Quick Reference Door lock/status check/illumination Door unlock ~~ Remote engine start/shut down Emergency panic alarm activation/ turn off Vibration mode Garage door JJCH2 Indoor temperature check (Not available in US Model} Proximity door lock Press SET button for 3 sec. function On/Off’ Vehicle finding Press SET [J button B® Programmed engine start Press SET 0 butter function ON/OFF Trunk release Press SET [1 button 1H Personal alarm On/Off Press SET 0 MODE Temporary hold of Press SET [1 PRIG for 3 sec.
Vehicle Alarm & Engine Starter System Vehicle Alarm & Immobilizer Remote & Programmable Engine Start Lifestyle Enhancing Convenience features LCD screen illumination Vibration of Remote Control INTRODUCTION Congratulation on your purchase of the BOOMERANG Vehicle Alarm & Starter System! The BOOMERANG System features state-of-the-art technology for maximum safety and satisfaction.
tapping impact to the Remote Control (for paging the driver), and a temperature sensor which takes the temperature of the passenger compartment for display on the LCD screen of the Remote Control, Brief took at each device 1-6. Remote Control The Remote Control consists of TX/RX electronic circuits, LCD screen, quartz clock, melody buzzer and a vibrator. Three rectangular buttons at the bottom of the LCD screen are used io program the System.
communication, may also delay the signal transmission. For instance, if a signal from TX part is sent to the RX part of the Main Control Module while it is in sleep mode, the RX part may not recognize the signal sent by TX part for a few seconds until the RX part is in wake up mode and vise versa, For the same reason, when you shut down any of the System's operation and get no response with your first press of a button, we recommend pressing the button again after waiting several seconds. 2-2.
.. H you press button B the LCD screen illuminates for approximately five seconds, You can program each function by checking corresponding graphic icon or figures displayed on the LCD screen. Arming Mode Your vehicle is in arming mode. Personal Alarm You have set morning call alarm. Valet Mode All the factions are temporarily on hold. Vibration Mode Remote Control vibrates when the System is triggered.
2. Press button With-one chirp sound, tur signal lights flash one time. 4, Doors are locked and vehicle shall be in arming status in approximately ten seconds. one chirp 0 oo one flash Lock Flash Eyeball moves to right and left in arming status To shut down the alarm sound, press button [Hor 22. It is recommended to press the button in between beeps on the Remote Control to make sure of shut-down.
1 the turn signal lights flash four times with four chirp sounds *. when you unlock/disarm the vehicle with the Remote Control, it means that ong of the doors was forced to open while you were out of transmission range. 1£ the turn signal lights flash three times with three chirp sounds ‘when you unlock/disarm the door with the Ra mote Control, it means that the Shock Sensor was triggered while you were out of transmission range.
3-6, Vibration meed This is useful when you are in 8 noisy place and it is difficult to hear beep sound from the Remote Control. In this mode, the Remote Control vibrates if your vehicle is tampered with, 1. Press and hold down button PRIG for approximately three seconds. 2. The Remote Control will be in vibration mode and, on the LCD screen, the 777 icon displays. T's return to sound mode, press.and hold down button PRIG for approximately three seconds, 3-7.
3-10, System's status check When you want to check the System's present status on the LCD screen, press button approximately two seconds in arming status. With one melody sound, the LCD screen illuminates approximately five seconds. By pressing button A approximately two seconds, you can also check if your Remote Control is within range of transmission or not. If within the range, a light melody sound emits with 777 icon displayed on the LCD screen. If you are out of range, five warning beeps emits. 3-11.
2.Press button SET. 3.Press button PRIG for approximately three seconds. 4.With a chirp sound, 77? icon displays on the LCD screen. To cancel or release from the valet mode, repeat above steps. ‘With two chirp sounds, the System returns to normal status, Alarm functions 4-1, Alarm by door, hood or trunk open sensing The System goes into arming status if you lock the doors after exit from your vehicle and arm the System with Remote Control after the elapsed preset delay time.
about the emergency state of the triggered alarm, Therefore, in secret, you can immediately detect any unauthorized violation to your armed vehicle. This will also eliminates potential ‘false’ alarms which can be a nuisance in a residential area. 4-4, Engine start disable in arming status (optional) If this optional feature is incorporated, the vehicle's engine will not start, in arming status, even with your ignition key.
2. With one chirp sound, turn signal lights flash one time to confirm that the starter motor will start in approximately six seconds, 3. With three chirps, engine starts to run. During the remote start time, tum signal lights continue flashing every two seconds. From the Remote Control, an icon showing the gas emission flashes on the LCD screen and melody sound emits every two minutes to remind you of running engine.
4. The engine shuts down immediately and the System is now ready for next remote (or programmable) engine start. Ta cancel above prior memorization process for the remote or programmed engine start sequence, Pull off the ignition key while the driver's side door is opened and the dome light stays turned on. Then, the engine shuts down immediately and prior-memorization for the next engine start is canceled.
morning or when the vehicle is parked beyond the range of the Remote Control. To set or cancel the function, your vehicle should be within the range of transmission from the Remote Control and also should be in arming status with all the doors locked. 1. Before set-up of programmed engine start, you should set your time for engine start(0) See 7-2, page 7727) 2 Press button SET in arming status with all the doors locked.
This is useful in the event that someone wants to page the driver of the parked vehicle, If someone tries to page you by tapping the Paging (knock) Sensor which is usually mounted on the bottom part of the front window, the paging melody sound continues sounding from your Remote Control and ‘CALL indication flashes on the LCD screen. 1, To shut down the paging melody sound from the Remote Control, press button tis recommended to press the button while the melody sound from the Remote Control is on hold.
of the Communication Module. If you turn the screw clockwise, the range of activation gets longer; turn counter-clock wise, the range gets shorter. To disable this function, press and hold down the tron approximately three seconds. To enable this function again, press and hold down the button approximately three seconds amd with one beep, it returns to proximity door unlock mode, Clock time setup 7-1. Correction of time {£x. to PM 3:20) 3.
3. Press MODE button 10 save your selection and return 10 normal screen. System programming 1 The System programming process works only in disarming status nd within the R¥ transmission range. Depending on the circumstances or your preference, you can select, disable or change various functions and function mode of the System. The programmed value is memorized to the Main Control Module and is not deleted even if you replace the battery in the Remote Control as long as you do not initialize the System. 8.
Ignition ante door locker) On/Off If the vehicle has a factory-equipped speed-sensing door lock system, you should not use the IG dock function of this System. Disable it by setting the program See 6-1, page 2477) 0.Press MODE button for thees seconds and STEP’ indication is displayed two beep sounds. ©. Press MODE button once again, With one beep sound, “Sysop# indication is displayed. 0.Press PRIG button three tines and ‘dr ON indication is displayed. I1.
SYS # indication is displayed. 11. Press PRIG button six times and ‘54 OF" indication is displayed. 1. Pres SET button to select from ON". 1. Press MODE button to save your selection and return to normal screen. 2277027218-7, Proximity door unlock(Ad) On/Off ‘This enables or disables the function of proximity door unlock function. O. Fress MODE button for 3 seconds and ‘STEP’ indication is displayed with two beep sounds, £3. Press MODE button once again, With one beep sound, Sys # indication is displayed.
Technical support Shut-down of battery power to the System 1 an unexpected error occurs or when the alarm activates without definite reasons, remove the fuse a3 in the following steps to block the vehicle's power supply to the System. 13. Open the door with ignition key or with other methods. 13.
J. Press SET button to select ‘En [1.Press MODE button to save your selection and return to normal screen. 9-3, Cold weather start mode(CS) selection After programming the function, beep will be emitted from the Remote Control, to remind you of your setup mode. One beep sounds whenever you press the button . [One beep from the Remote Control when you press the button means that your selection is one hour engine start interval.
ten seconds after the dashboard illuminates. press the program button (Valet button) three times as the first digit of the defile password of the System is 3°. 3. Turn the ignition key to “OFF” position. 4. Tum the ignition key to ‘ON’ position again, 5. Enter the second digit of the default password. press the program button (Valet button) three times as the second digit of the default password of the System is ‘3°. 6. Tum the ignition Key to ‘OFF position. 7.
4. Turn the ignition key to ‘OFF’ position. $. With one longer beep sound, the codes entered in the System will be erased, (D). #3-4 ; Initialization of the System If the System is initialized, all the set value of the System returns to factory setup mode and the memorized code of the Remote Control will be deleted too from the System, 1. Turn the ignition key to “ON position in the Valet mode {after completing above Step 1.) 2.
and ignition key are lost or connected in the middle of you do not know the reason | the RED wire from the Main for the malfunction. Control Module(D) See?? p37) and contact nearby dealer Verify if the fuse is cut, Replace the fuse, which Is connected in the {30A, For vehicle use) All functions of | middle of the RED wire [1 See the System de {coming from the Main Control not work. Module. Verify if the vehicle's battery | Replace the vehicle's battery. is completely discharged.
dome light is at the position | closed or put the dome light where it is interlocked to be | switch at the center position. muted on whenever the , doors are opened. ee woebegone For automatic transmission | Make sure that the vehicles, check the position | transmission gear is at does not work. | of the transmission gear, the position. Verify the connection Connect the wire properly, status of BLACK ground if not, wire coming from the N Main Control Module.
function should be used discreetly. Dio not activate the remote start system in an enclosed ares as it can be very hazardous to your health due to the vehicle exhaust, LIMITED WARRANTY This Vehicle Alarm & Starter product is warranted against manufacturing defects in material and workmanship for{ } days from the date of purchase from the authorized Dealer of [ I During the period, the Dealer will repair the Auto Alarm product without charging the parts and Tabor cost.
Remote control functions 3.1. Door lock & arm the vehicle... 10 3-2. Door unlock & disarm the vehicle . n 3-3. Trunk release 12 3-4. Emergency panic alarm 3-5. Vehicle finding 3-6. Vibration mode .. 3.7. Indoor temperature 3-8. Mute chirp sound 3.9. Button lock 3-10. System's status check 3.11. Personal alarm call 3-12. System valet mode Alarm functions 4-1. Alarm by door open sensing 4-2. Alarm by shock sensing 4-3. Hidden Alarm{Alarm sound Off) 4-4. Engine start disable in arming status 4-5.
9-4, Delay time set-up .. 35 9-5. Set-up of alarm time triggered by shock sensor 36 Technical support ~1. Shut-down of battery power to the System 37 2. System initialization 38 «3. Code memorizing of Remote Control 39 4. Tips for Troubleshooting — 40 Use of one-way Remote Control -1. Door lock/arm the System 42 «2. Door unlock/disarm the System 42 -3. Remote engine start 43 4. Trunk release 43 5. Mute chirp sound 43 6.
«4, Trunk release Press and hold down button for approximately 3 seconds. ~5. Mute chirp sound (one time only) Press button before pressing button or to operate the Systems function, 6. Emergency panic siren Press and hold down button for approximately 3 seconds Delete Delay time{Sh) setup You may need to adjust the delay time for sensor trigger after shutting down th cooling fan runs a different time duration according to vehicle type. You can select £ 90 seconds. (1.