User's Manual

ManualsBrandsTelematics Wireless ManualsElectronicsDual Frequency T-Seal

REV.

∆

DESCRIPTION E.C.N. DATE DRAWN CHECKED

A 086 22/01/05

B According to FCC remarks

C FCC remarks 5/02/2005

PROPRIETARY INFORMATION

ALL RIGHTS RESERVD, NO PARTS OF THIS DOCUMENT MAY BE REPRODUCED, STORD IN

RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC,

MECHANICAL PHOTOCOPYING, RECORDING OR OTHERWISE WITHOUT THE PRIOR WRITTEN

PERMISSION OF TELEMATICS WIRELESS LTD. NOR USED IN WHOLE OR IN PART FOR ANY

PURPOSE OR FOR ANY CUSTOMER EXCEPT TELEMATICS WIRELESS.

DESIGNED G.F.K. 22-Jan-2005 SHEET/OF

CHECKED M.N. 23-Dec-2004

APPROVED A.S. 23-Dec-2004

NAME:

TDMA SEAL-FP200 INT

User Manual

Q.A. A.S. 23-Dec-2004

PROD/PROJ: TSEAL

SIZE

Summary of content (10 pages)

PAGE 1
REV. ∆ DESCRIPTION A B According to FCC remarks C FCC remarks 5/02/2005 E.C.N. DATE 086 22/01/05 DRAWN CHECKED PROPRIETARY INFORMATION ALL RIGHTS RESERVD, NO PARTS OF THIS DOCUMENT MAY BE REPRODUCED, STORD IN RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC, MECHANICAL PHOTOCOPYING, RECORDING OR OTHERWISE WITHOUT THE PRIOR WRITTEN PERMISSION OF TELEMATICS WIRELESS LTD. NOR USED IN WHOLE OR IN PART FOR ANY PURPOSE OR FOR ANY CUSTOMER EXCEPT TELEMATICS WIRELESS.
PAGE 2
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. WARNING! Changes or modifications to this unit not expressly approved by Telematics Wireless Ltd. could void the user's authority to operate the equipment.
PAGE 3
FP200INT User Manual Table Of Contents 1. GENERAL INFORMATION ............................................................................. 4 1.1 1.2 1.3 2. INSTALLATION PROCEDURE ....................................................................... 4 2.1 2.2 2.3 2.4 3. INTRODUCTION........................................................................................................... 4 PURPOSE ......................................................................................................
PAGE 4
FP200INT User Manual 1. General Information 1.1 Introduction The T-SEAL int is a TDMA seal, based on AVI transponder with enhanced functions. The T-Seal int is compatible to currently installed TDMA reader in variety of projects, such as WIM and border crossing. Additionally, Telematics-Wireless provides handheld reader for T-Seal int information access and setting. Note: Everywhere 2.4 GHz is mentioned, the actual real frequency is 2.44 GHz. 1.
PAGE 5
FP200INT User Manual Step 1: Turn on the HH reader Step 2: “Search” for the T-Seal int and verify correct T-Seal int ID Step 3: Go to file and delete old status file for that T-Seal int Step 4: Select the T-Seal int and go to Setting Step 5: Set the T-Seal int time (make sure the HH reader time is set to GMT) Step 6: Set the sensor: Door enabled (√) and C External disabled and O And click Sensors Step 7: Reset the T-Seal int 2140-72017-00-0A REV: C Page 5 Of 10
PAGE 6
FP200INT User Manual Step 8: Verify T-Seal int is ready: Inactive Door sensor enabled and tampered (RED) No sealing and tampering records Step 7: If applicable, Set the Freight Information The T-Seal int in now ready for installation 2140-72017-00-0A REV: C Page 6 Of 10
PAGE 7
FP200INT User Manual 2.2 Attached the T-Seal int and Magnet on Container Doors The 2nd phase is installing the T-Seal int and the sensor’s magnet in the container. Step 1: Attach the T-Seal int’s on the container right door (looking from inside) 5 inches from the door top and as close as possible to the door edge. Step 2: Attach the magnet on the other door 7 inches from the door top and as close as possible to the door edge.
PAGE 8
FP200INT User Manual 2.3 Activate T-Seal int The 3rd phase is activating the T-Seal int. Step 1: “Search” for the T-Seal int using the HH reader, select it and verify that the door sensor is enabled and secure. Step 2: Go to Setting and enter the lock number Step 3: Click Activate.
PAGE 9
FP200INT User Manual 2.
PAGE 10
FP200INT User Manual 3. MONITOR T-SEAL INT STATUS 3.1 Monitor T-Seal int Status Using Handheld Reader See HH reader user manual.pdf 3.2 Monitor T-Seal int Status Using TDMA Reader A standard TDMA reader can get the T-Seal int status by performing read internal memory command. In standard AVI transponder the 4 bytes followed the transponder ID are 0.