User's Manual

ManualsBrandsTexas Instruments ManualsElectronicsThe CC1180DB is a development tool for TIs sub 1 GHz CC1180 chip.

SWRU276a

October 2012

1/3

CC1180DB Nodes

CC430 Node

Edge Router

(Gateway)

CC430 Node

CC1180EM

Adapter Card

Green LED

Switch S7-2

SD Card slot

CC-6LOWPAN-DK-868 Quick Start Guide

STEP 1 – Introduction

This guide describes how to set up a CC-6LOWPAN-DK-868 development kit using

the pre-programmed devices of the CC-6LOWPAN-DK-868 Kit.

The 6LoWPAN development kit is designed to give a simple

introduction to 6LoWPAN wireless networks in the 868/915MHz bands. The

hardware consists of an OMAP-L138 based Edge Router equipped with

a CC1180EM, 2 CC430F5137 based nodes and 2 CC1180DB nodes.

The CC1180DB boards consist of a network processor (CC1180)

pre-programmed with a 6LoWPAN software stack, and a MSP430F5438A

microcontroller that controls the 6LoWPAN device.

The CC430 based nodes consists of a CC430F5137 SoC (RF+MCU) that

runs both the 6LoWPAN software stack and the controlling application.

The Edge Router board is running Linux and is pre-programmed with

Sensinode Nanorouter 2.0 software, which acts as a bridge between IPv6

and 6LoWPAN. The Edge Router is connected to a PC via Ethernet. The

Edge Router sets up the network and configures the 6LoWPAN network

parameters.

The development kit demonstrates an example of a typical sensor network with a simple Network Analyzer software

running on the nodes. The nodes are automatically given a unique IPv6 address and can be pinged from a PC using

standard tools. Each node in the 6LoWPAN network also has a unique preprogrammed IEEE address.

The battery powered nodes can act as routers that on request report their key data to the Edge Router.

STEP 2 – Install the PC software and connect the Edge Router

Install the Windows IPv6 stack on a Windows XP PC. The IPv6 installation is not needed in Linux and Windows 7, since

IPv6 is already installed.

Open a command prompt and write ipv6 install

Assign the IPv6 address 2001::22 to the PC using the command prompt: (Run in administrator mode in Windows 7)

netsh interface ipv6 add address “Local Area Connection” 2001::22

Set up a default route using the command prompt: (Run in administrator mode in Windows 7)

netsh interface ipv6 add route ::/0 “Local Area Connection”

Note! You must change “Local Area Connection” to the actual name of the Ethernet connection you want to use. You can

get it from Windows Network Connections. The IPv6 address 2001::22 has to be unique on your network.

Plug in the power cable to the Edge Router and connect the Ethernet cable between the Edge Router and the PC. Make

sure that the Edge Router is not powered on.

Insert the SD card into the slot on the Edge Router.

Connect the CC1180EM to the

adapter card and connect an antenna

to the CC1180EM.

Connect the adapter card to the J30

connector on the Edge Router. The

adapter card can be fastened to the

Edge Router by the provided M2

screws.

Make sure that the switch S7-2 is in position ON,

and all other in position OFF.

Power on the Edge Router using the S4 switch.

It will take approximately 40 seconds to boot the Edge Router. When the green LED on the Adapter Card goes ON it

indicates that the Edge Router is up and running. You can connect the provided RS-232 NULL modem cable between

the Edge Router and PC to get debug information, use e.g. Windows HyperTerminal with settings; Baud Rate 115200, 8

Data Bits, No Parity, One Stop Bit and No Flow Control.

Summary of content (7 pages)

PAGE 1
SWRU276a October 2012 CC-6LOWPAN-DK-868 Quick Start Guide STEP 1 – Introduction This guide describes how to set up a CC-6LOWPAN-DK-868 development kit using the pre-programmed devices of the CC-6LOWPAN-DK-868 Kit. CC1180DB Nodes The 6LoWPAN development kit is designed to give a simple introduction to 6LoWPAN wireless networks in the 868/915MHz bands. The hardware consists of an OMAP-L138 based Edge Router equipped with a CC1180EM, 2 CC430F5137 based nodes and 2 CC1180DB nodes.
PAGE 2
SWRU276a October 2012 STEP 3 – Connecting the nodes to the 6LoWPAN network Insert batteries in one or more of the CC1180DB boards and make sure the jumper is connected between P1-1 and P1-2 to power on the node. It will automatically connect to existing network. LEDs D1 and D2 are controlled from the CC1180 network processor and gives status on node connection. When the CC1180DB node is connected to the network the green LED (D2) will be on, if not connected it will be off.
PAGE 3
SWRU276a October 2012 The Low Power RF Online Community has forums, blogs and videos. Use the forums to find information, discuss and get help with your design. Join us at www.ti.com/lprf-forum STEP 6 – More Information Caution! The kit contains ESD sensitive components. Handle with care to prevent permanent damage. To minimize risk of injury, avoid touching components during operation if symbolized as hot.
PAGE 4
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions: The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods.
PAGE 5
FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
【Important Notice for Users of this Product in Japan】】 This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product: 1. 2. 3. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.
PAGE 7
EVALUATION BOARD/KIT/MODULE (EVM) WARNINGS, RESTRICTIONS AND DISCLAIMERS For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished electrical equipment and not intended for consumer use.