Install Deluxe Seat Kit

ManualsBrandsTennant ManualsMachinesBattery-Powered Ride-On Floor Scrubber

IB 9012972 (05- 2016) 1

INSTRUCTION BULLETIN

No. 9012972

Machine: T17 / M17

Published: 05- 2016

Rev. 01

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9020103

SYNOPSIS:

This kit contains the parts needed to install a deluxe seat kit onto T17 scrubbers /

M17 sweeper- scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PROTECT THE ENVIRONMENT

Please dispose of pack aging mat erials , used mac hine component s

such as batt eri es and f luids in an env ironm ent ally saf e way ac cor ding

to local wast e dis posal regulat ions .

Always remember t o recycle.

PREPARATIO N:

1. Park the machine on a clean level surface,

turn off the machine, set the parking brake,

and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

2. Disconnect the battery cable from the

machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

3. Remove the battery from the machine.

FOR SAFETY: When servicing machine, use a

non- conductive battery removal device, use a

hoist and adequate assistance when lifting

batteries, follow site safety guidelines

concerning battery removal, and battery

installation must be done by trained

personnel.

INSTALLATION:

1. Disconnect the main wire harness from the

seat switch.

2. Remove the upper platform from the machine.

Set all mounting hardware aside. (Fig. 1)

3. Remove the existing seat from the machine.

Discard the seat, both slide tracks, and all

mounting hardware. (Fig. 1)

Summary of content (4 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9012972 Machine: T17 / M17 Published: 05- 2016 Rev. 01 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
Remove operator seat from upper platform. Discard operator seat, both slide tracks, and hardware. Upper platform Remove hex screws (Qty. 4) and flat washers (Qty. 4) securing seat to upper support. Discard removed hardware. Remove M4 SEMS hex screw securing platform mounting plate located on bottom of upper platform to lower platform. Set M4 SEMS hex screw aside. Remove M4 SEMS hex screws securing seat support angles located on bottom of upper platform to support bracket. Set M4 SEMS hex screws aside.
PAGE 3
1 Upper platform 4 2 5 3 7 FRONT 6 FIG. 2 4. Use two pan screws (5) and two spacers (4) to install the seat slide track with the latch (2) and the seat slide track (3) onto the deluxe operator seat (1). (Fig. 2) 5. Use four hex nuts (6) and four flat washers (7) to install the deluxe operator seat assembly assembled in the previous step onto the upper platform. (Fig. 2) IB 9012972 (05- 2016) 6. Reinstall the upper platform onto the machine. 7.
PAGE 4
8. Reinstall the battery into the battery compartment. FOR SAFETY: When servicing machine, use a non- conductive battery removal device, use a hoist and adequate assistance when lifting batteries, follow site safety guidelines concerning battery removal, and battery installation must be done by trained personnel. 10. Test the machine. Place the directional switch in either forward or reverse. With no pressure on the operator seat, turn on the machine and press the propel pedal. The machine should not move.