Tele Radio SAFETY INSTRUCTIONS LANGUAGE: ENGLISH (ORIGINAL) ARTICLE CODE: R00004-03, R00004-08, T00012-07, T00012-52 FCC-IM-TG-RX005-B03-EN
Thank you for purchasing a Tele Radio product R00004-03, R00004-08, T00012-07, T00012-52 READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND CONFIGURATING THE PRODUCT. These instructions are published by Tele Radio AB without any guarantee. These instructions are solely directed towards qualified installers. The information shall not be handed to end users. The instructions may be removed or revised by Tele radio AB at any time and without any further notice.
RECEIVER TECHNICAL DATA Maximum current consumption RX MODEL 12 V DC 24V DC 48V AC 230V AC R00004-03 280 mA 140 mA 140 mA 20 mA R00004-08 500 mA 240 mA 230 mA 50mA RELAYS: R00004-03 R00004-08 OPERATING FREQUENCY: FREQUENCY BANKS: SIZE: WEIGHT: ENCAPSULATION IP CLASS: 2 safe relays (makes/breaks 16A ACI) + 7 function relays (potential free*,makes/breaks 8A ACI).
RECEIVER TG-R00004-03, TG-R00004-08 BASE BOARD 17 16 15 14 13 12 11 10 9 8 7 6 1 2 3 4 5 1. Stop relays 1+2 LED (red) 2. Stop relays 1+2 3. Obligatory fuse: 2A (slow), must comply with IEC691/EN60691 4. Terminal block for power supply (see next page) 5. Function relays 1-7 6. Relay LEDs1-7 (red) 7. Function LED 7 (green) 8. Function LED 6 (yellow) 9. Function LED 5 (red) 10. Antenna connector 11.Function LED 4 (orange) 12. Function LED 3 (green) 13. Function LED 2 (yellow) 14. Function LED 1 (red) 15.
TG-R00004-08 10 RELAYS EXPANSION BOARD 25 24 18 19 23 22 20 21 18. Terminal block for digital inputs 19. Relay LEDs 10-19 20. Function relays 10-19 21. Relay LEDs 1-9 (see next page) 22. Select button (OK) 23. Function button (Cancel) 24. Base board communicationLED (yellow) 25. Programming connector 18. Terminal block for digital inputs 81. GND 82. GND 83. GND 84. GND 85. Digital input 3 86. Digital input 4 87. Digital input 5 88. Digital input 6 89. Digital input 7 90. Digital input 8 91.
21. Relay LEDs 1-9 LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 LED 8 LED 9 LED 1= function relay 1 LED 2= function relay 2 LED 3= function relay 3 LED 4= function relay 4 LED 5= function relay 5 LED 6= function relay 6 LED 7= function relay 7 LED 8= not used LED 9= stop relay 1+2 LEDs 1-9 on the expansion board indicate the status of the relays on the base board. When one or more of these LEDs are lit, the corresponding relay on the base board is activated (see list).
4. Input power 1. 48-230V AC 2. 48-230V AC 3. (not used) 4. 12-24V AC/DC 5. GND 6. 12-24V AC/DC For DC voltages: Connect positive voltage to 4 or 6. Connect negative voltage to 5. 15. Terminal block for mixed I/Os 32 33 34 35 36 37 38 39 40 41 42 43 32. +12V DC 33. +5V DC 34. GND 35. GND 36. Digital input 1 37. Buzzer 38. Digital input 2 39. GND 40. +3.3V DC 41. RS485A 42. RS485B 43.
TRANSMITTER JOYSTICK T00012-07, T00012-52 6 7 8 DISPLAY 1 1. 2. 3. 4. 8 Left joystick Front switch Function switch Right joystick 2 3 4 5. 6. 7. 8.
LEFT SIDE 1. 2. Side button 1 Side button 2 (safe button) RIGHT SIDE 3. 4. 5.
START UP IN OPERATING MODE 1. Pull out the STOP button. 2. The green/red LEDs 1+2 light up: in green when the battery capacity is good, in red when the battery needs to be charged. See how to charge the battery in “Battery-how to charge”. Select a receiver for the current session by using the left joystick. 3. Press the side buttons 3+4 until the buzzer sounds and LED 1+2 starts to flash. TURN OFF 1. Press the STOP button. The joystick is now turned off.
TRANSMITTER CONFIGURATION MENU MAP SETTINGS> >Channel/Bank >Register >Logout >Erase >Replace >Show receivers >Auto shutdown >Load selection >Startup protection >Settings protection >Learn RFID >Show RFID >Erase RFID >Enter PIN >Show PIN >Erase PIN >Show SW vers.
NAVIGATE IN THE CONFIGURATION MENU • TO MOVE UP AND DOWN: Move the left joystick up and down. • TO SELECT: Press button 4. • TO GO BACK: Move the left joystick to the left. • TO EXIT: Press button 3 or pull out the STOP button. The transmitter will turn off. SWITCH FREQUENCY BANK 1. Pull out the STOP button. LEDs 1+2 light. 2. Press button 3. Keep pressed. 3. Press the STOP button. 4. Release button 3. The configuration menu opens. 5.
7. Put the receiver in registering mode: a. Press the receiver Function button. b. Press the receiver Select button. c. All the receiver relay LEDs light red when the receiver is in registering mode. Wait until the joystick display shows ”Confirm on RX”, which may take up to 15 seconds. 8. Confirm by pressing the receiver Select button. All receiver relay LEDs flash in red 3 times. 9. The joystick turns itself off.
CHARGE THE BATTERY CHARGING UNIT LED BATTERY TYPE: External and rechargeable CHARGE: In a charger unit. 5V DC ±10% (1A) CHARGING TEMPERATURE: 0°C to 45°C/ 32°F to 113° OPERATING TIME: Approx. 15 h. with continuous usage Approx. 27 h. when the display is off SIZE: 256 x 217 x 85 mm. 10 x 8.5 x 3.3 in. • Before using the joystick for the first time, make sure that the battery is fully charged.
FCC AND IC INFORMATION Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s) and Part 15 of the FCC Rules.
TRANSMITTER PRODUCT LABEL PLACEMENT 2 TIGER 1. 2. 16 TIGER 1 Remove the battery from the bottom of the joystick. The product label with FCC/ IC information is placed under the battery.
RECEIVER PRODUCT LABEL PLACEMENT 17
FCC/ IC LABEL PLACEMENT ON TRANSMITTER The FCC/ IC label is placed on the radio module. The radio module is mounted inside the transmitter. L’étiquette FCC/IC est placée sur le module radio. Le module radio est monté à l’intérieur du récepteur.
FCC/ IC LABEL PLACEMENT ON RECEIVER The FCC/ IC label is placed on the radio module. The radio module is mounted inside the receiver. L’étiquette FCC/IC est placée sur le module radio. Le module radio est monté à l’intérieur de l’émetteur.
THE RADIO MODULE FUNCTION Each receiver and transmitter unit in the Tele Radio Tiger product range, contains a radio module that is specifically designed to match a Tele Radio Tiger unit in terms of physical dimensions, connection points, voltage levels, signal interface etc. To use the radio modules in non Tele Radio products is not permitted. The radio modules are designed to interface directly to the main board of the receiver/transmitter unit.
INSTALLATION INSTALLATION INSTRUCTIONS FOR TR236: 1. Make sure that the transmitter unit is turned off. 2. Open the T0012-* enclosure. 3. Connect the antenna cable from the main board to the 1x15 pole pin connector on TR236. 4. Assemble TR236 in the bottom part of the enclosure. Assemble TR236 so that the pin connector faces outwards. INSTALLATION INSTRUCTIONS FOR TR254: 1. Make sure that the unit is turned off. 2. Open the R0004-* enclosure. 3.