HD Conference Camera User Manual ShenZhen Tenveo Video Technology Co,.ltd www.hktenveo.com Headquarter (ShenZhen) Xi'an Branch Add.: Rm 638-639, Block B, Tianhui Add.: Rm 2302, Block A, Zhongdeng building, No 106, Yousong Rd, Lon- Wenjing building, Fengcheng 9th Rd, ghua Dist, Shenzhen, China. Weiyang Dist, Xi'an, China. E-mail: sales@tenveo.com Email: sherry@tenveo.com Mobile: +86-18929337105 Tel: +86-29-81318040 Version V5.
Contents Product Description Foreword ------------------------------------ Notice ------------------------------------ Supplied Accessories ------------------------------------ 1 1 1 Performance Characteristics Tech parameters ------------------------------------ Camera papameters ------------------------------------ 2 2 Quick Start Interface definition ------------------------------------ Interface diagram ------------------------------------ 3 3 Installation instructions ----------------
Attention 1. Foreword Thanks for choosing our VHD series conference cameras. Please read this manual carefully before using the product. 2. Notice ·To avoid damage from stress, violent vibration, soaking during transportation, storage and installation. ·Take care of each components of camera during installation, and install camera at where is affordable enough, to avoid drop or scratches of camera case. ·Handle the camera parts gently, do not squeeze the camera units hard.
Performance Characteristics 1. Camera technical parameters Electric Input Voltage Communication Baud DC12V Power Protocol 12W Decoder Operation Vertical Rotation Rotation Speed VISCA/PELCOD/P Address Set internal Horizontal Rotation 2400/4800/9600bps 0~255 Surroundings Operating Environment Operating Temp ±170° 120° 0°~+50° 0~95% 100°/s non-condensing Physics Installation Method 9 remote controls Preset Point Pelco Protocol 256 Net-Weight 1.
Quick Start 1. Interface definition A B NO IR USB RS-232 RS-485 1234 IR SELECT DC 12V ① ② ③ ④ ⑤ ⑥ 1.IR 2.USB 3.RS-232 4.RS-485 5.IR SELECT 6.DC12V 2.
3.Installation instructions (1)Surface Installation Put the camera on the desk flat, and make sure the camera in level. If want to put the camera on oblique surface, please make sure the angle of inclination less than 15 degree for ensure camera pan and tilt working in normal operation. _ 15° < _ 15°> (2) Tripod Mount Installation Twist the tripod’s screw on the camera tripod hole, then the tripod could be installed on the bottom of camera. The tripod screw must fit below.
Remote control button description (1)Remote Control Launch Window (2)【POWER】Standby Button, pressing it, camera goes into Standby Mode; pressing again, camera goes Power ON. (3)【P/T Reset 】Camera Pan/Tilt reset Function same with⑧(P/T RESET) (4)【CAMERA SELECT】Choose the camera number that needed to control, to correspond the dial-up code on the back of camera; (5)【POSITION】Preset position setup keys, include 【PRESET】and【RESET】. Press PRESET+NUMNER: to setup preset; Press RESET+NUMBER: to clear preset.
Common Operations Introductions CAMERA SELECT 1. Camera Select 1 2 3 Refer to the dial-up at the back of camera and choose camera address number that you want to control(1-3)。 2. Camera Direction Control Turning up Turning down HOME Turning to left Turning to right *Note: Press direction key to move the camera.Press the direction key when you need to change the angle.
4. Camera Zoom Control Press any one of the 4【ZOOM】 to make the zoom functioning. + + ZOOM SLOW ZOOM FAST - - 5. Back Light The subject will become dark when there is a light source behind it, press【BACK LIGHT】 B-LIGHT to use back light shooting function. To cancel, press【BACK LIGHT】again. 1 6.
PS: RS-422/485 and RS232 Pins distribution 1、Control Interface (1)RS485 Interface Distribution PIN NUM FUNCTION A DTR IN+(connect to RS-485) B DSR IN+(connect to RS-485) (2) RS-232 Interface Distribution 2、Remote Control Match CAMERA SELECT 1 2 3 Set camera's remote control address. Point the arrow to 1, Short press 1 on camera select to select the camera 1. Point the arrow to 2, Short press 2 on camera select to select the camera 2.
Troubleshooting Before request service to serviceman, it can according to below methods to remove failures, ifstill can’ t be solved, please contact us for help. Q:The video of camera cannot be displayed on the screen. A:Please check the connection between power cable,video cable, camera and monitor, fix the connector on each end. Q: It’ s unable to Pan, Tilt and zoom camera. A:Because menu was displayed on monitor. Please re-operate after exit menu.
Te n v e o Wa r r a n t y C a r d Thank you very much for choosing our products. User ‘s info: Name: Email: Tel: Post code: Address: Product’ s information: Product Name : Factory Serial Number : Purchase Date Attention: 1.This card is considered as the Protection to fix warranty, so please reserve them carefully.Please fill in truthfully. 2. Please indicate the model number, Factory Serial Number and the detailed description of the fault information.
Certificate of Tenveo compliance Q.A.
Make any meeting better and easier