Install Strobe Light Kit

ManualsBrandsTennant ManualsMachinesBattery-Powered Ride-On Floor Scrubber

IB 9012975 (05- 2016) 1

INSTRUCTION BULLETIN

No. 9012975

Machine: T17 / M17

Published: 05- 2016

Rev. 01

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9020109

SYNOPSIS:

This kit contains the parts needed to install a strobe light kit onto T17 scrubbers /

M17 sweeper- scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 2 hours)

PROTECT THE ENVIRONMENT

Please dispose of pack aging mat erials , used mac hine component s

such as batt eri es and f luids in an env ironm ent ally saf e way ac cor ding

to local wast e dis posal regulat ions .

Always remember t o recycle.

PREPARATIO N:

1. Park the machine on a clean level surface,

turn off the machine, set the parking brake,

and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, set parking brake, and remove key.

2. Disconnect the battery cable from the

machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

INSTALLATION:

1. Remove the hole cover label from the

recovery tank cover. (Fig. 1)

Recovery

tank cover

Hole cov er

label

FIG. 1

Summary of content (10 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9012975 Machine: T17 / M17 Published: 05- 2016 Rev. 01 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
. Use two pan screws (20) to install each LED light assembly (19) onto the light module cover (18). (Fig. 2) 5. Install the circuit breaker boot (22) onto one 2.5 Amp circuit breaker (8). (Fig. 4) 4 22 18 9 19 6 5 7 2 8 20 FIG. 2 FIG. 4 3. Use two M5 pan screws (14), two flat washers (15), and two M5 hex nuts (16) to install the strobe light (1) onto the light module base (2). (Fig. 3) 6. Use a cable tie (9) to secure the 2.
PAGE 3
FIG. 6 - Alarm / Light Wire Harness 11. Route the alarm / light wire harness (10) 9. Connect the alarm / light wire harness (10) to through the channel in the recovery tank the light (1), backup alarm (4), 2.5 Amp circuit cover and to the battery compartment. breaker (8), and both LED light assemblies Connect the alarm / light wire harness to the (19). (Fig. 4 / Fig. 5 / Fig. 6) main wire harness. (Fig. 8 / Fig. 6 / Fig. 10) 10. Plug the 36VDC relay (21) into the alarm / light wire harness (10). (Fig.
PAGE 4
FIG.
PAGE 5
FIG.
PAGE 6
FIG.
PAGE 7
17 Remove and discard hole blank. Install switch (17) into switch location Set pan screws aside Control panel Front shroud FIG. 12 NOTE: Complete Step 13 through Step 18 only if machine is not equipped with the optional front light kit. The switch (17) is already installed on machines equipped with the optional front light kit. 13. Remove the pan screws holding the control panel to the front shroud and set the pan screws aside. (Fig. 12) 16.
PAGE 8
Access panel Circuit breaker bracket Set hardware aside Set hardware aside FIG. 14 19. Remove the access panel from the steering channel. Set the hardware aside. (Fig. 14) 20. Remove the M8 hex screws securing the circuit breaker bracket to the machine. Set the hardware aside. (Fig. 14) 21. Pull circuit breaker bracket out far enough to access the main wire harness connectors located behind the bracket. Do not break any connections to the other circuit breakers when pulling the bracket from the machine.
PAGE 9
20 18 17 19 FRONT 14 1 12 20 22 6 8 8 7 4 5 21 9 2 13 15 16 3 11 10 FRONT FIG.
PAGE 10
Bill Of Materials For Light Kit, Strobe, Module CI [T17] - 9020109 o Yo YY YY Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Tennant Ref. Part No.