KONA ENTERPRISE GATEWAY USER GUIDE Document Type: User Guide Document Number: T0007323_UG Document Issue: 1.4 Document Status: Released Product Name: Kona Enterprise Gateway Product Code: See Table 1 Issue Date: July 14, 2021 © 2020 TEKTELIC Communications Inc., all rights reserved. All products, names, and services are trademarks and registered trademarks of their respective companies. TEKTELIC Communications Inc.
Document Revision Revision Issue Date Status Editor Comments 0.1 1.0 1.1 1.2 1.3 1.4 Nov 19, 2020 March 23, 2021 April 14, 2021 April 19, 2021 May 20, 2021 July 14, 2021 Draft Draft Draft Draft Released Released H. Agus CA H. Agus SM ZH H. Agus First release 2nd Revision 3rd Revision Updated power specification Updated T-Codes/Order Codes Professional Installation Remark Kona Enterprise Gateway TEKTELIC Communications Inc. T0007323_UG Version 1.
Table of Contents List of Tables ................................................................................................................................... 4 1 2 Product Description ................................................................................................................. 5 1.1 Overview .......................................................................................................................... 5 1.2 Physical Interfaces ......................................
List of Tables Table 1: Kona Enterprise Gateway Models..................................................................................... 5 Table 2: Kona Enterprise Gateway Interface Connector Types ...................................................... 6 Table 3: Kona Enterprise Gateway Specifications .......................................................................... 8 Kona Enterprise Gateway TEKTELIC Communications Inc. T0007323_UG Version 1.
1 Product Description 1.1 Overview The Kona Enterprise Gateway module, shown in Figure 1, is a low-power micro-cell gateway with wide-area coverage (up to 500 km2). The module consists of 1 Semtech SX1301 base-band processor multiplexed through an FPGA to provide 8 simultaneous narrowband channels. The design offers both downlink and uplink operations in time-duplex mode.
Figure 2: Kona Enterprise Gateway 1.2 Physical Interfaces Figure 3 illustrates the bulkhead layout for the Kona Enterprise Gateway. Optional LTE Antenna connection Optional LoRa Antenna connection Ethernet/-48Vdc PoE – RJ45 Covered Panel: Serial Debug – USB Dual SIM/ microSD Card - Hybrid Slot Protective Earth Ground Figure 3: Kona Gateway Bulkhead Layout The Kona Enterprise Gateway connectors are listed in Table 2.
Interface Copper Ethernet Earth Ground Connector Type RJ45 Modular Jack Compression lug Kona Enterprise Gateway TEKTELIC Communications Inc. Mating Connector RJ45 modular plug followed by CAT 5e cable Industry standard single-hole lug, M4 (#8) T0007323_UG Version 1.
1.3 Specifications The Kona Enterprise Gateway specifications are listed in Table 3. Table 3: Kona Enterprise Gateway Specifications Attribute Specification Dimensions 208x146x80 mm Weight 1160 g Operating Temperature -40 °C to 60 °C Relative Humidity 10% to 100 % Condensing Operating Altitude -60 m to 4,000 m (-197 ft to 13,123 ft) Power Input IEEE 802.3af, Mode A or Mode B or 4-pair Mode 48 VDC nominal, 37 to 57 VDC operating range 0.
2 Installation 2.1 Overview • The Kona Enterprise Gateway has no internal field serviceable parts. The Gateway module must only be opened by an approved TEKTELIC service center. • All installation practices must be in accordance with the local and national electrical codes. • Do not work on the system during periods of lightning activity. • The Kona Enterprise Gateway is considered permanently connected equipment.
2.2 Unpacking and Inspection The following should be considered during the unpacking of a new Kona Enterprise Gateway. 1. Inspect the shipping carton and report any significant damage to TEKTELIC. 2. Unpacking should be conducted in a clean and dry location when possible. 3. Do not discard the shipping box or foam inserts as they will be required if a unit is returned for repair or re-configuration. 2.
2.4 Required Equipment for Installation The Kona Enterprise Gateway is intended to be installed in controlled area like tower or roof top building with restricted access to general public. The installation and maintenance must be performed by professional trained RF technician. The following tools are required to install the Kona Enterprise Gateway module: 1. A 6 point metric socket set and torque wrench drive. 2. Anti-oxidant compound (NO-OX-ID, Penetrox, Noalox, Ox-Gard or equivalent). 3.
Figure 5: Kona Enterprise Gateway Wall Mounting Screw Locations When mounted, the Gateway module must be oriented with the connector bulkhead pointed down towards earth as shown in Figure 6. Figure 6: Kona Enterprise Gateway Module Wall Mounting Orientation Kona Enterprise Gateway TEKTELIC Communications Inc. T0007323_UG Version 1.
Figure 7: Kona Enterprise Gateway Module Pole Mounting Accessories Figure 8: Kona Enterprise Gateway Module Pole Mounting Orientation Kona Enterprise Gateway TEKTELIC Communications Inc. T0007323_UG Version 1.
2.6 Ground Cable Installation The Kona Enterprise Gateway is considered Permanently Connected Equipment and requires a permanently connected Protective Earth Ground (PEG) conductor. The Protective Earth Ground connection is made through a M4/#8 on center hole lug with 10mm maximum OD to the ground termination point illustrated in Figure 9. The recommended ground cable gauge is #10 AWG. The Kona Enterprise Gateway grounding system shall follow local and national electrical codes.
2.7 RF Cable Installation The Kona Enterprise Gateway installation allows connection to an external LoRa RF antenna and an external Cellular RF antenna. The RF cables attach to an N-Type connector located on the bulkhead of the Gateway. Torque the cable RF connector to 0.79 to 1.13 Nm (7 to 10 in·lbs). The N-Type connector interface to a cable is not water proof and must be taped. TEKTELIC recommends taping with Scotch Wireless Weatherproofing Kit, WK-101.
Radio Compliance Statements Federal Communications Commission This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter 22504-T0007323 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Pendant le fonctionnement du produit, maintenez toujours une distance de séparation d'au moins 0,40 m de toute(s) antenne(s) connectée(s). Avant de réparer le produit, les antennes ou les câbles, éteignez la fonction de transmission ou l'alimentation de l'unité si vous devez vous rapprocher de la distance de séparation minimale. Ce produit doit être installé par des techniciens RF professionnels formés. Kona Enterprise Gateway TEKTELIC Communications Inc. T0007323_UG Version 1.
