DTR4000CA User Manual Satellite Solutions Copyright© 1999 GLOBAL TELEMANN SYSTEMS Inc. All rights reserved. This manual is subject to change without prior notice. GLOBAL TELEMANN SYSTEMS Inc. TEL:+1 408 955 7750 / FAX:+1 408 955 7740 2345 Harris Way, Suite 100, San Jose, CA95131, USA E-mail : info@telemann.com WWW : http://www.telemann.
DTR4000CA Safety Precautions Table of Contents INTRODUCTION ................................................................................................................................................. 6 ABOUT THIS MANUAL.......................................................................................................................................... 6 GENERAL DESCRIPTION.............................................................................................................................
DTR4000CA Safety Precautions
DTR4000CA Safety Precautions RADIO FREQUCNCY INTERFERENCE STATEMENT Note : This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to part 15, Subpart B of the FCC Rules. This equipment generates, Uses, and can radiate radio frequency energy. If not installed and used in accordance with The instructions, it may cause interference to radio communications.
DTR4000CA Safety Precautions SAFETEY PRECAUTIONS This IRD has been manufactured to meet international safety standards. Please read carefully the following safety precautions before you handle the IRD. MAINS SUPPLY LOCATION CLEANING OVERLOADING VENTILATION LIQUIDS SAMILL OBJECTD ATTACHMENTS CONDITIONAL ACCESS (CAM) and/or COMMON INTERFACE MODULE CONNECTION TO THE SATELLITE DISH LNB EARTHING LIGHTNING SERVICING Use only 85-265V AC 50/60Hz.
DTR4000CA Introduction Introduction About This Manual This manual describes how to install and operate the Model DTR4000CA. Only qualified personnel should handle any problems beyond this manual. General Description The DTR4000CA is a high-performance IRD (Integrated Receiver Decoder). DTR4000CA is fully compliant with the MPEG2 based DVB transmission standards for in-home reception of satellite digital broadcast services such as digital TVs and radio channels.
DTR4000CA Hardware Description Hardware description Here, you will be given the explanation of the front and rear panel of DTR4000CA. Each of display, ports, connections will be explained. Front Panel Configuration 1 LED DISPLAY This shows the channel number or other information as follows : During power is off, the dash ‘-‘ will be displayed at each digit, which indicates that your DTR4000CA is in stand-by mode. Immediately after your decoder turns on, ‘C . . .
DTR4000CA Hardware Description of the DTR5000N. When you want to watch Pay-per-view TV program or enjoy Internet service on a usage basis, you should purchase a smart card or PCMCIA card from the service provider and insert it into this slot. The detailed usage explanation will come with the card that you purchased. 5 CHANNEL DOWN You can sequentially select the previous service by pressing this DOWN key. 6 POWER This key allows you to turn your DTR4000CA on or off.
DTR4000CA Hardware Description Rear Panel Configuration The following diagram shows the DTR4000CA with analog board. Here the dotted line can be replaced with the Modem board (option) below. 1 LNB IN Satellite antenna input terminal. The LNB power (14/18V) and the switching signals (22KHz/DiSEqC) are also supplied to LNB through this terminal. 2 LNB OUT It is for connecting another STB to your DTR4000CA. Connect this terminal to LNB IN terminal of the other STB via RF cable.
DTR4000CA Hardware Description This terminal is connected to S-VIDEO input terminal of TV or VCR to output S-VIDEO signal. 7 TV SCART connector Connect this connector to that of TV via a SCART cable. 8 9 Modem Port (Option) When you use Conditional Access System, you should use modem to send your usage information to the operator. VCR SCART connector Connect this connector to that of VCR via a SCART cable. 10 0/12V OUT Connect this terminal to an external 0/12Volt switch box.
DTR4000CA Hardware Description Connection of your DTR4000CA to a TV set Connect your DTR4000CA to a TV set with SCART. Connection of your DTR4000CA to a VCR Connect the SCART connector of VCR to that on your DTR4000CA. Connection of your DTR4000CA to a Hi Fi system Connect a RCA/Cinch stereo cable from the AUDIO L/R terminals on your DTR4000CA to the LINE, AUX, SPARE or EXTRA input terminals on your Hi Fi system.
DTR4000CA Remote Control Remote Control Remote Control Unit This section describes how to operate the DTR4000CA using the buttons on your Remote Control Unit as shown below. (1) POWER (2) TV/SAT (3) Number To turn your DTR4000CA on/off. To toggle from TV mode to satellite broadcasting mode and vice versa To select channel number or input parameters on menu.
DTR4000CA (4) RECALL (5) i (6) MENU (7) EXIT (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) LIST VOL UP/DN OK CH UP/DN Page UP GUIDE Page DOWN AUDIO Language( ? ) MUTE NTSC/PAL FAV F1 F2 F3 Remote Control To return back to the previous channel. To display the program information on the screen To display the main menu on the screen. Or to move back to previous menu from current menu. To get completely out of menu.
DTR4000CA System Set-up System Set-up Here, we will go through the menu system.
DTR4000CA System Set-up Flow of Menu System Here, the following diagram shows the hierarchy of menu system. For detailed explanation of each menu, refer to the following Menu explanation.
DTR4000CA System Set-up AccessGate Edit Channels Group Entitlement Channel Entitlement Remainder Token List Usage-record Amount of Record List of Record Modify Smart Card PIN Change PIN This Menu has several submenus This menu has a final setting menu This menu will be added later Fig 5.
DTR4000CA System Set-up Automatic Channel Set-up Automatic channel set-up for a satellite You can automatically detect and save all TV and Radio channels for a Satellite As follows. System Connection Connect DTR4000CA with all peripheral devices. Power on Turn on the power of DTR4000CA and other devices. Move to the menu of Installation, and then LNB configuration Main Menu/Installation/ LNB Configuration LNB Configuration Setting Insert all LNB information of your Antenna.
DTR4000CA Factory Default Satellite Information Menu Operation Main Menu Main menu shows the following information. Channel Guide Shows general information about each channel such as Channel Name, LNB Number, PID Number. Channel List Shows the whole channel list registered in DTR4000CA Parental Control Allows only those people with knowledge of the PIN code to watch the programs. Installation Allows you to set various parameters on LNB configuration, System Settings, and etc.
DTR4000CA Factory Default Satellite Information Guide. Channel List TV and Radio Channel List This menu helps you easily select the channel that you want to watch. In Main Menu, select Channel List. Then you will see TV Channels display as follows. You can get the information of Channel Number, Channel Name, and whether the program Scrambled or Clear. To watch a specific channel, first select a certain channel by pushing the Up/Down key, Page Up/Down key.
DTR4000CA Factory Default Satellite Information PID number. The PIN code is four digit numbers. Factory default value is 0000. Press UP/DOWN key to highlight the program you want, then press OK to have the channel locked so that others who do not know the PID can not watch the program. Once the program is locked, every time you try to watch the program, you will be asked to enter PIN code. When you push “ ” on the Remote Control, you can select either TV or Radio Guide.
DTR4000CA Factory Default Satellite Information Enter your PIN, then press OK to confirm it. Then submenus will appear, which allows you to change the preferences that were set factory default values. You can also add features to the existing selections. LNB Configuration LNB Configuration helps you enter information of LNB that is connected to DTR4000CA In Installation menu, select LNB Configuration.
DTR4000CA 22KHz Tone Burst DiSEqC Factory Default Satellite Information Depending on the use’s antenna switch box or LNB, you can supply either 22KHz by setting “On” or off by setting “off” Depending on the user’s antenna switch box, you can pick up either A by setting “SA”, B by setting “SB”, or “Off”. If you have DiSEqC box(es), you can choose port one to four by selecting port number one to four.
DTR4000CA Factory Default Satellite Information Edit Channels User can manage Channels stored in DTR4000CA – Delete, Add programs to Favorite Channels. In Installation Menu, select Edit Channel menu. Then the following Edit Channel Menu screen will display. Edit TV Channel You can delete the unnecessary TV Channels from the registry of DTR4000CA. In Edit Channel menu, select Edit TV Channel menu.
DTR4000CA Factory Default Satellite Information From the channel list on the screen, you select the channel that you do not want to watch. Then click “F3” button twice. The channel disappears from the DTR4000CA program list.