HD Conference Camera User Manual Version V3.
Contents Product Description Foreword ------------------------------------ Notice ------------------------------------ Supplied Accessories ------------------------------------ 1 1 1 Performance Characteristics Tech parameters ------------------------------------ Camera papameters ------------------------------------ 2 2 Interface definition ------------------------------------ 3 Interface diagram ------------------------------------ 4 ------------------------------------ 4 Quick Start
Attention 1. Foreword Thanks for choosing our VHD series conference cameras. Please read this manual carefully before using the product. 2. Notice ·To avoid damage from stress, violent vibration, soaking during transportation, storage and installation. ·Take care of each components of camera during installation, and install camera at where is affordable enough, to avoid drop or scratches of camera case. ·Handle the camera parts gently, do not squeeze the camera units hard.
Performance Characteristics 1. Camera technical parameters Electric Input Voltage Communication Baud DC12V Power Protocol 12W Decoder Operation 0~64 Surroundings Operating Environment Operating Temp ±175° Vertical Rotation 120° Rotation Speed VISCA/PELCO-D/PELCO-P Address Set internal Horizontal Rotation 9600/38400bps 0°~+50° 0~95% 100°/s non-condensing Physics Installation Method Preset Point: 9 remote control, Preset Point for256 for PELCO, 64 for VISCA. Net-Weight 1.
Quick Start 1. Interface definition 1.Pan&Tilt POWER 2.Stand by indicator STANDBY 3.IR remote indicator 4.
2.Interface diagram USB RS232 RS-485 DC 12V USB RS232 RS-485 3.Installation instructions (1)Surface Installation Put the camera on the desk flat, and make sure the camera in level. If want to put the camera on oblique surface, please make sure the angle of inclination less than 15 degree for ensure camera pan and tilt working in normal operation.
Remote control button description (1)Remote Control Launch Window (2)【POWER】Standby Button, pressing it, camera goes into Standby Mode; pressing again, camera goes Power ON. (3)【P/T Reset 】Camera Pan/Tilt reset Function same with⑧(P/T RESET) (4)【CAMERA SELECT】Choose the camera number that needed to control, to correspond the dial-up code on the back of camera; (5)【POSITION】Preset position setup keys, include 【PRESET】and【RESET】.
★Attentions for Remote Control 1. If remote control doesn't work, please replace batteries. 2. If there is an object between remote control and specialized remote control sensor, the camera will not work. Please make sure the remote control is aimed at the sensor which in front of the camera when controlling it. 3 L/R SET and Menu keys are not applicable for this model. 4 Fast zoom key, slow zoom key, manual and auto focus keys not applicable for fixed focus model.
【AUTO】Switch the focus mode to AUTO 【MANUAL】Switch the focus mode to MANUAL 【FAR】Far focus manually FAR NEAR 【NEAR】Near focus manually *Note:not applicable for fixed focus model. 4. Camera Zoom Control Press any one of the 4【ZOOM】 to make the zoom functioning. These 4 keys are not applicable for fixed focus camera. MANUAL FOCUS AUTO FOCUS + + ZOOM SLOW ZOOM FAST - 1 5.
2.Dial-up SW1(1,2,3,4,5,6): Baud rate set SW1 DIP-2 DIP-3 PTZ Add. DIP-1 DIP-4 DIP-5 DIP-6 1 ON OFF OFF OFF OFF OFF 2 .... OFF ON OFF OFF OFF OFF 64 ON ON ON ON ON ON 3.Dial-up SW2(1/2/3): Protocol set Protocol VISCA PELCO-D DIP-1 OFF OFF SW2 DIP-2 OFF ON PELCO-P ON OFF Baud 9600 38400 DIP-3 OFF ON 4.Dial-up 3 IR transfer(IR PASS), DIP-4 reserve IR Add.
Troubleshooting Before request service to serviceman, it can according to below methods to remove failures, ifstill can’ t be solved, please contact us for help. Q:The video of camera cannot be displayed on the screen. A:Please check the connection between power cable,video cable, camera and monitor, fix the connector on each end. Q: It’ s unable to Pan, Tilt and zoom camera. A:Because menu was displayed on monitor. Please re-operate after exit menu.
Te n v e o Wa r r a n t y C a r d Thank you very much for choosing our products. User ‘s info: Name: Email: Tel: Post code: Address: Product’ s information: Product Name : Factory Serial Number : Purchase Date Attention: 1.This card is considered as the Protection to fix warranty, so please reserve them carefully.Please fill in truthfully. 2. Please indicate the model number, Factory Serial Number and the detailed description of the fault information.
Certificate of compliance Q.A.
Make any meeting better and easier