Update Wire Harness Water Solenoid Valve Connection

ManualsBrandsTennant ManualsMachinesBattery-Powered Ride-On Floor Scrubber

IB 9016476 (11- 2017) 1

INSTRUCTION BULLETIN

No. 9016476

Machine: See Synopsis

Published: 11- 2017

Rev. 00

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts an d will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9016477

SYNOPSIS:

This kit contains the parts needed to update the wire harness on M20 / T20 / M30 / M17 / T17

machines to be equipped with a newer model solenoid water valve.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PROTECT THE ENVIRONMENT

Please dispose of packaging mat er ials, us ed machine component s

such as bat t er ies and f luids in an env ironm ent ally saf e way ac cor ding

to local w ast e disposal regulat ions.

Always remember to recycle.

PREPARATIO N:

NOTE: The following instructions can be used to

update the wire harness on both the main scrub

head and the scrubbing side brush.

1. Remove the brush(es) from the main scrub

head and the scrubbing side brush. Set the

brush(es) aside.

2. Disconnect the battery cable(s) from the

machine.

3. Turn on the machine, completely lower the

main scrub head / scrubbing side brush, and

turn off the machine.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

4. Disconnect the battery cable(s) from the

machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

5. Remove any other parts / components

necessary to access the solenoid water

valves located on the main scrub head /

scrubbing side brush assembly.

INSTALLATION:

1. Cut the spade terminals from the ends of the

wires previously connected to the old water

solenoid valve. Cut as close to the spade

terminals as possible.

2. Strip approximately 0.375 in. (9.5 mm) of

insulation from the end of each wire from the

previous step.

3. Cut the leads on the electrical harness (1) to

length.

4. Strip approximately 0.375 in. (9.5 mm) of

insulation from the end of each electrical

harness (1) wire.

Summary of content (7 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9016476 Machine: See Synopsis Published: 11- 2017 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
5. Crimp a sealed butt connector (2) onto each electrical harness (1) wire. (Fig. 1) 8. Connect the electrical harness (1) to the water solenoid valve. (Fig. 5 / Fig. 6 / Fig. 8) 9. Use a cable tie to secure the electrical harness (1) to the frame of the machine and away from any moving parts that could possibly damage the electrical harness. To help prevent moisture from getting into the connector / wire connections, loop the electrical harness. (Fig. 3 / Fig. 4) FIG. 1 6.
PAGE 3
M20 / T20 / M30 Main Scrub Water Solenoid Valve From solution tank Solenoid water valve. Note Duetsch DT04- 2P connector To main scrub head FIG.
PAGE 4
M20 / T20 / M30 Side Scrub Water Solenoid Valve (Optional) From solution tank Solenoidwatervalve. Note Duetsch DT04- 2P connector To scrubbing side brush FRONT FIG.
PAGE 5
Cut existing spade connectors from main wire harness connections previously connected to water solenoid valve. Cut wires on electrical harness to length and use sealed butt connectors (2) to install electrical harness (1) onto wires previously connected to old water solenoid valve. M20 / T20 / M30 Side Scrub Water Solenoid Valve (Optional) Main Scrub Water Solenoid Valve FIG.
PAGE 6
M17 / T17 From solution tank Cylindrical scrub head Existing water solenoid valves replaced with new water solenoid valve equipped with Duetsch connector FRONT From solution tank Disk scrub head FIG.
PAGE 7
M17 / T17 Main Scrub Water Solenoid Valve Cut existing spade connectors from main wire harness connections previously connected to water solenoid valve. Cut wires on electrical harness to length and use sealed butt connectors (2) to install electrical harness (1) onto wires previously connected to old water solenoid valve. FIG. 9 Bill Of Materials For Connector Kit, DT06- 2S - 9016477 Tennant Ref. Part No.