USERS MANUAL VHF Transceiver TM-8102 / TM-8104 UHF Transceiver TM-8402A / TM-8404A TM-8402B / TM-8404B * Version #1 (2011-05-16) 1
11535 W, 83rd Terrace Lenexa, KS 66214 Table of Contents 1. Safety / Warnings ---------------------------------------- 3 2. Feature ---------------------------------------- 7 3. Appearance of TM-8000 Series Mobile Radio -------------- 8 4. Controls & keys --------------------------------------- 9 5. Menu Description --------------------------------------- 16 6. Terminal Description --------------------------------------- 25 7.
1. Safety / Warnings Notices ◆ Government law restricts the operation of unlicensed radio transmitters within government controlled territories. ◆ Illegal operation is punishable by fine or imprisonment or both. ◆ Refer service to qualified technicians only. ◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Shut OFF the transceiver while refueling or while parked in gasoline service stations.
or your dealer. Do not transmit with high output power for extended periods; the transceiver may overheat. Do not operate the transceiver when vehicle engine is stopped. The vehicle engine may not be started due to low battery. Do not use incompatible accessories from other manufactures. It could result in damage and or malfunction to the accessory and or to the radio.
RADIO FREQUENCY ENERGY SAFETY INFORMATION Your radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.
Electromagnetic Interference/Compatibility During transmissions, your XRADIO radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.
Installing the transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision. 1. Mark the position of the hole in the dash, using the mounting bracket as a template. Using a 4.2mm(5/32 inch) drill bit, drill the holes, then attach the mounting bracket using the supplied screws.
Connecting Microphone 1. Insert the microphone plug into jack on the front panel of the transceiver. • Be sure the tab on the microphone plug is facing the left hand side. 2. Mount the microphone on the microphone hanger where it will be within easy reach of the user 3. To remove the microphone plug, press the tab on the connector while pulling the plug out of the transceiver jack Figure 1-2) Installation and Removing the Microphone Supplied Accessories Carefully unpack the transceiver.
discarding the packing. If any item are missing or have been damaged during shipment, file a claim the carrier immediately.
• Time-Out Timer (TOT) • Standard DTMF Encode and DTMF Decoder with ANI Function • Programmable Home Channel Function • Emergency & Built-in Emergency Microphone • Talk Around • Internal or External Speaker • Remote Radio Stun / Revive (Use 5 tone) • Ignition Function / Horn Alert / Public Address • 4W Front-Mounted Speaker • Heavy-Duty Microphone • Various Parameters and PC downloading methods • Built-in D-SUB15 Accessary Connector • PC Program Tuning 3.
Figure 4-1) Appearance TM-8000 Series Supplied Accessories Item Part Number Quantity ACC-810N : Programming Software(Narrow Band Only – United States Only) ACC-820NW : Programming Software(Narrow and Wide Band – Outside the USA) Acc-8025 : PC Programming Cable(USB) ACC-708 : Mobile Microphone 4.
Figure 5-1) TM-8102 / TM-8402 Front panel Figure 5-2) TM-8104 / TM-8404 Front panel Power ON/OFF Volume switch Press and hold the knob over 2 seconds to turn the mobile radio on and off. Rotate to adjust the volume level from 1 to 16. Turn it clockwise to increases the volume and counterclockwise to decreases the volume. When the knob is pushed less 2 seconds, Squelch can be changed. Display It is a 125x 36 Graphic type. Each icon indicates related operation.
Figure 5-2) TM-8000 Series LCD indicator Selector Rotate to select a channel. Clockwise increase the channel and counterclockwise decrease the channel. Press to select a group if the group is set. Press and hold to enter a menu mode over 2 seconds. Microphone Jack Insert the microphone plug into this jack. S Key Press the key to activate its programmable function. The default setting is RF power / Selcall. A Key Press the key to activate its programmable function. The default setting is Key tone/Menu.
Release to receive. 4.1 Programmable key functions Keys can be programmed with the functions listed below. The key can only be programmed with functions, depending on your use intention. Each key has two functions to be programmed, as long press and short press. Please contact your dealer for further details on the functions.
Rotate the volume knob clockwise to increase the volume and counterclockwise to decrease the volume. Maximum increment is 16 levels. Channel selection / Group selection Choose the wanted channel/group using the selector if it is programmed with group. To select a group, push the selector and move to the wanted group. And then push the selector at the wanted group as setting. Transmitting 1. Choose the wanted group and a channel. 2. Press and hold the PTT switch, then speak into the microphone.
1. Select the wanted group and channel 2. When a call is received, LED becomes green and re-adjust the volume as necessary. The user should not press the PTT during the reception. If 2/5 tones are programmed as close mode, without any matched tones, the radio doesn’t work normally. As it were, sending and receiving signals are prohibited until the matched tone is received. Scan To activate the Scan function, press the “B” key( at default setting ) or the key programmed as Scan over 2 seconds.
4.3 Advanced operations Selcall *At programmed selcall, paging between individuals or groups can be available with 5 tones. *Maximum 200 IDs’ can be memorized in the list. *To escape sellcal model, press and hold the selector over 2 seconds. No selcall operation Selcall operation 1) Call on selcall ID selection At call waiting, press the “S” key over 2 seconds at default setting or the key programmed as selcall. Rotate the selector to select the selcall channel you want to call.
Press a button programmed as Fast channel. Rotate the selector to change channels. Only channels programmed as Fast channel with ICON “F” is shown in the display. This function is activated when some channels in the channel list are selected as Fast channel by programmer and a button is pre-programmed as fast channel setting. Stun/Revive Stun status When Stun/Revive function is programmed with selcal ID, stunning a radio or reviving a radio can be activated by remote control.
This function is to alert people away from vehicle through external speaker when certain calls are received. Public Address This function is to route sounds from microphone to an external speaker or similar external equipment. Talk Around When communication through repeaters is performed, this function is to allow communication among radios directly if a repeater is out of range or out of order. 5. Menu Description To enter into the menu, press and hold the right knob for 2 seconds.
② Press the right knob to select Yes or No. ③ To go to upper rank, press the red button. 2) Priority Use ① Rotate the right knob(Encoder) to change Yes/No. ② Push the right knob(Encoder) to set, Back to upper menu. ③ To go to upper menu, press the Red button. 3) Priority List ① The channel list in the group and whether the channel is set as priority or not are displayed as the sign of Yes or No. To change channel in the list, rotate the right knob. ② Rotate the right knob(Encoder) to change Yes/No.
1) DTMF ① Rotate the right knob( Encoder) to select Yes or No. ② Press the knob to set, back to upper rank. ③ To move back to upper menu, press the red button. 2) SELCALL ① ② ③ Rotate the right knob(Encoder) to select Yes or No. Press the knob to set, back to upper rank. To move back to upper menu, press the red button. 5.3 Status Setting It is consisted of two kinds like “Send” or “Receive Check”. Pre-programmed Status is sent to the ID to be wanted receiving.
② Rotate the right knob(Encoder) to select the ID which you wanted to send the status. And then press the right knob(encode) to set. ③ After Automatically getting out of the menu, the radio send the status, a receiver’s ID and a sender’s ID orderly. 2) Receive Check ① Rotate the right knob to select the received status for reading. And then press the right know to check the sender’s ID. ② To remove the received status, press the “S” button.
① Rotate the right knob(Encoder) to select one of 4 step powers. And then press the right knob(Encoder) to set. ② To be back to upper menu, press the Red button. 2) Lone Worker ① Rotate the right knob(Encode) to select. And press it to set. ② To be back to upper menu, press the red button. 3) Scramble ① Rotate the right knob(Encode) to select. And press it to set. ② To be back to upper menu, press the red button. 4) Lcd Contrast ① Rotate the right knob(Encode) to select one of 20 steps.
② To be back to upper menu, press the red button. 6) Password ① When a Password is pre-programmed, ”PASSWORD INPUT” is displayed on the LCD. And input the password. So, below No.2 step will be processed. ② When a password is not programmed, “NEW PASSWORD” is shown on the LCD. So, input new password. ③ When “CHECKED PASSWORD” is shown, input new password one again. 5.5 Vehicle Setting It has two kinds.(Horn Alert, Public AD). Rotate the right knob( Encoder ) to select one of them.
② To be back to upper menu, press the red button. 2) Public AD ① Rotate the right knob( Encoder) to select “Yes”. And then press the right knob(Encoder) to activate it. ② To be back to upper menu, press the red button. 5.6 Sound/Tone There are 7 kinds of sub-menu. (ID Sound, Comapnder, Key Tone, Speaker, Name Tone, MSG Tone, Call Tone) Selection is done by the right knob(Encoder). Activation is by pressing the right knob. 1) ID Sound ① Rotate the right knob( Encoder) to select “Yes”.
3) Key Tone ① Rotate the right knob( Encoder) to select “Yes”. And then press the right knob(Encoder) to activate it. ② To be back to upper menu, press the red button. 4) Speaker ① Rotate the right knob( Encoder) to select one of them(Front, Back, Both). And then press the right knob(Encoder) to activate it. ② To be back to upper menu, press the red button. 5) Name Tone ① Rotate the right knob(Encoder) to select preferred tone. And then press it to set. ② To be back to upper menu, press the red button.
5.7 Repeater/Talk Around It is consisted of 2 kinds sub-menus.(Repeater, Talk Around). Selection is done by the right knob(Encoder). Setting is by pressing the right knob. 1) Repeater ① Rotate the right knob( Encoder) to select “Yes”. And then press the right knob(Encoder) to activate it. ② To be back to upper menu, press the red button. 2) Talk Around ① Rotate the right knob( Encoder) to select “Yes”. And then press the right knob(Encoder) to activate it.
6. Terminal Description ACC(D-SUB 15 Pin Connector) Pin NO Pin Name Description Specification I/O 1 DC+13.6V DC Power Output 13.6±15% O 2 IGN Ignition Signal Input Power ON : ↑ 8V I Remake Power OFF : ↓ 6V 3 EXT_SPK Loudspeaker Output 4Ω, 4Watt O 4 AF_OUT Audio Output 500mV O 5 EXT_MIC Audio Input 5㏀ I 6 TXD/FCN1 TX Serial Data 3.3V TTL O 7 RXD/FCN2 RX Serial Data 3.
4 PTT/TXD0 PTT/PC Serial Data 3.3V TTL I 5 ME MIC Ground MIC Ground - 6 MIC MIC Signal Input 600Ω I 7 HOOK/RXD0 HOOK/PC Serial Data 3.3V TTL I 8 DM MIC Data Detection High Impedance I/O Speaker Jack(3.5mm Phone Jack) 4Watt/4Ω Pin NO Pin Name Description Specification I/O 1 SPO External Speaker Output 4Watt/4Ω O 2 GND Ground Ground O Remake DC Input Power Connector Pin NO Red Black Pin Name Description Specification DC+13.6V DC Power Output 13.
Programmable Channels 256 Channels/32 Group Channel Spacing Dual Channel Spacing 12.5/25 KHz Dimensions 103mm (H)×52mm (W)×32mm (D) Weight 1.1Kg Power Source DC +13.6 ±15% Current Drain (maximum) Receive mode, rated audio out – 1A (Audio Max) Transmit mode – 11A Standby mode – 300mA Receiver Sensitivity 0.25uV 12 dB SINAD Squelch Sensitivity 0.22uV 10dB SINAD Selectivity 70dB (12.5KHz), 70dB (25KHz) Spurious and Harmonic Rejection 75dB FM Hum and Noise 40dB (12.
7.2 TM-8402 / TM-8404 General Frequency Range TM-8402A / TM-8404A : 400 ~ 475 MHz TM-8402B / TM-8404B : 450 ~ 520 MHz Frequency Stability ±1.5PPM (-30 to +60℃) Programmable Channels 256 Channels/32 Group Channel Spacing Dual Channel Spacing 12.5/25 KHz Dimensions 103mm (H)×52mm (W)×32mm (D) Weight 1.,1 Kg Power Source DC +13.6 ±15% Current Drain (maximum) Receive mode, rated audio out – 1A(Audio Max) Transmit mode – 11A Standby mode - 300mA Receiver Sensitivity 0.
