Bluetooth Headset with OLED Display ET3000 User Guide
USER GUIDE Contents Overview ..........................................................................................................................................................2 Getting Started..................................................................................................................................................2 Unpacking ezTalker digital ..........................................................................................................................
Overview ezTalker™ digital by Tekkeon is a Bluetooth® headset with a unique OLED digital display that lets you cut loose from your Bluetooth mobile phone. With advanced features like stored number redial, last number redial and voice dialing, you can use the headset to make and receive calls without every touching your mobile phone. You can even access and dial from your mobile phone book for some mobile phones.
Getting to Know ezTalker digital VOLUME UP Button Increases the speaker volume, mutes/unmutes the microphone, and enables scrolling through stored numbers TALK Button Used to turn headset on/off, pair, and make/receive calls VOLUME DOWN Button Decreases the speaker volume, initiates last number redial and call waiting, and enables scrolling through phone book Charging LED Indicates when headset is being charged Earhook Houses battery, and can be positioned to be worn on either ear Blue LED Provides vi
Setting Up ezTalker digital Before using ezTalker digital, you must: • Charge ezTalker digital • Pair ezTalker digital to your mobile phone • Adjust ezTalker digital to your ear preference Directions for each of these activities are provided in the following three sections. Once these steps are completed, you will be ready to use ezTalker digital! Charging ezTalker digital Before using ezTalker digital, you must charge the headset for a minimum of two hours.
Pairing ezTalker digital to Your Mobile Phone Pairing is the process of linking the headset with your Bluetooth mobile phone or other Bluetooth device that supports a headset and/or handsfree profile. Before using ezTalker digital with your mobile phone you must pair the devices. After this process is complete, you can use the headset with your paired mobile phone. You can pair ezTalker digital with up to seven Bluetooth devices.
To Cancel Pairing Mode While you are in pairing mode, you can cancel the pairing process and turn off the headset. 1. While in pairing mode, press and hold the TALK button approximately three seconds until “Off” appears on the display and the headset turns off. Wearing ezTalker digital ezTalker digital is designed to fit comfortably in your ear. The earhook can be positioned to be worn on the right or left ear. The battery is housed in the earhook, so the earhook must be connected to use the headset.
Using ezTalker digital Powering ezTalker digital To Turn On the Headset 1. Press and hold the TALK button approximately four seconds until “On”, then “Standby” appears on the display, or until you hear the ON tone. The headset turns on and is placed in standby mode, ready to make and receive calls. Note: To conserve power, the display will turn off after being idle for 18 seconds. To view the display, simply press any button. To Turn Off the Headset 1.
Icons 7148321266 Caller ID Tekkeon Caller Name Ring... Status The icons in the first two positions will change according to the mode.
Making Calls You can make calls from your mobile phone, or directly from ezTalker digital using the last number redial feature, voice dialing commands, the stored number redial feature, or by accessing your mobile phone book from the headset (if these features are supported by your mobile phone). To Make Calls from Your Mobile Phone 1. Dial the number from your mobile phone. The call is automatically connected to your headset. To Make Calls Using Last Number Redial (if supported by your mobile phone) 1.
To Make Calls Using Stored Number Redial 1. With the headset off, press the VOLUME UP button to turn on the display and put the headset in stored number browse mode. The display will turn on. 2. Press the VOLUME UP button (forward) or VOLUME DOWN button (backward) to scroll through the numbers stored in your mobile phone until you reach the desired number. 3. Press the TALK button. The call is automatically connected to your headset.
Receiving Calls When you receive a call on your mobile phone, you will hear the mobile phone ring before you hear the ring tone through your headset as there is a small delay before the headset recognizes the incoming call. If you do not wish to answer the call, you can use the Call Reject feature to reject the call and send the caller to voice mail (if available). If the Call Waiting feature is supported by your phone, you can answer an incoming call while you are connected on another call.
Ending Calls 1. When you have finished your call, press the headset TALK button. The call will be disconnected. Transferring Calls You can transfer calls from your mobile phone to your headset, and from your headset to your mobile phone. To Transfer Calls from Your Mobile Phone to the Headset 1. Press any button on the headset to turn on the display (if off). 2. With the call connected to your mobile phone, press the TALK button on your headset. The call will be transferred to your headset.
Browsing the Phone Book Directly from your headset, you can browse and dial numbers stored on your mobile, if supported by your mobile phone. NOTE: Phone numbers stored on the phone (not on the SIM card) are displayed in the order they were stored on your mobile phone, not in alphabetical order. Some mobile phones only display the first number stored for a contact (such as home), and will not display all the numbers for that contact. This feature is supported by many phones.
To Enable Caller ID/Name 1. With caller ID disabled, simultaneously press the VOLUME UP and VOLUME DOWN buttons. “ID enabled” will appear on the display. Adjusting the Volume The volume can be adjusted using the volume controls on ezTalker digital or your mobile phone. To Increase the Volume 1. While in talk mode, press and release the VOLUME UP button. Repeat until you reach the desired level. The volume level icon will change accordingly. To Decrease the Volume 1.
Visual and Audible Indicators ezTalker digital uses visual and audible indicators to provide the status of the headset. For visual indicators, the headset provides caller ID, display icons to indicate headset state, connection status, and volume and battery level, and text and a blue LED that provide operation status. The icons are described in Understanding the Display, and the text and LED are described in this section.
Visual and Audible Indicators (continued) LED Status Indicators Status Indicates Flashes at two-second intervals Headset is in standby mode, ready to make and receive calls. Is off Headset is off. Audible Indicators Tone Indicates Double beep, increasing in pitch Headset has been turned on. Double beep, decreasing in pitch Headset is about to turn off. A beep every 32 seconds Battery is low. Double chime, followed by low beep Headset has been put into pairing mode.
Troubleshooting Issue Solution When you initiate the Bluetooth device pairing feature on your mobile phone, your phone cannot find ezTalker digital. Verify that ezTalker digital is placed in pairing mode (Pairing is shown on the display). If not, place the headset in pairing mode. Your ezTalker digital headset is not communicating with your mobile phone. Ensure that the headset is on and charged, and that you have paired the headset with your Bluetooth mobile phone.
Troubleshooting (continued) Issue Solution When you receive a call on your mobile phone, the call is not automatically connected to ezTalker digital after you press the TALK button. 1. Ensure that your ezTalker digital headset is charged and turned on. 2. Ensure that your Bluetooth mobile phone is set to Bluetooth mode, and that ezTalker digital (BTHS) has been selected as the connected Bluetooth device. (This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device.
Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will replace the defective product when the owner returns all product contents. The limited warranty will be considered void if the unit is tampered with, subject to misuse, negligence or accidental damage, has been improperly serviced, or if the security seal is removed.
FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Customer Support If you product is in need of repair or replacement, please contact the Tekkeon Customer Support Center at: Tekkeon, Inc. c/o ezTalker digital 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 www.tekkeon.com Tekkeon, Inc. will issue a Return Merchandise Authorization (RMA) number for all repairs or exchanges.
www.tekkeon.com © 2005 Tekkeon, Inc. All Rights Reserved ezTalker™ is a trademark of Tekkeon, Inc.