Tele Radio Panther SAFETY INSTRUCTION LANGUAGE: ENGLISH (ORIGINAL) ARTICLE NO: RECEIVER R00008-07 TRANSMITTER T00007-14 IM-PN-CE001-A04-EN
THANK YOU FOR PURCHASING A TELE RADIO PRODUCT READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE MOUNTING, INSTALLING AND CONFIGURING THE PRODUCTS. These instructions are published by Tele Radio AB without any guarantee. The instructions may be removed or revised by Tele Radio AB at any time and without further notice. Corrections and additions will be added to the latest version of the instruction.
WARNINGS & RESTRICTIONS INSTALLING, CONNECTING AND MOUNTING l Allow only licensed or qualified personnel to install the product. l Switch the power supply off to the receiver before connecting the equipment. l Check that you have connected the power supply to the correct connection terminal. l To utilize the safety of the system, use the stop relays in the safety circuitry of the object that you want to control. l Use undamaged cables. No cables should hang loose.
Install, operate and make settings INSTALL, OPERATE AND MAKE SETTINGS IMPORTANT! The transmitter must be registered in the receiver before it is possible to start a radio session. For safety reasons only qualified personnel should be able to install, register and make settings to the Panther system. Installation instructions as well as end user instructions are available for download at: www.tele-radio.com Please, contact your representative for further assistance.
Receiver R00008-07 RECEIVER R00008-07 WARNING! The receiver must NOT be opened by any other than a qualified installer. Make sure to turn the electricity off before opening the receiver. IMPORTANT! Tele Radio remote controls are often built into wider applications. We recommend that the system is provided with a wired emergency stop where necessary. Base board: 1. Relay LEDs (red) 6. Function button (Cancel) 2. Function relays 1-9 7. Programming connector 3. Terminal block for input power 8.
Receiver R00008-07 Expansion board: 10. Relay LEDs (red) 14. Function button (Cancel) 11.LEDs representing the function relays on 15.Programming connector the base board 12. Function relays 10-19 16. Power LED (yellow) 13. Select button (OK) 17.
Receiver R00008-07 TERMINAL BLOCK FOR INPUT POWER TERMINAL BLOCK FOR DIGITAL INPUTS Base board: 33. GND 38.Digital input 5 34. Digital input 1 39.Digital input 6 35. Digital input 2 40.Digital input 7 36. Digital input 3 41.Digital input 8 37. Digital input 4 42.
Receiver R00008-07 TERMINAL BLOCK FOR DIGITAL INPUTS Expansion board: 81. GND 87. Digital input 11 82.GND 88. Digital input 12 83. GND 89. Digital input 13 84. GND 90. Digital input 14 85.Digital input 9 91. Digital input 15 86. Digital input 10 92. Digital input 16 CURRENT CONSUMPTION Input power Min.* Max.** 12V AC 0.02A 0.6A 24V AC 0.02A 0.3A 48V AC 0.008A 0.2A 115V AC 0.004A 0.07A 230V AC 0.003A 0.04A 12V DC 0.03A 0.5A 24V DC 0.02A 0.
Receiver R00008-07 LEDS ON THE EXPANSION BOARD REPRESENTING THE FUNCTION RELAYS ON THE BASE BOARD LED 1= function relay 1 LED 2= function relay 2 LED 3= function relay 3 LED 4= function relay 4 LED 5= function relay 5 LED 6= function relay 6 LED 7= function relay 7 LED 8= function relay 8 LED 9= function relay 9 -9-
Receiver R00008-07 TECHNICAL DATA Number of function relays 19 (potential free*, 8A) Digital inputs 8 Duplex/ simplex communication Simplex Operating frequency 2405-2480 MHz. Number of channels 16 (channel 11-26) IP class 66 Size 176 x 126 x 75 mm./ 6.9 x 5 x 2.9 in. Weight 800 g./ 1.8 lbs. Antenna 1 external BNC antenna Rated voltage 12-24 VDC. Max. 1A 12-24/48-230 VAC, 50-60 Hz. Max.
Transmitter T00007-14 TRANSMITTER T00007-14 1. LED 1 (red) 3. LED 2 (red) 2 Top LED (green/red) 4.
Transmitter T00007-14 TECHNICAL DATA No. of buttons 8 x 1-step buttons On/off switch Yes Size 83 x 52 x 31 mm./3.3 x 2 x 1.2 in. (incl. clip) Weight 70 g./ 0.15 lbs. (incl. batteries) No. of channels 16 (channel 11-26) Operating frequency 2405-2480 MHz. Battery type 2 x 1.5V AAA alkaline ON/OFF SWITCH The transmitter has an on/off switch on the backside. The on/off switch has 2 positions: 1= on 0= off The on/off switch breaks the power supply from the battery.
Transmitter T00007-14 START THE TRANSMITTER 1. Press button 7 (the ON button) for at least 1 second. 2. Release button 7 (the ON button) when the top LED turns green. 3. The transmitter is started. TURN THE TRANSMITTER OFF 1. Press button 8 (the OFF button). 2. The transmitter sends a stop command for 1 second. 3. The transmitter turns off. REGISTER THE TRANSMITTER IN THE RECEIVER 1. 2. 3. 4. 5. Press the function button on the receiver (LED 1 lights red).
Transmitter T00007-14 RELAY FUNCTIONALITY Button 1 activates relay 1, 8, 15 Button 2 activates relay 2, 9, 16 Button 3 activates relay 3, 10, 17 Button 4 activates relay 4, 11, 18 Button 5 activates relay 5, 12, 19 Button 6 activates relay 6, 13 Button 7 activates relay 7, 14 Button 8 is the OFF button CHANGE THE BATTERIES WARNING! Do not recharge the batteries. Attempts to recharge may cause rupture or the leaking of hazardous liquids, which will corrode the equipment. 1.
FCC/ IC label FCC/ IC LABEL FCC STATEMENT Statement for warning: Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s) and Part 15 of the FCC Rules.
FCC statement Cet appareil est conforme aux limites d’exposition au rayonnement RF stipulées par la FCC et l’IC pour une utilisation dans un environnement non contrôlé. L'utilisateur final doit suivre les instructions de fonctionnement spécifiques pour le respect d'exposition aux RF. Lesémetteurs ne doivent pas être placées près d’autres antennes ou émetteurs ou fonctionner avec ceux-ci.
Battery precautions BATTERY PRECAUTIONS Observe the following general battery warnings: n As batteries contains flammable substances such as lithium or other organic solvents, they may cause heating, rupture or ignition. n Risk of explosion if battery is replaced with a battery of an incorrect type. n Do not short circuit, disassemble, deform or heat batteries. n Never try to charge a visibly damaged or frozen battery. n Keep batteries out of reach of small children.
Guarantee and maintenance GUARANTEE AND MAINTENANCE The Tele Radio products are covered by a guarantee/warranty against material, construction and manufacturing faults. During the guarantee/warranty period, Tele Radio may replace the product or faulty parts. Work under guarantee/warranty must be carried out by Tele Radio or by an authorized service center specified by Tele Radio.