EcoSwitch Installation Guide SS8030 Company Headquarters: Telkonet, Inc. 10200 W. Innovation Dr. Suite 300 Milwaukee, WI 53226 Support Information: Toll Free: +1 (800) 380 9640 Email: support@telkonet.com Sales Information: Toll Free: +1 (888) 703 9398 Email: sales@telkonet.
Table of Contents Table of Contents Table of Contents ....................................................................................................................i Installation Requirements .......................................................................................................... 1 Required Equipment ............................................................................................................. 1 Electrical Requirements .................................................
Installation Requirements Installation Requirements Required Equipment EcoSwitch (P/N: SS8030) Flathead screwdriver for mounting and unmounting wall plate Wire nuts Voltmeter Electrical Requirements Before installation, ensure that the EcoSwitch will be connected to a line with the following electrical properties: LINE Type LINE Voltage LINE Frequency Alternating Current (AC) 120 Volts (V) 60 Hertz (Hz) Before installation, ensure that the devices controlled by the EcoSwitch use less than the f
Installation Requirements Regulatory Compliance FCC Notice This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Wiring the EcoSwitch Wiring the EcoSwitch 1. 2. 3. 4. 5. 6. Turn the power off at the circuit breaker. Unmount the existing switch cover plate. Unmount the existing switch from the junction box. Use the voltmeter to verify the power is off. Disconnect the existing switch from its wiring. Use the table below to determine which wires are the 120V LINE, GROUND, and NEUTRAL IN from the – breaker panel. 7.
Wiring the EcoSwitch 14. Verify all wire connections. The wires should now look like Figure 1. If only one Neutral connection was available, the wires will look like Figure 2.
Wiring the EcoSwitch 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. Turn the power on at the circuit breaker. Press the switch once. Verify the switch clicks and the light fixture turns on. Press the switch once. Verify the switch clicks and the light fixture turns off. Turn the power off at the circuit breaker. Mount the EcoSwitch into the junction box. Mount the switch cover plate. Turn the power on at the circuit breaker. Wiring is complete.
Associating the EcoSwitch with an EcoInsight Associating the EcoSwitch with an EcoInsight Connect the EcoSwitch to the ZigBee Network 1. Determine which EcoConnect will provide the ZigBee network for the EcoSwitch. The same EcoConnect must be used for both the EcoInsight and the EcoSwitch. 2. Activate joining on the EcoConnect using the EcoCentral Virtual Engineer web interface or by pressing the recessed button on the EcoConnect’s front plate.
Associating the EcoSwitch with an EcoWave (EcoAir + EcoSource) Associating the EcoSwitch with an EcoWave (EcoAir + EcoSource) Connect the EcoSwitch to the ZigBee Network 1. Determine which EcoConnect will provide the ZigBee network for the EcoSwitch. The same EcoConnect must be used for both the EcoSource and the EcoSwitch. 2. Activate joining on the EcoConnect using the EcoCentral Virtual Engineer web interface or by pressing the recessed button on the EcoConnect’s front plate.
Troubleshooting Troubleshooting Issues Connecting the EcoSwitch to the ZigBee Network Problem Potential Cause Potential Solution After pressing and holding the EcoSwitch for 10 seconds, the LED is solid green. The EcoSwitch was not held down continuously for 10 seconds. Wait 5 seconds and try again. After pressing and holding the EcoSwitch for 10 seconds, the LED rapidly blinks red. The sensor is unable to locate an EcoConnect in Joining mode. Reactivate joining on the EcoConnect and try again.