MODEL: TTV-299 FULL ON SCREEN DISPLAY 228 PROGRAM MEMORY WITH INFRARED REMOTE CONTROL OWNER'S MANUAL
Dear Customer: Thank you for purchasing our latest TV set. Please read this instruction manual carefully first before operation so that you can use it in a safe and reliable manner. Please also store it safely for future reference. Contents I. Safety and Precautions………………………………………………………………….. II. Installation 2 Antenna connection. ……………………………………………………………………… 3 Remote control Preparation …………………………………………………………….. 4 III.
Safety and Precautions To ensure safe and reliable operation of the TV set, please observe the following precautions in installation, operation and maintenance. 1·Pay attention to the power supply cord before installing the TV set. Do not hang anything on the cord, and avoid treading on the cord. 2·The slots on the back housing are designed for ventilation to prevent overheating. They must Attention: ttention: never be covered or blocked.
Installation First read carefully the relevant instructions in “Safety and precautions”. Place the TV set in the room where there is no direct sunlight on it. Any light reflecting from the screen will cause eye fatigue. Use gentle indirect lighting for comfortable watching. The best distance of watching is 5~7 times the screen height. Keep a space of 10 cm or over between the TV set and wall for good ventilation.
Installation Remote Control Preparation Installing the batteries 1 Remove the sliding cover from the remote control. 2 Load two Size AAA batteries into the chamber, with the +/- poles of batters in line with the +/- marks. Precautions in operating the remote controller ● Aim the remote control at the infrared receiving window on the TV set. ● Do not press the keys on the remote control quickly and continuously.
Control Location Television Front Panel & Input/ Output Terminals The control buttons are in the front of the TV (below the picture tube), behind the cover. 1. Main power switch 2. Remote control sensor 3. Power indicator 4. Program number up (+) and down (-) 5. Volume up (+) and down (-) 6. Menu button 7. TV/AV button 8. AV socket 9.
Names and Functions of Controls Remote control 1 13 2 3 4 14 5 6 16 17 18 7 19 15 20 8 9 21 10 22 11 23 12 24 Buttons on remote controller: 1. AV status switch button 2. TV switchover 3. Sound system button 4. Game button 5. AVL button 6. Clock button 7. Volume UP/DOWN button 8. Prog.swap button 9. Tuning button 10. Feature button 11. Direct Program number buttons 12. Mute button 13. Standby button 14. Screen display button 15. Colour system button 16.
Operating Instructions Turn the power supply ON/OFF 1. Press the power switch, the power indicator will be on, and after several seconds, the tv set will begin normal operation. 2. Press the button on the remote controller, the television will be in standby mode and button on The power indicator will be on but the screen off. In this mode, press the the remote control or the direct program number buttons (0-9).
TV Operation Program Selection 1 Selecting a desired program Use the direct Program number Selection buttons Press the number buttons 0-9 on the remote control to select the single digit program number (0-9). Press the “-/--” button on the remote control to display to select double-digit programs.
TV Operation Start operation: Adjustment 1 Program preset (auto search) When you turn on the TV set for the first time, you must select the “MENU” button continuously on the TV or the remote control, so that the following menu is displayed on the screen: TUNING PROG. 1 AUTO STORE SEARCH FREQ.FINE BAND VHF-L SKIP OFF ┃┃· · · · · · · · · · · · Use “P+/P-” button to select “AUTO STORE” option (it turns from white to green), then press “V+” button to begin the auto search.
TV Operation Start operation: Adjustment TUNING PROG. 1 AUTO STORE SEARCH FREQ.FINE BAND VHF-L SKIP OFF ┃┃· · · · · · · · · · · · You can first use P+/P- or direct program number on remote control to select the program number you want to tune manually. Once the channel is selected press “MENU” button until you enter the “TUNING” menu. Move the cursor to "SEARCH" by pressing the “P+/P-” button (it turns from white to green), and then use “V+/V-” to begin manual tuning.
TV Operation Start operation: Adjustment TUNING PROG. 1 AUTO STORE SEARCH FREQ.
TV Operation Basic operation: Picture and sound control 1 Mute and screen display Mute The Mute function may be used to mute sound. When you need mute, press the “Mute” button on the remote controller, and the screen will display the red characters “MUTE”. If you want to restore the sound, press the “Mute” button again. Note: Automatic mute is ON in program switchover, in blue screen, in TV and AV mode and during searching.
TV Operation Basic operation: Picture and sound control Set your desired picture mode Press “MENU” once or “PICTURE” button to show “Picture” menu on the screen, then press “P+/P-” to select the item you want to adjust. Press “V+/V-” to adjust the effect. PICTURE BRIGHT 55 CONTRAST 75 SATURATION 55 SHARPNESS 75 HUE 0 Note: HUE adjustment is only available in NTSC, its adjusting range being -50~ ~+50, ~100.
TV Operation Basic operation: Setting time With this function, you can watch the preset program or place the TV set in standby mode at set time. For example, if it is 18:28 now, and you want to watch Program 6 at 19: 00, and turn off at 22:30 (standby); and then to turn on again at 7:30 the next morning to show Program 12. The operation is as follows: 1. In TV mode press “MENU” button four times or directly press “TIMING” button, to enter “TIMING” menu.
TV Operation TIMING CLOCK --:-TIMER ON --:-PROGRAM 0 TIMER OFF --:-SLEEP TIMER 0 Basic operation: Setting the sleep Time, screen display language and auto volume limit 1. Setting Sleep Time You can set the Sleep Time directly. In TV mode press “MENU” button four times or directly press “TIME” button, to enter “TIMING” menu. Then press “P+/P-” to select “SLEEP TIMER” (it turns from white to green), and press continuously V+/V-, you can set the off time in the range of 15-120 min. (at steps of 15 min.).
TV Operation white to green), and press “V+/V-” to set AVL to “ON” or “OFF”.
TV Operation Program order arrangement After auto search, there may be some repeated Program Numbers and some blank Program Numbers. To skip over these Program Numbers and arrange the desired Program Numbers, you can do the following: Press the “MENU” button 6 times or press directly “SWAP” button on the remote controller, so that the screen displays the “PROG. SWAP” menu, then press “P+/P-” button to choose “PROG.1” (it turns from white to green). PROG.SWAP PROG.1 PROG.
Connect with Other Devices Connect CD, VCD, DVD or other sound, picture and audio or video output devices Video television, VCD, DVD, game set or other sound and picture output devices RF output To antenna input Video television, CD, satellite receiver or other sound and picture output devices To video input VIDEO OUT AUDIO L-OUT-R Video output To audio input Video output Audio output To video input VIDEO IN 18 AUDIO L-IN-R
Miscellany Guide to simple trouble-shooting The following phenomena are not necessary faults, and the following checks should be performed first before asking a specialized person for repair. If the cause of fault cannot be found and corrected with this guideline, remove the power plug from the socket and have a specialized person to repair it.
Miscellaneous Specification ● Receiving system: RF: PAL B/G AV: NTSC 3.58, NTSC 4.
21