User's Manual

Code Number:
TVTXI916S01-2-3-4-6-7
Series
TVLink RS916
Model number
Date
13/01/14
TRANSMITTER, ARTICLE
ART. TVTXI916S01-02-03-04-06-07
(with ‘B’: white colour, with ‘N’:
black colour).
DESCRIPTION OF THE PRODUCT
UHF band transmitter with PPL controlled carrier
frequency. This type of transmitter is used for
controlling devices for domestic use, automatic
openings, ON-OFF light control, dimming, etc.
This appliance transmits a rolling code type signal
to prevent duplication and guarantee maximum
secrecy. The transmitter code can be stored in
the receiver directly via the latter or via radio from
the transmitter. With the second possibility you
can add new transmitters to an existing system
without having to touch the receiver. This can be
done directly by the end user (the installer’s help is
not required). The code is stored in the receiver’s
EEPROM memory that retains it even if power is
cut temporarily.
SAFETY RULES
• Do not use the manual transmitter in places or
where systems are sensitive to radio emissions
(e.g. airports, hospitals).
• Do not keep or use the manual transmitter in
places that are damp, where there is steam, high
air humidity, dust or where it is exposed to the
direct rays of the sun or similar environmental
conditions.
• Do not let the manual transmitter drop: it could
be damaged or its range of action reduced.
Changes or modication not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
USE
• The operator is in no way protected against
interference from other telecommunication
equipment or systems (e.g. authorised radio
systems working on the same frequency range).
• If you are having problems with its range of
action, x the manual transmitter up high. Change
the battery if necessary.
• Do not use your nails to press the key as they
could damage the keys.
CHANGING THE BATTERY
• Keep the batteries out of the reach of children.
Call a doctor immediately if a battery is swallowed.
• Explosion hazard if the battery is substituted
incorrectly.
• Replace the battery with a CR 2430 type battery
only.
• Always wrap the battery up, both when it is being
stored and when it is being disposed of. The
battery should not come into contact with other
metal objects as it could cause the battery to run
down, catch re or be damaged.
• Dispose of damaged or nished
batteries immediately in compliance
with the law. To this end, contact
the authorities for safeguarding
the environment or the centre for
disposing of waste materials in your
area.
• Do not throw the battery away with household
rubbish.
1.Open the cover.
2.Take the old battery out and put the new one
in in the same way.
Pay attention to correct polarity (+/-)!
WALL FIXING
If the transmitter is xed on the wall with
biadhesive, the maximum holding
will be reached after 24 hours from the application.
Application temperature min.+10°C.
GUARANTEE
The guarantee complies with the law. If the
guarantee has to be used please refer to the
specialized retailer. The right to the guarantee is
applicable only for the country in which the manual
transmitter was purchased. The batteries are not
covered by the guarantee.
HOW TO STORE A TRANSMITTER VIA RADIO
WITHOUT ACCESSING THE RECEIVER
BY MEANS OF A PREVIOUSLY STORED
TRANSMITTER
- Press the internal key P3 of a previously
stored transmitter , the enabled receiver emits a
continuous sound for 5 seconds.
- Transmit a channel present in the memory
of the receiver, in which the new codeis to be
memorized, within 5 seconds and the buzzer will
interrupt the sound for 1 sec, and then carry on for
another 5 seconds.
- Transmit the new channel to store within 5
seconds, conrmed by intermittent buzzing.
DECLARATION OF CONFORMITY
Teleco Automation SRL declares that the above
mentioned articles satisfy the following technical
regulations applicable:
- FCC (Federal Communications Commission
Part 15 (FCC ID: P59TVTXI916S)
- IC (Industry Canada) RSS-102
(IC: 11242A-TVTXI916S)
TECHNICAL DATA
The transmitters are coded directly by the
manufacturer with a different code for each
transmitter.
Technical specications
Carrier frequency 916 MHz-
Modulation FSK
Power supply 3V ± 10%
(lithium battery CR2430)
Consumption when
transmitting 10 mA
- Working temperature - 10° to +55°C
In the view of a constant development of their
products, the manufacturer reserves the right
for changing technical data and features without
prior notice.
EN
Only single
memorization
single or in pairs
memorization
This document is the property of teleco Automation Srl who reserves all reproduction
and copying rights
The memorisation of the “single” or “in pairs” channels depends on the
functions of the receiver.
TELECO AUTOMATION SRL - Via dell’Artigianato, 16 -31014 Colle Umberto (TV) ITALY
PHONE: [phone] FAX:[phone]
CH1
CH1
CH2
CH5
CH6
CH7
CH1
CH2
CH3
CH4
LED
LED
LED
LED
single or in pairs
memorization
(CH1 with CH2
and CH3 with
CH4)
CH5
CH6
CH7
CH5
CH6
CH7
LED
LED
CH5
CH6
CH7
CH1
CH2
CH3
CH4
Attention:
The 6-pushbutton transmitter works as two
separate 3-pushbutton transmitters. These
two 3-puhsbutton transmitters have the
memorization push-button P3 in common.
Before using the pushbutton P3, press one
of the channels to be associated with.
single or in pairs
memorization
(CH1 with CH2)
single or in pairs
memorization
(CH6 with CH7 or
CH5 with CH6 and
CH7)
single or in pairs
memorization
(CH6 with CH7
or CH5 with
CH6 and CH7)
single or in pairs
memorization
(CH6 with CH7
or CH5 with CH6
and CH7)
TVTXI916S01B
TVTXI916S01N
TVTXI916S02B
TVTXI916S02N
TVTXI916S03B
TVTXI916S03N
TVTXI916S04B
TVTXI916S04N
TVTXI916S07B
TVTXI916S07N
TVTXI916S06B
TVTXI916S06N
single or in pairs
memorization
(CH1 with CH2 and
CH3 with CH4)
single or in pairs
memorization
(CH6 with CH7 or
CH5 with CH6 and
CH7)
P3
T604.01_EN
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.