User's Manual

Code Number:
TVEVO916S03/04/07/18/42
Series
TVLink RS916
Model number
Date
13/01/14
TELECO AUTOMATION SRL - Via dell’Artigianato, 16 - 31014 Colle Umberto (TV) ITALY
TELEPHONE: ++39.0438.388511 FAX: ++39.0438.388536
DESCRIPTION OF THE PRODUCT
UHF band transmitter with PPL controlled
carrier frequency. This type of transmitter is
used for controlling devices for domestic use,
automatic openings, ON-OFF light control,
dimming, etc. This appliance transmits
a rolling code type signal to guarantee
maximum secrecy. The transmitter code
can be stored in the receiver directly via
the latter or via radio from the transmitter.
With the second possibility you can add new
transmitters to an existing system without
having to touch the receiver. This can be done
directly by the end user (the installer’s help
is not required). The code is stored in the
receiver’s EEPROM memory that retains it
even if power is cut temporarily.
SAFETY RULES
• Keep this manual transmitter out of the reach
of children and animals.
• Do not use the manual transmitter in places
or where systems are sensitive to radio
emissions (e.g. airports, hospitals).
• Do not keep or use the manual transmitter
in places that are damp, where there is
steam, high air humidity, dust or where it is
exposed to the direct rays of the sun or similar
environmental conditions.
• Do not let the manual transmitter drop:
it could be damaged or its range of action
reduced.
Changes or modication not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
USE
• The operator is in no way protected against
interference from other telecommunication
equipment or systems (e.g. authorised radio
systems working on the same frequency
range).
• If you are having problems with its range
of action, x the manual transmitter up high.
Change the battery if necessary.
CHANGING THE BATTERY
• Keep the battery out of the reach of children.
Call a doctor immediately if a battery is
swallowed.
• Explosion hazard if the battery is substituted
incorrectly.
• Replace the battery with a CR 2430 type
battery only.
• Always wrap the battery up, both when it is
being stored and when it is being disposed of.
The battery should not come into
contact with other metal objects as it
could cause the battery to run down,
catch re or be damaged.
• Dispose of damaged or nished
batteries immediately in compliance with the
law. To this end, contact the authorities for
safeguarding the environment or the centre for
disposing of waste materials in your area.
• Do not throw the battery away with
household rubbish.
1.Open the posterior cover.
2.Take the old battery out and put the new
one in in the same way.
Pay attention to correct polarity (+/-)!
GUARANTEE
The guarantee complies with the law. If the
guarantee has to be used please refer to the
specialized retailer. The right to the guarantee
is applicable only for the country in which the
manual transmitter was purchased.
The batteries are not covered by the guarantee.
DECLARATION OF CONFORMITY
Teleco Automation SRL declares that the
above mentioned articles satisfy the following
technical regulations applicable:
- FCC (Federal Communications Commission
Part 15 (FCC ID: P59TVEVO916S)
- IC (Industry Canada) RSS-102
(IC: 11242A-TVEVO916S)
TECHNICAL DATA
The transmitters are coded directly by the
manufacturer with a different code for each
transmitter.
Technical specications
Carrier frequency 916 MHz
Power supply 3V ± 10%
(lithium battery CR2430)
Consumption when
transmitting 10 mA-
- Working temperature - 10°
– +55°C
In the view of a constant development of their
products, the manufacturer reserves the right
for changing technical data and features
without prior notice.
EN
Only for 42 version
TVEVO916S07/42 Single push button
commands function (ON/OFF or impulsive
TVEVO916S07/42
Commands function on dimmer
Luminosity 100%
Luminosity 75%
Luminosity 50%
Luminosity 25%
Increases luminosity
Decreases luminosity
Off
Open-Stop
Close-Stop
Open-Stop
Close-Stop
Open
Stop
Close
SEL
The selection remains memorised
until the next variation, as well with
turned-off transmitter; it is sufcient
to press a channel push button to
reactivate the last selection.
Each LED-position
represents a
transmitter, (total:
6 positions)
Press the push
button SEL from 1
to 6 times in order
to select the desired
position.
Push-button SEL multi-transmitter function
(only for 18-42 version)
Only for 18 version
Open
Stop
Close
TVEVO916S03/18 - Command function
single or in pairs
memorization
single or in pairs
memorization
only single mem
single or in pairs
memorization
TVEVO916S07/42
Separate push button Open-Stop-Close
commands function
CH5
CH6
CH7
Changing the battery
1 - Remove the screw on the back.
2 - Slide each other the two cases until the opening of the lateral sealing cases.
3 - Raise the cover.
P3 (in all the
versions)
C
R
2
4
3
0
Screw
CH1
CH2
CH3
CH4
CH5
CH6
CH7
SEL
SEL
Only for 42 version
SEL
SEL
Attention.
The functions of SEL push buttons, of group or
sub-group of 18 and 42 transmitters, are set in the
same way.
TVEVO916S04 - Command function
CH1
CH2
CH3
CH4
1
2
3
4
5
6
Only for 42 version
MANUAL MULTI-
TRANSMITTER
ART. m03/04/07/18/42
single or in pairs
memorization
(CH6 with CH7 or CH5
with CH6 and CH7)
single or in pairs
memorization
(CH1 with CH2 and CH3
with CH4)
T603.01_EN
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.