User's Manual

ManualsBrandsTelkonet ManualsElectronicsOccupancy Sensor

Table Of Contents

6.70.104 SS2000 / SS2200 Association Procedures 5/2010

Confidential – Information contained in this document is considered proprietary and confidential, and is intended for the internal

use of Telkonet, Inc. our contracted Partners and VARs, and customers. This content is protected by all applicable copyright

Technical Note 6.70.104

SS2000 / SS2200 Association Procedures

Scope: This document provides the process by which a SS2000 / SS2200 Occupancy Sensor is

Associated to an SS1107 PTAC Controller or SS5000 / SS5200 Thermostat

NOTE: This document applies only

to the SS1107 PTAC Controller variant and SS5000 / SS5200

rev 4.5 and 5.1 Thermostat Models.

Authors: Teejay Riedl, Robert Zirpoli

Revision History:

Revision Number Date Changed By: Summary of Change

1 12/2282008 Teejay Riedl / Robert

Zirpoli

Initial Draft

2 03/09/09 Teejay Riedl Audit Cycle

3 03/30/09 Teejay Riedl Merged data for SS5K

association

4 06/16/09 Teejay Riedl Update

5 10/2009 Teejay Riedl Update; new

numbering

6 5/27/2010 Robert Zirpoli Edited to include

SS2200

Contents

Overview ...................................................................................................... 2

Terminology: ............................................................................................. 2

Preparation:.................................................................................................. 2

Procedures: SS2000 to SS1107 Controller ......................................................... 2

Step One – Power the Controller ................................................................... 2

Step Two – Initiate the Association................................................................ 2

Procedures: SS2000 to 5000 Thermostat........................................................... 4

Step One – Power the Thermostat................................................................. 4

Step Two – Initiate the Association................................................................ 5

Step Three – Confirm the Association ............................................................ 6

Summary of content (6 pages)

PAGE 1
6.70.104 SS2000 / SS2200 Association Procedures 5/2010 Technical Note 6.70.104 SS2000 / SS2200 Association Procedures Scope: This document provides the process by which a SS2000 / SS2200 Occupancy Sensor is Associated to an SS1107 PTAC Controller or SS5000 / SS5200 Thermostat NOTE: This document applies only to the SS1107 PTAC Controller variant and SS5000 / SS5200 rev 4.5 and 5.1 Thermostat Models.
PAGE 2
6.70.104 SS2000 / SS2200 Association Procedures 5/2010 Overview This document describes the process to associate (i.e. link) an SS2000 / SS2200 to either an SS1107 or SS5000 / SS5200. The document is separated by base-station type (SS1107 and SS5000 / SS5200).
PAGE 3
6.70.104 SS2000 / SS2200 Association Procedures 3. 4. 5/2010 After approximately 30 seconds, the LED will indicate the relative signal strength as red, yellow, or green. Yellow or Green are acceptable levels. If a red signal is shown, relocate the sensor to a better location. Poke the 1107. The sensor LED will now blink to indicate the number of sensors which are associated to it.
PAGE 4
6.70.104 SS2000 / SS2200 Association Procedures 5/2010 Procedures: SS2000 / SS2200 to SS5000 / SS5200 Thermostat Unlocking the Command Mode NOTE: In some cases, depending on the installation and previous deployment, the SS5000 / SS5200 may have its command buttons “locked” to prevent tampering. If the procedures in “Step One” below do not allow control of the thermostat, follow these steps to unlock the Command functions 1 . 1. 2. Press and hold the Fan button for ~7-10 seconds.
PAGE 5
6.70.104 SS2000 / SS2200 Association Procedures 5/2010 Step One – Power the Thermostat 1. 2. Apply Power to the unit Set the Thermostat to “Learn” mode: a. Lift the front cover to expose the front panel buttons. b. Push the % button three times in a row. c. The display will read 00 d. Press the Up Arrow until the display reads 02, then push the % button again. “2” represents the command to associate Sensors. e. The display will change to Learn Mode, showing -0 then any number from 0 to 9.
PAGE 6
.70.104 SS2000 / SS2200 Association Procedures 5/2010 Figure 3 : Thermostat showing Signal Strength from Sensor 7. 8. Observe the signal strength. The desired value is anywhere from 5 to 9. If a lower value is shown, re-position the sensor and test. Do not deploy a Sensor to a location yielding a signal strength less than 5. If associating multiple Sensors, press the % button while the Thermostat is still in Learn Mode. The Thermostat will display a number from 0-9. Repeat steps 5 – 7 above.