LTE CPE12300XG Quick Installation Guide
1 Introduction This Quick Installation Guide covers the basic installation of the CPE12300XG Outdoor. Overview The CPE12300XG is a category 12 LTE UE designed to provide wireless Internet access for a home or small office. Before you Begin Check the following items in this package: CPE Package: No.
2 2 PoE Injector 1 3 Bracket 2 4 U shape bolt for ≤2" 2 5 Nut M6 8
3 6 SEMS Screw M6x12mm 8 Getting to know the CPE Note: The figures below are provided only for reference purposes. See the actual product for more details.
4 PWR Blue Level 0-LED Off SINR < 1 ON Device is Powered On Off Device is Powered Off Ethernet connection is established. Ethernet connection is not established ON ETH Blue Off SIM ON SIM card is inserted/ detected Off SIM card is not detected/Inserted Blue Placing the CPE Place the CPE outdoors facing open area and eNodeB. Obstructions such as concrete walls, glass partitions or wooden walls affect the transmission and reception of wireless signals.
5 To mount the CPE to wall, follow the steps below (left to right) as described in the next paragraph: Connecting the CPE Install the USIM card This CPE is specially designed for the 4G LTE network. Please check that you have a valid USIM card from the service provider. 1. Open the USIM Card Slot lid. 2. Insert a valid USIM card into the USIM card slot.
6 3. Connect Ethernet cable. 4. Put the lid cover back. Remove the USIM card Open SIM Slot Lid cover and Push USIM card to eject it from the slot. Connecting External Device(s) to the CPE To use the Internet connection and configure the CPE settings, you must connect your CPE to a computer. 1. Insert the other end of the Ethernet cable to the port of the POE power supply (Port marked POE) to be kept inside the premises near the AC outlet. 2.
7 The web based utility of the CPE is a web browser based configuration interface that allows easy device set up, configuration and management through internet browser. For example: on a PC with Windows XP or higher version: 1. 2. Connect the hardware of the CPE correctly. Set the IP address of the connected computer and ensure that the IP address of the computer is in the same segment as that of CPE. Note: By default the IP address of the CPE is 192.168.254.251, the subnet mask is 255.255.255.
8 FAQ: The power indicator is not ON. Check if the POE Power Supply is plugged properly into AC socket. Check if the LED on the POE power supply is Green indicating it is correctly plugged in AC. Check if the power adapter meets the requirement and specification. Check if the Ethernet Cable used to carry power to CPE is a four pair cable. Web Based Utility cannot be accessed Ensure that the CPE is powered on.
9 Device cannot access the internet Check that Operator has provided internet access services. Check that IP address is automatically taken. Check that firewall rules are not blocking your internet service. Throughput performance is not OK Ensure that there are not too many users under the same LTE Cell. Ensure the wireless environment is good. Check the value of SINR thru GUI. >10 dB is a good value for good throughput. FCC Regulations: This device complies with part 15 of the FCC Rules.
10 -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information This device meets the government’s requirements for exposure to radio waves.
11 ISED Notice This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
12 Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR102 définies pour un environnement non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 50 cm (20 pouces) pendant le fonctionnement normal.
