TRN-TABLET3 MODEL: TRN-TABLET3 15.6" Tablet PC with Intel® Core™ i7-7820EQ CPU, 16 GB DDR4 SDRAM, USB 3.0, HDMI, 1 TB M.2 SSD, Wi-Fi, Bluetooth, 5-Megapixel Camera, RoHS Compliant User Manual Page i Rev. 1.
TRN-TABLET3 Revision Date Version Changes February 11, 2020 1.01 Spec. modification February 11, 2019 1.
TRN-TABLET3 Copyright COPYRIGHT NOTICE In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved.
TRN-TABLET3 Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product. NOTE These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.
TRN-TABLET3 Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 FEATURES ................................................................................................................... 3 1.3 FRONT PANEL...................................................................................
TRN-TABLET3 4.3.4 ACPI Settings ................................................................................................... 28 4.3.5 iWDD H/W Monitor ......................................................................................... 29 4.3.5.1 Smart Fan Mode Configuration ................................................................ 30 4.3.6 USB Configuration........................................................................................... 32 4.4 CHIPSET ..........................
TRN-TABLET3 List of Figures Figure 1-1: TRN-TABLET3 .............................................................................................................2 Figure 1-2: Front Panel ..................................................................................................................3 Figure 1-3: Rear Panel ....................................................................................................................4 Figure 1-4: Top Panel .............................................
TRN-TABLET3 List of Tables Table 1-1: Technical Specifications ..............................................................................................7 Table 2-1: Packing List .................................................................................................................10 Table 4-1: BIOS Navigation Keys ................................................................................................
TRN-TABLET3 BIOS Menus BIOS Menu 1: Main .......................................................................................................................22 BIOS Menu 2: Advanced ..............................................................................................................23 BIOS Menu 3: CPU Configuration ...............................................................................................24 BIOS Menu 4: SATA Configuration ....................................................
TRN-TABLET3 Chapter 1 1 Introduction Page 1
TRN-TABLET3 1.1 Overview Figure 1-1: TRN-TABLET3 The TRN-TABLET3 is a 15.6" tablet PC with the Intel® Core™ i7-7820EQ processor and 16 GB DDR4 SDRAM. Its storage needs are met by the preinstalled 1 TB M.2 SSD. In addition, an NVIDIA® Quadro® P3000 MXM graphics card can be installed to enhance graphics processing capability. The TRN-TABLET3 is integrated with a selection of wireless communication technologies, including Wi-Fi and Bluetooth. There are four external USB 3.
TRN-TABLET3 1.2 Features Some of the standard features of the TRN-TABLET3 tablet PC include: Intel® Core™ i7-7820EQ processor platform 16 GB DDR4 SDRAM NVIDIA® Quadro® P3000 MXM graphics card (optional) 10-point projected capacitive touchscreen Built-in 5-megapixel camera Built-in stereo speakers and digital microphone 802.11a/b/g/n/ac wireless LAN Bluetooth v4.0 One HDMI and four USB 3.0 ports (three Type-A and one Type-C) on the side panel RoHS compliant 1.
TRN-TABLET3 1.4 Rear Panel The rear panel has a battery pack and a 2-in-1 stand that can turn into a carrying handle. The two speakers are also located on the rear panel. Figure 1-3: Rear Panel 1.5 Top Panel The power button (with power LED) is located on the top panel as shown in the following diagram. To power-up the system, short press the power button, and the power LED on the button lights up in blue.
TRN-TABLET3 1.6 Side Panel The right side panel contains several I/O interfaces as shown below.
TRN-TABLET3 1.7 Technical Specifications The TRN-TABLET3 technical specifications are listed in the table below. Display LCD Size 15.6" Brightness (cd/m2) 400 Max. Resolution 1920 (H) x 1080 (V) Viewing Angle 88/88/88/88 degree (wide viewing angle, IPS) Touchscreen 10-point projected capacitive System CPU Intel® Core™ i7-7820EQ Memory 16 GB DDR4 SDRAM OS Windows 10 Pro Storage 1 TB M.
TRN-TABLET3 Power Power Adapter AC Input: 100 V AC ~ 240 V AC DC Output: 19 V @ 10.53 A, 200 W External: 6500 mAH Li-ion battery pack with battery Battery capacity LED indicators, 10.
TRN-TABLET3 1.
TRN-TABLET3 Chapter 2 2 Unpacking Page 9
TRN-TABLET3 To unpack the TRN-TABLET3, follow the steps below: WARNING! Only remove the protective plastic cover stuck to the front screen after installation. The plastic layer protects the monitor surface during installation process. Step 1: Use sharp cutters to open the external and internal boxes. Step 2: Lift the TRN-TABLET3 and the packing material out of the box. Step 3: Make sure all the components listed in the packing list are present.
TRN-TABLET3 Chapter 3 3 Installation Page 11
TRN-TABLET3 3.1 Safety Precautions Please ensure the following safety precautions are adhered to at all times. To prevent the risk of electric shock, make sure power cord is unplugged from wall socket. To fully disengage the power to the unit, please disconnect the power cord from the ac outlet. Refer servicing to qualified service personnel. The AC outlet shall be readily available and accessible. Follow the electrostatic precautions outlined below whenever the TRN-TABLET3 is opened.
TRN-TABLET3 3.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the TRN-TABLET3 may result in permanent damage to the TRN-TABLET3 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TRN-TABLET3. Dry climates are especially susceptible to ESD.
TRN-TABLET3 Anti-static Discharge: If a user open the rear panel of the TRN-TABLET3, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband. 3.
TRN-TABLET3 Step 2: Install the battery pack as shown in Figure 3-2. 406H4 77H Figure 3-2: Battery Pack Installation Step 3: To charge the battery, connect the TRN-TABLET3 with a power source through the supplied power adapter. Step 4: To view the battery capacity, press the battery capacity button on the battery (Figure 3-3).
TRN-TABLET3 Step 5: To remove the battery pack, press the two buttons indicated in the following diagram at the same time to eject the battery jack. CAUTION: Do not remove the battery pack while the TRN-TABLET3 is on and running.
TRN-TABLET3 3.5 Using the 2-in-1 Stand The 2-in-1 stand secured on the rear panel can stabilize the TRN-TABLET3 on a surface, and also can be turned into a carrying handle. Stand Adjust the 2-in-1 stand to have a best angle to operate the system (see Figure 3-5). Figure 3-5: Tablet Stand Carrying Handle Adjust the 2-in-1 stand to the upright position to use it as a handle (see Figure 3-6).
TRN-TABLET3 3.6 VESA Mounting The TRN-TABLET3 is VESA (Video Electronics Standards Association) compliant and can be mounted on a mounting device with a 75 mm interface pad. The TRN-TABLET3 VESA mount retention screw holes are shown in Figure 3-7. Refer to the installation guide that came with the mounting device to mount the TRN-TABLET3.
TRN-TABLET3 Chapter 4 4 BIOS Setup Page 19
TRN-TABLET3 4.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice. 4.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1.
TRN-TABLET3 Key Function Page Up Move to the previous page Page Dn Move to the next page Esc Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F2 Load previous values F3 Load optimized defaults F4 Save changes and Exit BIOS Table 4-1: BIOS Navigation Keys 4.1.
TRN-TABLET3 4.2 Main The Main BIOS menu ( BIOS Menu 1) appears when the BIOS Setup program is 430H510 H804 H entered. The Main menu gives an overview of the basic system information. Main Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced Chipset Security Boot Save & Exit BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time American Megatrends 5.12 UEFI 2.6; PI 1.4 Z484AR01.
TRN-TABLET3 System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 4.3 Advanced Use the Advanced menu ( BIOS Menu 2) to configure the CPU and peripheral devices 43 1H511H 805H through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
TRN-TABLET3 4.3.1 CPU Configuration Use the CPU Configuration menu ( BIOS Menu 3) to view detailed CPU specifications 432H5 12H8 08H and configure the CPU. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced CPU Configuration Type Intel(R) Core(TM) i7-7820EQ CPU @ 3.
TRN-TABLET3 Intel (VMX) Virtualization Technology [Enabled] Use the Intel (VMX) Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time. Disabled Enabled Disables Intel Virtualization Technology. DEFAULT Enables Intel Virtualization Technology.
TRN-TABLET3 4.3.2 SATA Configuration Use the SATA Configuration menu ( BIOS Menu 4) to change and/or set the 434H514H8 10H configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced SATA Configuration Enable/Disable SATA Device. SATA Controller(s) SATA Mode Selection [Enabled] [AHCI] M2_M1 Slot M.2 (S80) 3MG2 (496.1GB) --------------------: Select Screen : Select Item Enter: Select +/-: Change Opt.
TRN-TABLET3 4.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced TPM20 Device Found Security Device Support Pending Operation [Enable] [None] Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
TRN-TABLET3 4.3.4 ACPI Settings The ACPI Settings menu ( BIOS Menu 6) configures the Advanced Configuration and 873H806H Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S3 (Suspend to RAM)] Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. ---------------------: Select Screen : Select Item Enter: Select +/-: Change Opt.
TRN-TABLET3 4.3.5 iWDD H/W Monitor The iWDD H/W Monitor menu ( BIOS Menu 7) shows the operating temperature. 436H 516H 814H Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select. CPU temperature System temperature Ultrasound temperature :+60 °C :+51 °C :+0 °C CPU_FAN1 Speed SYS_FAN1 Speed :1543 RPM :5528 RPM CPU_CORE +5V VCCIO +DDR +5VSB +3.3V +3.3VSB :+0.997 :+5.023 :+0.920 :+1.190 :+5.038 :+3.310 :+3.
TRN-TABLET3 o o o o o VCCIO DDR +5VSB +3.3V +3.3VSB 4.3.5.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 8) to configure the system fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
TRN-TABLET3 The following options can only be set if the CPU/SYS Smart Fan Control option is set to Auto Mode. Auto mode fan start temperature If the CPU temperature is between fan off and fan start, the fan speed change to fan start PWM. To set a value, Use the + or – key to change the value or enter a decimal number between 1 and 100. Auto mode fan off temperature If the CPU temperature is lower than the value set this option, the fan speed change to be lowest.
TRN-TABLET3 4.3.6 USB Configuration Use the USB Configuration menu ( BIOS Menu 9) to read USB configuration 435H515 H811H information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced USB Configuration USB Devices: 1 Keyboard, 1 Mouse, 1 Point Legacy USB Support [Enabled] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
TRN-TABLET3 Enabled Disabled Legacy USB support disabled Auto Legacy USB support disabled if no USB devices are DEFAULT Legacy USB support enabled connected 4.4 Chipset Use the Chipset menu ( BIOS Menu 10) to access the PCH and System Agent (SA) 437H 519H8 17H configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
TRN-TABLET3 4.4.1 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 11) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset System Agent (SA) Configuration VT-d Memory Configuration Parameters Supported > Memory Configuration > PEG Port Configuration VT-d [Enabled] --------------------: Select Screen : Select Item Enter: Select +/-: Change Opt.
TRN-TABLET3 4.4.1.1 Memory Configuration Use the Memory Configuration menu (BIOS Menu 12) to display the memory information. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset Total Memory 16384 MB DIMM1 DIMM2 8192 MB (DDR4) 8192 MB (DDR4) --------------------: Select Screen : Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2018 American Megatrends, Inc.
TRN-TABLET3 Enable Root Port [Auto] Use the Enable Root Port option to enable or disable the PCI Express (PEG) controller. Disabled Disables the PCI Express (PEG) controller. Enabled Enables the PCI Express (PEG) controller. Auto DEFAULT PCI Express (PEG) controller is automatically detected and enabled. Max Link Speed [Auto] Use the Max Link Speed option to select the maximum link speed of the PCI Express slot.
TRN-TABLET3 PCIe Speed [Auto] Use this option to select the support type of the PCI Express slot (M2_A1). The following options are available: Auto Gen1 Gen2 Gen3 Default Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to configure whether to detect if a non-compliance PCI Express device is connected to the PCI Express port. Disabled DEFAULT Do not detect if a non-compliance PCI Express device is connected to the PCI Express port.
TRN-TABLET3 4.5 Security Use the Security menu ( BIOS Menu 15) to set system and user passwords. 440 H523 H821H Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
TRN-TABLET3 4.6 Boot Use the Boot menu ( BIOS Menu 16) to configure system boot options. 439H522H 820H Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Bootup NumLock State Quiet Boot [On] [Enabled] Boot Option Priorities Boot Option #1 [PO:M.
TRN-TABLET3 Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Disabled Enabled Normal POST messages displayed DEFAULT OEM Logo displayed instead of POST messages Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices. Disabled Enabled DEFAULT Ignore all PXE Option ROMs Load PXE Option ROMs.
TRN-TABLET3 Hard Drive BBS Priorities Use the Hard Drive BBS Priorities option to set the order of the legacy devices in this group. 4.7 Save & Exit Use the Save & Exit menu ( BIOS Menu 17) to load default BIOS values, optimal failsafe 441H524H 822H values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
TRN-TABLET3 Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
TRN-TABLET3 Appendix A A Regulatory Compliance Page 43
TRN-TABLET3 DECLARATION OF CONFORMITY This equipment is in conformity with the following EU directives: EMC Directive (2014/30/EU) Low-Voltage Directive (2014/35/EU) RoHS II Directive (2011/65/EU, 2015/863/EU) If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply. If this equipment has telecommunications functionality, it also complies with the requirements of the R&TTE Directive 1999/5/EC.
TRN-TABLET3 Español [Spanish] IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
TRN-TABLET3 Româna [Romanian] IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE. Slovensko [Slovenian] IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
TRN-TABLET3 FCC WARNING This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
TRN-TABLET3 ROHS STATEMENT The label on the product indicates this product conforms to European (EU) Restriction of Hazardous Substances (RoHS) that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. CHINA ROHS The label on the product indicates the estimated “Environmentally Friendly Use Period” (EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.
TRN-TABLET3 Appendix B B Product Disposal Page 49
TRN-TABLET3 CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
TRN-TABLET3 Appendix C C Maintenance and Cleaning Precautions Page 51
TRN-TABLET3 When maintaining or cleaning the TRN-TABLET3, please follow the guidelines below. WARNING: If you dropped any material or liquid such as water onto the tablet when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable. CAUTION: For safety reasons, turn-off the power switch and unplug the tablet before cleaning. Do not scratch or rub the screen with a hard object.
TRN-TABLET3 C.1.2 Cleaning Tools Some components in the TRN-TABLET3 may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the TRN-TABLET3. Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the TRN-TABLET3.
TRN-TABLET3 Appendix D D Symbol Definitions Page 54
TRN-TABLET3 The following symbols appear on the product, its labeling, or the product packing. Each symbol carries a special definition, as defined below: This side up Consult the operating instructions Fragile, handle with care Keep dry Refer to instruction manual Indicates the manufacturer Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities.
TRN-TABLET3 Appendix E E BIOS Options Page 56
TRN-TABLET3 Below is a list of BIOS configuration options in the BIOS chapter. System Date [xx/xx/xx] ........................................................................................................22 System Time [xx:xx:xx] .......................................................................................................23 Active Processor Cores [All] ..............................................................................................
TRN-TABLET3 Boot Option #1 [PO:M.2 (S80) 3MG-P] ...............................................................................40 Hard Drive BBS Priorities....................................................................................................41 Save Changes and Reset ....................................................................................................41 Discard Changes and Reset ...............................................................................................
TRN-TABLET3 Appendix F F Hazardous Materials Disclosure Page 59
TRN-TABLET3 The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only. A label will be placed on each product to indicate the estimated “Environmentally Friendly Use Period” (EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.
TRN-TABLET3 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 O O O O O O 显示 O O O O O O 印刷电路板 O O O O O O 金属螺帽 O O O O O O 电缆组装 O O O O O O 风扇组装 O O O O O O 电力供应组装 O O O O O O 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 (现由 GB/T 26572-2011 取代)
