Loosen catch mechanism with a screwdriver and remove motion detector from base. Ø 6 mm Screws MOUNTING 60mm  Fix socket to wall.
PAGE 3
external conductor LIVE brown BROWN neutral BLUE NEUTRAL blue conductor mains EARTH earth green/ GREEN / yellow YELLOW  Feed the cable through the opening and connect the individual wires to the appropriate terminal.  Plug motion detector into base. 230 V 0N  Connect device to mains. The device need 40 seconds to warm up. CAUTION!  High temperature! Do not touch the metal parts of the device.
PAGE 4
Installation instructions As the detector reacts to variations in temperature, avoid following situations:  Do not direct motion detectors at objects with highly-reflective surfaces such as mirrors etc.  Do not install motion detectors near heat sources such as heating outlets, air conditioning systems, lamps etc.  Do not direct the motion detector at objects that move in the wind such as curtains, large plants etc.  Take account of motion direction during test run.
PAGE 5
4. Direction test and alignment The direction test serves to identify the appropriate installation site for the best possible detection range. The LED spotlight only reacts to movement (independent of brightness)  Set the time pin to T.  Switch on device.  Go diagonally to the detection area. Once the device has detected a movement, the lamps light up for 2 seconds.  Note direction of motion during the test.
PAGE 6
5. Setting The motion detector has two pins underneath for setting the time (TIME) and brightness (LUX). 1. Setting the time (TIME)  Set the desired time of 5 s – 10 min using the pin. After each movement, the LED switches on for the desired length of time. 2.Setting light level (lux)  Set desired function: moon for complete darkness or sun for full brightness. Desired brightness can be set as required between the two. Brightness setting Time setting 5sec 0 5 sec 10min 0 Min 10 3.
PAGE 7
LEDs are on at night LEDs are on in the day and at night CAUTION! 24 Hrs 6. Use screens  Use supplied screen to adjust the motion detector to desired detection area.  Remove the required section from the screen using pliers.  Then place on the lens and screw in.
PAGE 8
7. Technical data • Operating voltage: • Frequency: • Standby: • Lamp type: • Detection angle: • Detection range: • Installation height: • Brightness setting range: • Power-on time range: • Permissible ambient temperature: • Protection class: • Protection rating: 100–240 V~ 50-60 Hz max. 0.5 W LED (1 x 8 W, 430 lm / 2 x 8 W, 860 lm) (not dimmable) 140 ° (2 m); 90 ° (10 m) max. 10 m 1.8–2.