Cord-Free Headset for Mobile Phones ET2000 User Guide Bluetooth mobile headset
Inside Front
ezTalker mini by Tekkeon is a miniature cord-free headset that enables comfortable, handsfree communication with your Bluetooth mobile phone. ezTalker mini works with your Bluetooth-ready mobile phone to provide clear, high-quality communication. TM TM While using your ezTalker mini headset, you can store your mobile phone in your pocket, backpack, or briefcase—just about anywhere in close proximity that is convenient for you.
Getting to Know ezTalker mini TALK Button Used for turning headset on/off, pairing, and making/receiving calls Amber and Blue LEDs Provides visual indication of headset status: power on/off, pairing mode, muting mode, charging mode, and low battery Speaker Charging Jack Input for power adapter to charge the headset Volume Control Microphone Used to adjust the speaker volume, mute the microphone and initiate last number redial Getting Started Before using ezTalker mini, you must: • Charge ezTalker mini
Charging ezTalker mini Before using ezTalker mini, you must charge the headset for approximately two hours. When fully charged, the battery provides up to five hours of talk time and up to 120 hours of standby time. To Charge the Headset 1. Remove the rubber plug that covers the charging jack on the upper left side of the headset. 2. Plug the power adapter into the charging jack. 3. Plug the power adapter into a wall outlet. While the headset is charging, the amber LED on the headset will remain on.
To Pair the Devices 1. Turn on the mobile phone and place it next to the headset. 2. Initiate the Bluetooth device-pairing (discovery) feature on the mobile phone. Refer to the mobile phone user guide for instructions on initiating this feature. 3. With the headset turned off, press and hold the TALK button approximately five seconds, until the blue and amber LEDs flash alternately or until you hear the PAIRING tone. 4. Release the TALK button. The headset is now in Pairing Mode. 5.
To Replace the ezFit Earpiece 1. To remove the ezFit Earpiece, hold the plastic and gently pull toward you. 2. Snap the other ezFit Earpiece into place. Figure 2. ezTalker mini with ezFit Earpiece To Add the ezEarhook 1. Position to hole on the end of the ezEarhook over the stem on the rear of ezTalker and push to snap the ezEarhook into place. 2.
To Turn Off the Headset When the headset is on, press and hold the TALK button approximately four seconds until the blue LED turns off or until you hear the OFF tone. The headset turns off. Making Calls You can make calls from your mobile phone, or directly from ezTalker mini using the last number redial feature or voice dialing commands (if these features are supported by your mobile phone.) To Make Calls From Your Mobile Phone 1. Dial the number from your mobile phone.
Receiving Calls When you receive a call on your mobile phone, you will hear the mobile phone ring before you hear the ring tone through your headset as there is a small delay before the headset recognizes the incoming call. If you do not wish to answer the call, you can use the Call Reject feature to reject the call and send the caller to voice mail (if available). To Receive a Call 1. When you hear ring tone on your headset, press the headset TALK button.
Adjusting the Volume The volume can be adjusted using the volume controls on ezTalker mini or your mobile phone. To Increase the Volume 1. Press and release the top VOLUME button +. To Decrease the Volume Figure 4. Volume buttons 1. Press and release the bottom VOLUME button -. Muting ezTalker mini You can mute and un-mute the microphone temporarily so that you cannot be heard by the connected party. To Mute the Headset 1. Press and hold either VOLUME button (+/-) for three seconds.
Visual and Audible Indicators Two LEDs (blue and amber) indicate the status of the headset, while tones heard through the headset provide an audible indication of a requested action. Following are descriptions of visual and audible indicators provided by your ezTalker mini headset. Visual Indicators LED Status Indicates Blue LED flashes at two-second intervals Headset is in standby mode, ready to make and receive calls. Blue and amber LEDs flash alternately Headset is in pairing mode.
Troubleshooting Issue Solution When you initiate the Bluetooth device pairing feature on your mobile phone, your phone cannot find ezTalker mini. Verify that ezTalker mini is placed in Pairing Mode (blue and amber LEDs are flashing alternately). If not, place the headset in Pairing Mode. Your ezTalker mini headset is not communicating with your mobile phone. Ensure that the headset is on and charged, and that you have paired the headset with your Bluetooth-enabled mobile phone.
Troubleshooting (continued) Issue Solution Even though your headset is turned on, the call is not automatically connected to ezTalker mini when you dial a number on your mobile phone. 1. Ensure that your Bluetooth mobile phone is set to Bluetooth mode, and that ezTalker mini (BTHS) has been selected as the connected Bluetooth device. (This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device.) 2.
Disclaimer of Warranties Any user of this product does so at the user’s own risk. To the maximum extent permitted by applicable law, Tekkeon, Inc.
FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
www.tekkeon.com © 2004 Tekkeon, Inc. All Rights Reserved Rev.