User's Manual

ManualsBrandsTeleEpoch ManualsElectronicsPACE4

 1

InstructionsforSiteInstallationand

Commissioning



Overview



1. Briefing/TeamedTraining/TechnicalAssistance

:TechnicianswhohavenotinstalledPACE+PACECloud

will be briefed on operation and installation, either in person, via Webinar or tele‐training.Training will

includeinstructionsoninstallation,documentation,closeout,andcontactingtechnicalsupport.



2. AboutInstallingthePACE4Suite

:ThePACE4moduleinstallswithinthelowvoltagecontrollines,and

using adaptive software, periodically simulates a thermostat‐satisfied signal to compressor/fan and burner

elementswhilemaintainingtheOEMsequen ceofoperationandblower/fan operationforcooling,toimprove

heat transfer during either cooling or heating. Equipment run time is

 reduced while cooling and heating is

continued, and as with an automobile’s engine, the PACE4 module’s “hypermiling” software enforces

maximum‐cycleandanti‐shortcyclinglimits.Refertothehelpsectionintheon‐screenmenuformoredetails.



3. PACE4CloudConnectivity

:Inadditiontostanda loneofflineoperation,thePACE4modulecanconnect

to the PACE4 Cloud using either WiFi or Cellular (4G LTE) communication. A single‐purpose cellular or WiFi

antenna, or a Cellular + WiFi combo antenna will be provided when communication is opted‐in by the

customer.





Cellular:Inthisconfiguration,thePACE4moduleusestheintegratedcellularradioforcommunication,

withouttheneedforanadditionaldevice.



 WiFi:In thisconfigu ration,  all PACE4modules ata site connect via WiF i,  to a central WiFi to internet

gateway,whichinturnconnectstoPACE4Cloud.



FeaturesaddedwithPACE4Cloudconnectivityincludetheabilityto:

 ParticipateinAutomatedDemandResponseprograms

 BypassandprogramPACE4modules

remotely

 Remotemonitoringof:

o Thermostatsignals

o PACE4state

o Supply,returnandothertemperaturesdependentonthermistorsinstalled

Summary of content (5 pages)

PAGE 1
Instructions for Site Installation and Commissioning Overview 1. Briefing/Teamed Training/Technical Assistance: Technicians who have not installed PACE+PACE Cloud will be briefed on operation and installation, either in person, via Webinar or tele‐training. Training will include instructions on installation, documentation, closeout, and contacting technical support. 2.
PAGE 2
o Energy consumption and savings (The connection method must be configured using the on‐screen options on the device. Refer to the document “Project Specific Guidelines” to determine means of communication) 4. Components:The following components are included in typical PACE4 installations. Their purpose and other details shall be covered during training. Summary of Steps 1.
PAGE 3
2. Mounting the hard dware: Thee PACE4 mo odule can be b mounted d inside thee control caabinet of th he HVAC unitt, using the provided back b plate. Screw the back‐plate at an appro opriate spot inside the e cabinet. Slide S the PAC CE4 modulee into the to op lip of th he back platte, and snap the botto om into thee 2 clips at the bottom m of the back plate. Figure 1. Mountiing the PAC CE44 3.
PAGE 4
LTE Antenna A Port WIFI Antenna Port Figuree 2. An ntenna mounted on an HVAC unit 5. m arre equipped d with an LCD L touchscreen to alllow configuration. PACE4 Configuratiion:PACE4 modules On nce powered‐up, configure the PA ACE4 node using the on‐screen instructions i s. Configuraation steps include enttering the HVAC H unit tyype, locatio on serviced, nameplatee data, and other o param meters to tw weak the alggorithm beh havior. Site Acccess/Site Closeout: Pleease follow 6.
PAGE 5
FCC Statement § 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. § 15.