User's Manual

ManualsBrandsTekelek Europe ManualsElectronics888 Module

TEK 888 Module User’s Manual

FCC ID: S6T888

IC: 20606-888

APPROVED EXTERNAL ANTENNA TYPES

Transmitter Antenna (from Section 7.1.2 RSS-Gen, Issue 5) The 888 module can only be sold

or operated with antennas with which it was approved. Transmitter maybe approved with

multiple antenna types. An antenna type comprises antennas having similar in-band and out-of-

band radiation patterns. Testing shall be performed using the highest gain antenna of each

combination of transmitter and antenna type for which approval is being sought, with the

transmitter output power set at the maximum level. Any antenna of the same type having equal

or lesser gain as an antenna that had been successfully tested with the transmitter, will also be

considered approved with the transmitter, and may be used and marketed with the transmitter.

When a measurement at the antenna connector is used to determine RF output power, the

effective gain of the device's antenna shall be stated, based on measurement or on data from

the antenna manufacturer. For transmitters of output power greater than 10 milliwatts, the total

antenna gain shall be added to the measured RF output power to demonstrate compliance to

the specified radiated power limits

RF Trace Layout Design

The modular transmitter is certified with a PCB edge SMA connector and micro-strip trace layout as shown

in the figure. The left side RF path is not used for this module. The host PCB can follow these trace design

to maintain compliance under the modular grant (FCC) and certificate (IC).

RF TRACE ROUTNG (TOP LAYER)

Summary of content (9 pages)

PAGE 1
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 APPROVED EXTERNAL ANTENNA TYPES Transmitter Antenna (from Section 7.1.2 RSS-Gen, Issue 5) The 888 module can only be sold or operated with antennas with which it was approved. Transmitter maybe approved with multiple antenna types. An antenna type comprises antennas having similar in-band and out-ofband radiation patterns.
PAGE 2
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 RF TRACE ROUTNG (BOTTOM LAYER) 2
PAGE 3
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 HOST PRODUCT TESTING GUIDANCE from KDB 996369 D04 The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually. it should not be necessary for the host installer to re-test all the available transmitter modes or settings.
PAGE 4
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 United States The module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C “Intentional Radiators” modular approval in accordance with Part 15.212 Modular Transmitter approval.
PAGE 5
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 A user's manual for the finished product should include the following statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 6
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 antenna type and antenna gain (equal to or less than) is used. Testing of the module was performed with the antenna types listed in this manual.
PAGE 7
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 Canada The module has been certified for use in Canada under Industry Canada (IC) Radio Standards Specification (RSS) RSS-247 and RSS-Gen. Modular approval permits the installation of a module in a host device without the need to recertify the device. LABELING AND USER INFORMATION REQUIREMENTS Labeling Requirements for the Host Device (from Section 3.2.
PAGE 8
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
PAGE 9
TEK 888 Module User’s Manual FCC ID: S6T888 IC: 20606-888 transmitter, will also be considered approved with the transmitter, and may be used and marketed with the transmitter. When a measurement at the antenna connector is used to determine RF output power, the effective gain of the device's antenna shall be stated, based on measurement or on data from the antenna manufacturer.