Digital Satellite Receiver TCT 1500 User Manual SAT 4000 kanäle Digital audio Update via USB OTA 1.
PART 2 • English 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 2 2 2 3 2.0 Your Receiver 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control Unit 2.4 Default PIN code: 0000 2.5 Installing the Batteries 2.6 Using the Remote Control 3 3 3 3 4 4 4 3.0 Connections 3.1 Basic connection with SCART cable 3.2 Connecting to Satellite Dish 3.3 Connecting to a Digital Audio Amplifier 3.4 Connecting to USB device 4 4 4 4 4 4.
PART 2 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 2 • English WARNING: The batteries should not be recharged, disassembled, electrically shortcircuited, be mixed or used with other types of batteries. If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH) types with low self-discharge to ensure long time operation of remote control. 1.5 Usage of external USB devices It is recommended to use USB 2.0 storage devices. TekComm cannot guarantee compatibility to all types of USB storage devices.
PART 2 • English 17. COLOURED BUTTONS For Teletext and further menu functions 18. TV/RADIO In viewing mode toggles between TV and radio mode 2.4 Default PIN code: 0000 Connecting multiple fixed dishes to your receiver using a DiSEqC 1.0 switch Fig. 8 3.3 Connecting to a Digital Audio Amplifier Connect your Digital Audio Amplifier with the S/PDIF connector on the back of the receiver Fig.7 2.5 Installing the Batteries Fig.
PART 2 • English This option allows you to enable Auto Time Zone or to disable Auto Time Zone. If switched ON, it will follow the time zone automatically where you are. Use tu to set Auto Time Zone to OFF/ON. 4.1.6 Time Zone try to get a high as possible signal for Strength and Quality.) 4.2.1.2 DiSEqC 1.2/USALS DiSEqC 1.2/USALS need to be selected if your dish is mounted on DiSEqC 1.2 motor. a) First you need to set the LNB type you are using (YELOW button).
PART 2 • English For Toneburst OFF, you can edit 1 dish. For Toneburst ON, you can edit 2 dishes. Press pq to select Receiver and press OK. Here you can edit the dish settings. (Press the RED button to Add SAT you like to install.) Select a transponder receivable at your location (choose the Transponder field and select the transponder with tu). Now you can turn your dish to get the highest Strength and Quality level. If you have aligned your dish to maximum signal, press OK to save.
PART 2 • English 5.1.2 EPG (Electronic Programme Guide) The EPG shows the programme schedule for all services broadcasting EPG information. Note: Not all broadcasters provide programme information. Press pq to select the desired channel and the right screen will show you the available EPG. Press u to step in to the EPG schedule for the current channel and use pq for EPG± and tu to change Date. 5.3 Accessory In Main Menu press tu to move to Accessory and press OK to enter the menu.
PART 2 • English You can use Delete All to delete all channels from the list. RED = Add, GREEN = Del, YELLOW = Delete All, BLUE = Scan. (See bottom line.) 5.4.2 TV Setup Press pq to select TV Setup and press OK. Use pq to move to the following sub-menus TV Format, TV System, OSD Transparency, Banner Display Time and Video Output. 5.4.2.1 TV Format Press tu to change settings for TV Format (4:3 LB, 4:3 PS, 16:9 PB,16:9 AUTO). 5.4.2.2 TV System Press tu to change settings for TV System (PAL, NTSC, AUTO).
PART 2 • English NOTE: Your PIN code will change back to the factory setting “0000”. Press OK and confirm the new request “System Update?” and press OK for Yes or Exit for exit. 5.4.6 SW Update Warning! NEVER disconnect the USB device from the receiver, the receiver from the main or switch the power OFF during the update/backup procedure.
PART 2 • English tu and make your selection (Stereo, Left or Right channel). Press OK, Exit and confirm. Your selection will be memorized for the current channel. NOTE: Audio tracks containing AC3 can only be listened to if the receiver is connected to a digital audio amplifier and this amplifier is switched ON and set to the correct input. 8.0 Teletext Press TEXT in normal viewing mode and tu to increase or decrease the displayed page number. Use 1-9 buttons to input a page directly. 9.
PART 2 • English 10.0 Trouble Shooting There may be various reasons for occurring abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer. Don’t open the receiver cover. This may cause a dangerous situation and will void warrant Cause The display on front panel does not light up. Remedy The power cord is not plugged in. Receiver is in stand-by mode.
PART 2 • English 11.0 Specifications General Data Input Voltage Range: 100-240 V AC 50/60 Hz Demodulator Modulation: QPSK Power consumption: max 18W, typ. 4.5 W Input Symbol Rate: 2~45 Ms/s Operating Temperature: +0°C ~ 40 ° C SCPC /& MCPC signals from C & KU and satellites Storage Temperature: -30°C ~ 80°C Video Decoder Profile level: MPEG-2 MP@ML Input Rate: Max.
English PART 2 • English 13
PART 2 • English 14
