User Manual

ManualsBrandsTecom ManualsComputers & Accessories11N WLAN ADSL Router

- 1 -

Quick Installation Guide

AW4042U

4-Ethernet Port ADSL/ADSL2+ WiFi CPE

1. Install AW4042U

Back Panel

Fig. 1.1 the Back Panel of AW4042U

Label Function

DSL

RJ-45 connector: WAN interface to connect DSL line

USB

USB 2.0 connector: for printer and ext. Memory support

RJ-45 connector: Connect to the PC Ethernet port, or to STB

LAN 1- 3

RJ-45 connector: Connect to the PC Ethernet port.

RST

Reset button: Reset AW4042U to factory default setting.

DC-IN

Connect to the supplied power converter cable

Table 1.1 Illustration of AW4042U Back Panel

Summary of content (11 pages)

PAGE 1
Quick Installation Guide AW4042U 4-Ethernet Port ADSL/ADSL2+ WiFi CPE 1. Install AW4042U Back Panel Fig. 1.1 the Back Panel of AW4042U Label Function DSL RJ-45 connector: WAN interface to connect DSL line USB USB 2.0 connector: for printer and ext. Memory support TV RJ-45 connector: Connect to the PC Ethernet port, or to STB LAN 1- 3 RJ-45 connector: Connect to the PC Ethernet port. RST Reset button: Reset AW4042U to factory default setting.
PAGE 2
Front Panel There are 8 LEDs on the front panel which indicate the status of AW4042U showing as below: Fig. 1.
PAGE 3
Connecting the Hardware Before you begin, turn the power off for all devices. These include your computer(s), your LAN hub/switch (if applicable), and the AW4042U. WARNING The layout of the ports on your device may vary from the layout shown. Refer to the steps that follow for specific instructions. Figure 1.3. Overview of Hardware Connections 2. Login to AW4042U through web browser I. Configure your PC IP address as 192.168.1.x within the same subnet as AW4042U (AW4042U default IP is 192.168.1.
PAGE 4
Fig. 2.1 Login Dialog Box c. Enter the management Username/Password and click the OK button (The default Username/Password is admin/admin). d. The first page will show the first page of Quick Setup. Follow the instructions to configure the AW4042U. 3. Quick Setup I. Set up ATM PVC and QoS II.
PAGE 5
III. Enable/Disable Bridging Service IV.
PAGE 6
V.
PAGE 7
VI.
PAGE 8
5. USB To connect USB devices, the IAD provides an USB 2.0 port. I. Print Server AW4042U includes a print server that allows connecting one printer via USB. All PCs of the IAD have access to these printers. a. Go to Advanced Setup – Print Server to Enable Print Server Service b. Enter the Printer Name then Click Save/Apply c. Enter \\192.168.1.1 in the Web Browser and Locate the Network Printer in the Network.
PAGE 9
II. Network Storage AW4042U provides a file server utility, allowing you to manage (read/write/delete) files on a Network Attached Storage (NAS, i.e. hard disc or memory stick). AW4042U supports external hard discs up to a maximum of 5V/500mA which is 2.5W. When a hard disc needs more power, then this hard disc needs an own power supply. AW4042U does support FAT32, NTFS and Linux/Unix (EXT2 / 3) file system. a. b. Connect the USB Hard Disk or Memory Stick to the USB Port Enter \\192.168.1.
PAGE 10
6. Change Password Click “Management-> Access Control->Passwords”, input the data and click “Save/ Apply” Fig. 6.1 Access Control--Passwords 9. Wireless Click “Wireless”, input the data and click “Save/ Apply” as Figure 9.1 Wireless -- Basic . Figure 9.
PAGE 11
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.