Install Telemetry (IRIS) Kit (Europe Install)

ManualsBrandsTennant ManualsMachinesBattery-Powered Ride-On Floor Scrubber

IB 9014047 (12- 2019) 1

INSTRUCTION BULLETIN

No. 9014047

Machine: T17 (Europe)

Published: 12- 2019

Rev. 00

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9014023

Kit installation must be performed by TennantTrue



service or an authorized service provider.

SYNOPSIS:

This kit contains the parts needed to install the telemetry kit onto T17 scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 2 - 3 hours)

The IRIS (telemetry module) must be activated to complete this installation. Module will not

function until it is activated. Call local IRIS expert for assistance activating module after all

telemetry components have been installed. Have machine serial number and IRIS module SIM

number (located on back of IRIS control box assembly) ready when calling for activation.

PROTECT THE ENVIRONMENT

Please dispose of pack aging mat erials , used mac hine component s

such as batt eri es and f luids in an env ironm ent ally saf e way ac cor ding

to local wast e dis posal regulat ions .

Always remember to recycle.

PREPARATIO N:

1. Confirm the hour meter is properly wired and

functional. The hour meter must be fully

functional and properly wired before the IRIS

system can be installed.

2. Stop the machine on a level surface and turn

off the machine.

3. Remove the brushes from the main scrub

head. Set the brushes aside.

4. Machines equipped with cylindrical

brushes only: Remove the debris trough

from the back of the scrub head.

5. T urn on the machine, completely lower the

scrub head, turn off the machine, set the

parking brake, and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, set parking brake, and remove key.

6. Evaluate the condition of batteries, cables,

and terminal connections. Batteries /cables/

terminal connections must all be in safe

working condition.

7. Disconnect the battery cable from the

machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

Summary of content (11 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9014047 Machine: T17 (Europe) Published: 12- 2019 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
8. Remove the battery from the machine. FOR SAFETY: When servicing machine, use a non- conductive battery removal device, use a hoist and adequate assistance when lifting batteries, battery installation must be done by trained personnel, follow site safety guidelines concerning battery removal. 9. Remove the SEMS M6 hex screws securing the electrical enclosure cover to the electrical enclosure. Set the SEMS M6 hex screws aside. (Fig. 1) 11.
PAGE 3
8 FRONT 20 22 21 14 18 19 11 13 9 12 10 15 To: Machine ground To: B+ @ M1 To: Telemetry control box/main wire harness To: Telemetry control box FIG. 5 3. Use the M8 hex screws (21) and three cable clamps (20) to secure the battery cable (14) to the battery cover. (Fig. 6) 4. Route the battery cable (14) to the shunt (9). (Fig. 7) FIG. 7 FIG.
PAGE 4
5. Slide a terminal boot (12) onto the battery cable (14) black cable and connect the black cable to the shunt (9). (Fig. 5) 6. Slide a terminal boot (12) onto the black cable (15) and connect the black cable to the shunt (9). (Fig. 5) 7. Route the battery cable (14) red cable and the black cable (15) down toward the floor and then up along the frame of the machine to the hole in the electrical compartment. (Fig. 8/ Fig. 9) 8.
PAGE 5
11. Insert a cable tie clip (16) into the frame of the machine. (Fig. 12) 14. Connect the telemetry harness (13) to the main wire harness. (Fig. 12/Fig. 19) 12. Use four M5 hex screws (3), four flat washers (4), and four M5 hex lock nuts (5) to install the telemetry control box (1) onto the telemetry bracket (2). (Fig. 12) 15. Use a cable tie (17) to secure the telemetry harness (13) to the cable tie clip (16) previously inserted into the frame of the machine. (Fig. 12) 13.
PAGE 6
INSTALLATION TIP: Secure a thin gauge wire, approximately the length of the telemetry harness (13), to the end of the telemetry harness to be connected to the shunt (9) and route the wire with the telemetry harness. This wire can then be secured to the the antenna (8) wire to help route the antenna wire along the telemetry harness to the telemetry control box (1). 17.
PAGE 7
Main wire harness FIG.
PAGE 8
41 mm (1.62 in.) 89 mm (3.50 in.) 83 mm (3.25 in.) 6.35 mm (0.25 in.) Location for mounting battery charger cable connector FIG. 19 21. Drill two 6.35 mm (0.25 in.) holes into battery compartment cover. Do Not drill up into the top surface of the battery compartment cover. (Fig. 19) 23. Route the antenna (8) wire through the cable clamps (20), along the main battery cable (14) /telemetry harness (13), and to the telemetry control box (1). (Fig. 21) 22.
PAGE 9
24. Connect the antenna (8) wire to the telemetry control box (1). (Fig. 22) 28. Start the machine, raise the scrub head, and turn off the machine. 29. Reinstall the brushes into the main scrub head. 30. Machines equipped with cylindrical brushes only: Reinstall the debris trough onto the scrub head. 31. Start and test the machine. 32. Activate the IRIS (telemetry module): Call local IRIS expert for assistance to activate the module. The IRIS telemetry system must be activated to complete installation.
PAGE 10
8 20 22 21 14 18 19 11 13 12 9 10 15 FRONT 17 6 7 16 2 5 1 3 4 FIG.
PAGE 11
Bill Of Materials For Telemetry Kit, CI [T17, Intl/EU] - 9014023 o Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 Y 14 15 16 17 18 19 20 21 22 Tennant Part No. 1070541 1207701 24199 01683 06549 01684 08712 1070658 1070757 06927 07514 611221 1073059 9009990 1074600 1074601 1071085 130773 32483 33930 69234 09740 1210807 Description Controlbox Assy, Telem [Int] Bracket Wldt, Mtg, Telem Screw, Hex, M5 X 0.80 X 16, SS Washer, Flat, 10, SS Nut, Hex, Lock, M5 X 0.80, Nl Washer, Flat, 0.27b 0.69d .