2.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Revision and Amendment Records Revision # 01 02 03 Description 1. Preliminary Manual 1. Add New Function Setting --- Auto Pick up and Release Call. (Item-5 and 6 of Section-III) 2. Add Extra Function (Section-IV) 1. Modify the Auto Pick Up and Release Call. (Item-5 and 6 of Section-III) 2. Modify the Sleep Mode Status.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Table of Content I. Introduction........................................................................................... 4 II. System Installation .............................................................................. 6 1. Easy Installation .......................................................................................................................6 2.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 I. Introduction The cordless DK EKT system must connect to the Tecom DK System. It will provide powerful and convenient cordless function for business user. There are 2 EKT lines from KSU to the base in the cordless system. If the handset ID is #1, it means the handset is connected to the Line#1. If the handset ID is #2, it means the handset is connected to the Line#2.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 II. System Installation 1. Easy Installation The [Registration] programming will allow handset user to register the handset to the base unit. (1) First of all, enter the registration mode on the base unit. (2) And then, select the handset is in the registration mode, too. (3) Move the handset near the base. (4) The system will automatically register the handset and assign the handset ID.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 >LANGUAGE REGISTRATION And then, press [F1] or [F2] to select registration mode. >REGISTRATION DE-REGISTER And then, press [OK] key to enter registration mode, the LCD will display: REGISTRATION NO? Press [F1/F2] key to select the [YES?] mode. REGISTRATION YES? You can select [YES] to register, or [NO] to exit this mode. Press [F3] (the same as [OK] key) to confirm, the LCD will display: (e.g.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 REGISTERED HANDSET #1 Note: 1. There are 2 EKT lines from KSU to the base. 2. If the handset ID is #1 means the handset is connect to the Line#1. If the handset ID is #2 means the handset is connect to the Line#2. (4) If the registration function fails, the LCD will display: FAILED! TRY AGAIN! Note: If user wants to register again, he can follow the above procedure to re-register to base unit.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 base any more. There are 2 ways to de-register the handset unit. Operation Procedure for Method-A (Using the base only): (1) De-register all handsets Turn on the DIP SWITCH-1, SWITCH-2, and turn off the SWITCH-3. 1 2 3 ON After 5 second, the system will de-register all handsets. Note: The LED on the base will flash [Fast] when enter the de-registration mode.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Note: The LED on the base will flash [Fast] when enter the de-registration mode. (4) Finally, change the DIP SWITCH on the base changes to normal mode. (All switches are OFF) 1 2 3 ON Note: The LED on the base will flash [Normally] when the unit comes back to normal mode. Operation Procedure for Method-B (Using the base and handset): (1) The base is in the idle mode.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 You can select [YES] to de-register, or [NO] to exit this mode. Press [F3] (the same as [OK] key) to confirm, the LCD will display: (e.g. [YES]) (( )) DE-REGISTERING. PLEASE WAIT! If the de-registration is successful, the LCD will display: (( )) DE-REGISTER OK! If the de-registration fails after about 20-30 seconds, the Handset LCD will display: (( )) FAILED! TRY AGAIN! Note: 1.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 PLEASE REGISTER! 5. About the De-Register, please refer to the part of the programming mode for further detail. Subject: Quick System Setup and Reference Guide for Cordless DK Telephone System Author: SOHO Department, CPE R&D Division, TECOM Email: ytli@tecom.com.tw Date: Jul.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 III. Programming Setting (Handset) The system provides programming mode to set up more friendly features.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Press [F3] (the same as [OK] key) to enter the change mode, the LCD will display: (( )) LANGUAGE ENGLISH Press [F1] key to change the item. (Or, [F1/ F2] to select the other language) (( )) LANGUAGE FRENCH Press [F3] (the same as [OK] key) to confirm, the unit will generate the confirmation beep.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 The [Registration] programming will allow handset user registers to the base unit.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 REGISTERED HANDSET #1 Note: You can refer to the part of System Installation for further detail. 3. De-Registration Programming by the Handset If user doesn’t use the handset any more or wants to register the handset to the other base, it may be necessary to cancel the registration to original base. Only one handset can de-register to the base at a time.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Press [F3] (the same as [OK] key) to confirm, the LCD will display: (e.g. [YES]) (( )) DE-REGISTERING. PLEASE WAIT! If the de-registration is successful, the LCD will display: (( )) DE-REGISTER OK! If the de-registration fails after about 20-30 seconds, the Handset LCD will display: (( )) FAILED! TRY AGAIN! Note: 1. The base doesn’t need to enter the de-registration mode.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 (( )) >VIBRATION AUTO PICK UP Press [F3] (the same as [OK] key) to enter the change mode, the LCD will display: (( )) VIBRATION √RING √VIBRATOR Press [F1/F2] key to change the item.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 => …]. And, if press [F2] key, the change sequence is [RING + VIB => VIBRATOR => RING => RING + VIB => …… ]. 5. Auto Pick Up Programming The [Auto Pick Up] Programming will allow user to pick up the phone call by receiver or handsfree mode when user lifts the handset from cradle. There are 3 modes for [Auto Pick Up] programming mode. The select item: RECEIVER, HANDSFREE, and DISABLE. Default: RECEIVER.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Press [F3] (the same as [OK] key) to confirm, the LCD will display: (Select [Handsfree] mode) (( )) AUTO PICK UP HANDSFREE OK! 6. Release Call Programming The [Release Call] Programming will let user can programmable release the phone call in speakerphone mode by TALK key or SPEAKER key. There are 2 modes for [Release Call] programming mode. The select item: [BY TALK KEY] and [BY SPKR KEY].
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 Press [F3] (the same as [OK] key) to confirm, the LCD will display: (Select [SPKR] mode) AUTO PICK UP BY SPKR KEY OK! 7. Reset Handset Programming The [Reset] Programming will reset the handset unit back to the default status.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 (( )) RESETTING... PLEASE WAIT! After 3 seconds, the handset comes back to the default status. And, the LCD will display the following message for 5 – 10 seconds. INITIALIZING...
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 IV. Extra Function Information The cordless system will provide more information for RF Link status and Battery Power status. User can easily find the current handset status about the RF Link and Batter status. Note: 1. All new information about RF and Battery status will be displayed on the row-1 of the LCD. 2. The row-2 and 3 of the LCD display won’t be affected. 1.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 User must come back to near the base, or the call will be dropped within 30 seconds. 3. No Link to Base Status If the handset is put far away from the base or the power of the base unit is removed, the handset will display [NO LINK TO BASE] to indicate the handset can’t link with the base. Of course, the row-2 and row-3 of the LCD won’t receive information from base.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 5. Sleeping Mode Status For power saving issue, the handset will enter sleeping mode automatically when there is no special event in the system. The row-3 of the LCD will display handset extension number for user’s reference. But the row-2 will be blank to extend standby time. (( )) EXT 10 User can simply press any key to wake up the unit.
TECOM CO., LTD. 23, R&D ROAD 2, SBIP HSIN-CHU, TAIWAN, ROC PHONE: +886-3-577-5141 FAX: +886-3-579-7196 When handset in the key locked mode and long keypress [Flash], The LCD will display 3 seconds as follows: TO UNLOCK? PRESS [F3] If user presses the key [F3] within 3 seconds, the handset will be key unlock. Note: The [Flash] key will be changed to [TRANSFER] key in some models. So, LCD will display when user presses [TRANSFER] for 2 seconds: LONG KEY PRESS [TRANSFER] TO UNLOCK 7.