Install Rollout Battery (DI)

ManualsBrandsTennant ManualsMachinesBattery-Powered Ride-On Floor Scrubber

IB 9012976 (07- 2016) 1

INSTRUCTION BULLETIN

No. 9012976

Machine: T17 / M17

Published: 07- 2016

Rev. 01

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9020156 (T17 machines NA serial numbers 000000- 010999 /

EU serial numbers 0000- 0330) / 9014965 (T17 machines NA serial numbers 011000- /

EU serial numbers 0400- ) (All M17 machines)

SYNOPSIS:

This kit contains the parts needed to install the optional rollout battery kit on T17 scrubbers /

M17 sweeper- scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PROTECT THE ENVIRONMENT

Please dispose of pack aging mat erials , used mac hine component s

such as batt eri es and f luids in an env ironm ent ally saf e way ac cor ding

to local wast e dis posal regulat ions .

Always remember t o recycle.

PREPARATIO N:

1. Park the machine on a clean level surface,

turn off the machine, set the parking brake,

and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, set parking brake, and remove key.

2. Disconnect the battery cable from the

machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

3. Remove the battery from the machine.

FOR SAFETY: When servicing machine, use a

non- conductive battery removal device, use a

hoist and adequate assistance when lifting

batteries, follow site safety guidelines

concerning battery removal, and battery

installation must be done by trained

personnel.

Summary of content (6 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9012976 Machine: T17 / M17 Published: 07- 2016 Rev. 01 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
. Use one M5 socket screw (15) and one M5 hex nut (16) to install the limit switch (14) onto the rollout battery channel (1). (Fig. 1) INSTALLATION: NOTE: The rollout battery channel (1) weighs approximately 85 lbs (39 kg). Assistance is required for lifting the rollout battery channel. Do Not attempt to lift the rollout battery channel without assistance. 3.
PAGE 3
5 4 2 17 1 13 16 3 14 8 6 8 9 7 18 9 10 12 6 9 7 6 11 11 9 7 15 4. Use three M8 flat screws (3), three flat washers (4), and three M8 hex nuts (5) to install of the three plastic plates (2) into the rollout battery channel (1). (Fig. 2) IB 9012976 (07- 2016) FIG. 2 5. Use four M8 hex screws (13) to install the rollout battery assembly assembled in the previous steps into the battery compartment. (Fig.
PAGE 4
6. Connect the main wire harnes to the rollout battery limit switch (14). (Fig. 3 / Fig. 4) FIG.
PAGE 5
TO: GROUND TO: BATTERY FIG.
PAGE 6
7. Reinstall the battery into the machine and reconnect the battery cable to the machine. FOR SAFETY: When servicing machine, use a non- conductive battery removal device, use a hoist and adequate assistance when lifting batteries, follow site safety guidelines concerning battery removal, and battery installation must be done by trained personnel. 9. Start and test the machine: Turn on the machine, place the directional switch in the forward direction, and press the propel pedal.