Install 800mm disk head assembly

ManualsBrandsTennant ManualsMachinesRide-On Floor Scrubber

IB 340755 (01--2007) 1

No. 340755

Machine: T7/SSR

Published: 01--2007

Rev. 00

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual p arts and will save th e cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9000142

SYNOPSIS:

This kit contains the parts needed to install the 800mm disk head assembly on T7/SSR machines.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PREPARATIO N:

1. Empty the solution and recovery tanks. Refer

to the Operators Manual for instructions.

2. Park the machine on a clean level surface and

if necessary raise the scrub head. Turn off the

machine.

3. Remove the brushes from the machine.

4. T urn on the machine and lower the scrub

head and squeegees.

5. T urn off the machine and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off the

machine, and remove the key.

6. Disconnect the battery cables from the

batteries.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

7. Jack or lift the front end of the machine

between 6” and 12” from the floor, slide the

jack stands underneath the machine, and

lower the machine onto the jack stands. Refer

to the Operators Manual for instructions.

FOR SAFETY: When servicing machine, block

machine tires before jacking up machine. Use

a hoist or jack capable of supporting the

weight of the machine. Jack machine at

designated locations only. Support machine

with jack stands.

8. Disconnect the cables from both scrub head

drive motors and the wires and hose from the

water solenoid valve. Refer to Fig. 1.

Disconnect

motor

cables from

main wire

harness

Disconnect wires

and hose from

solenoid valve

FIG. 1

9. Remove the hardware (A) holding the scrub

head to the machine and slide the scrub head

from under the machine. Set the hardware

aside. Refer to Fig. 2.

10. Remove the lift arms (B) from the scrub head.

Set the lift arms and hardware (C) aside.

Refer to Fig. 2.

Summary of content (4 pages)

PAGE 1
INSTRUCTION BULLETIN No. 340755 Machine: T7/SSR Published: 01--2007 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
Actuator A Remove hardware (A) (not shown) from this side of machine also A A A A C C C B C FIG. 2 11. Remove the center arm plates (D) and the scrub head lift spring (E) from the scrub head. Set center arm plates, scrub head lift spring, and all hardware (F) aside. Refer to Fig. 3. 12. Remove the lift bracket (G) from the scrub head. Set the lift bracket and hardware (H) aside. Refer to Fig. 3. F D E D F F F H G F F FIG.
PAGE 3
INSTALLATION: 1. Use the saved hardware (H) to install the lift bracket (G) onto the new scrub head (1). Refer to Fig. 3. 2. Use the saved hardware (C) to install the lift arms (B) onto the new scrub head (1). Refer to Fig. 2. 3. Use the saved hardware (F) to install the center arm plates (D) and scrub head lift spring (E) onto the scrub head (1). Refer to Fig. 3. 5. Connect all hoses, wires, and cables disconnected from the old scrub head to the new scrub head (1). Refer to Fig. 1. 6.
PAGE 4
Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Ref. 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 TennantPart No. 1013599 1017910 1017832 1015989 1017495 1017462 222504 86859 1010876 1017785 1011344 1011334 1011317 1011717 1011719 49694 222505 1017534 1017653 09010 32691 Description Valve, Water, Solenoid, 24vdc, 10bm/10bm ) Support Wldt, Sqge, RH Retainer, Sqge, RH Pin, Hitch, .312d X 1.62l Sleeve, P/M, 0.496d 0.318b 1.375 SS Block, Guard Screw, Hex, M8 X 1.