BEBCARE iQ
INDEX Features of Bebcare iQ…………………………………………………..........… 3 Warning……………………………………………………………………….…… 4 Control Layout and Icons………………………………………………………... 4 Icon Screen……………………………………………………………………….. 5 Power Supply……………………………………………………………………… 6 Pairing the camera to parent unit and movement sensor mat……………..… 8 Operation Camera……………………………………………………………………….....… 10 Parent unit……………………………………………………………………….… 12 Movement sensor mat…………………………………………………………….
Thank you for purchasing our Bebcare iQ digital WiFi baby monitor. Your unit has been manufactured and checked under the strictest possible quality control to ensure that each monitor leaves the factory in perfect condition. In the unlikely event you find any defects or have any problem, please contact our dealer or service center. Please read this manual carefully to obtain maximum performance and extended service life from the unit.
WARNING The Bebcare iQ should not be regarded as a medical device. Premature babies or those considered to be at risk should be under the supervision of your doctor or health personnel. Direct supervision of your baby at a regular interval by a responsible adult is strongly recommended in addition to using this baby monitor. CONTROL LAYOUT and ICONS 7 3 9 2 4 1 12 13 14 1. Power button 2. Power indicator Green - On Pulsating green -Ultra safe mode 3.
ICON SCREEN A Power Indicator Green - On Flashing Green - Battery low Red - Under Charging B Mic sensitivity I Carmera 2 C Movement sensor mat battery low J Temperature alarm on D WiFi on K Night light on L Night light VOX E Ultra safe mode on M Speaker mute F Baby’s room N Lullaby on temperature O Out-of-range/Talk back G Camera 1 P Baby breathing alert H Sound level meter (O+P) Movement sensor mat out of range 5
POWER SUPPLY (A) Camera 6 Insert the output plug of supplied 5V 1.5A AC adapter to USB port 6 . (B)Parent Unit (PU) Parent Unit FCC ID:OD9BC70PU 17 A Li polymer battery is already incorporated in the unit. To charge up the battery, connect the output plug of supplied 5V 600mA AC adapter to USB port 17 . With the unit being switched off, the power indicator icon A will light up red and will show up on icon screen fo 5 sec.
(C)Movement Senor Mat (optionally purchased) FCC ID:OD9BSM1 Set the lock lever to open position, slide open the battery door in direction as shown. Install 3 pcs AA (UM-2) alkaline batteries, observe correct polarities. Slide back battery door and set the lever back to lock position. The battery life can last for around 60 days when using battery such as Duracell.
PAIRING This process is the match the PU with camera and movement sensor mat so that they can communicate with each other while no other devices (even baby monitor of identical model) can interfere with you or receiving your signal. The PU and camera are already paired when they are shipped out from factory. However, it is necessary to perform pairing again when an extra camera is added to work with PU. 1. Press and hold the button 10 of PU. 2.
8. Switch off all units and switch on again, the baby monitor is ready for operation. 9. The pairing between camera and movement sensor mat should be performed after the successful pairing between camera and PU or otherwise the system will not operate properly. 10. Press and hold the volume up + button 8 on camera while switching on the unit by long press of power button 1 until the power indicator 2 starts flashing. 11.
OPERATION Camera 1. Follow the quick start guide to download the Bebcare iQ app and connect the camera to your home router. 2. Make sure to switch on the WiFi of camera using the button 14 on PU with D being shown on icon screen ( camera WiFi is default to be ON when shipped out from factory). Follow the steps as shown in the app. 3. Use the app to view the image as captured by camera lens. 4. Place the camera onto a stable location out of reach of baby (preferably 1m away).
8. This camera is incorporated with lullaby function which can be remotely turned on or off using PU or app. Parents can select from 6 different factory preset song/sound. The volume of music can be adjusted using the up/down button 8 which also control the parents’ talk back volume. 9. When there is sufficient light intensity, the app will show a colourful image.
Parent unit 1. Rotate the side ring 16 clockwise or anti-clockwise to switch on the unit (Clockwise – unit on with vibration/Anti-clockwise – unit on only). 2. The icon screen will show up for around 20 sec and if there is no sound from baby, the icons (except the power indicator icon ) will go off to save battery power. 3. Normally, the power indicator icon A will show green and when battery becomes low, it will start flashing green. Once the unit is under charge, this indicator will show red. 4.
Night light Use the buttons 12 15 to select between OFF, ON or VOX (on when detecting a sound). Press button 10 to confirm. Once ON or VOX is selected. The screen will show following: or N.B. The lullaby playing and night light status in PU and app will synchronize with each other when the setting is changed in either side. Temperature alarm Use the buttons 12 15 to select between ON/OFF, press 10 to confirm.
Camera microphone sensitivity Use the buttons 12 15 to select between level 1 to 5, press button 10 to confirm. Higher level means the microphone is more sensitive to baby’s voice. Breathing alert This feature is useful when the camera is paired to a movement sensor mat. Use the buttons 12 15 to select between ON or OFF, press button 10 to confirm. ON – The PU will monitor the breathing movement of baby and P will show up on icon screen.
5. Place the PU at a reasonable distance away from camera to avoid feedback. Too close a distance will create a screeching sound at the speaker 18 . 6. Once the PU receives a signal, the icon screen will light up and depending the signal is coming from which camera, the corresponding camera no. will show up together with other information (room temperature, WiFi mode or ultra safe mode, etc.) of that camera. N.B. In case the PU is paired to only one camera, the icon screen will not show the camera no. 7.
8. If the PU is paired to work with two cameras, camera 1 always has top priority. This means while the unit is listening to signal from camera 2, in case camera 1 starts transmitting, PU will immediately switch listening to camera 1 until it stops to transmit, then PU will switch back to listen to camera 2 . 9. To avoid parent missing the attendance to camera 2, while PU is listening to signal from camera 1, in case camera 2 starts to transmit, “2” will show flashing on icon screen to alert parent.
13. In case the temperature alarm is set to ON, whenever the baby’s room temperature falls outside the range as prescribed by the high and low temperature limits set in the app, an alarm will be heard and temperature reading starts flashing on icon screen. 14. It is possible for parent to talk back to baby to soothe his emotion. Press and hold the button 11, O show up on icon screen. Speak towards the microphone 13 . Release button 11 after finish speaking.
Movement Sensor Mat 1.Place the movement sensor mat underneath the mattress, lengthwise direction and directly under where your baby sleeps. For optimum performance, there should be no bedclothes tucked between the sensor mat and the mattress. Besides, if the mattress support is too soft (such as box spring or underpadding), a hard board is required to be placed underneath the mat to provide a firm surface for it. The size of the board should be larger than the sensor mat. Mattress 2.
3. For environment with continuous vibration from the floor, the sensor mat may has false detection and delay or prevent the alarm from sounding. Under such circumstance, move the crib to the corner of the room or near a solid supporting wall. Moreover, keep the crib away from strong draft and air current. 4.
N.B. In case there are two cameras operating in the system, besure each camera and its corresponding sensor mat are far away from each other and placed in separate rooms to avoid interfering each other and creating false alarm.
CHANGING THE OPERATION MODE OF CAMERA Use the button 14 on PU to change the different operation mode of camera : WiFi ON mode – the WiFi circuitry is switched on and parent can see baby’s image in app. D is shown in icon screen of PU. WiFi OFF mode – the WiFi circuitry is switched off and parent unable to see baby in app. Under such mode, there is less radiation from camera and no risk of being hacked. D goes off in icon screen of PU.
N.B. When changing from WiFi OFF to WiFi ON mode, the WiFi indicator 3 on camera as well as D on PU icon screen will show flashing. It will take around 20 - 30 sec for camera to be successfully connected to your home router. Once the WiFi indicator 3 and D light up steady, the connection is done and parents are able to view baby in app.
PRECAUTIONS -Use only the supplied AC adapters, use of other adapters may cause damage to the baby monitor. -When not using the monitor for a long period of time, remove all batteries from movement sensor mat to avoid damage due to battery leakage. -Disconnect the AC adapter from the wall outlet when the monitor is not to be operated. -Do not open the cabinet, no serviceable parts inside.
STANDARD ACCESSORIES a. Camera b. Parent unit with belt clip c. Stand for PU d. Instruction manual e. 3.7V Li polymer rechargeable battery pack (installed in PU) f. 5V AC adapters x 2 g. Lanyard x 1 a. b. e. c. f. d. g.
TROUBLE SHOOTING GUIDE Problem Possible Causes Solution Unable to see baby's image in app - Camera WiFi is off - Switch on WiFi using button 14 on PU - Input correct password in app - Swith off home router and reboot after 1 min - Perform set up process again “start with pairing to add camera” - Change to another ISP that has bandwidth over 20 Mbps - Password is incorrect - Home router is down - Camera is not connected to router - Your home internet has network bandwidth of less than 8 Mbps - Camera o
TROUBLE SHOOTING GUIDE Problem Possible Causes Solution and always show flashing - Sensor mat is off - Switch on sensor mat using movement senitivity knob 20 - Replace with new battery - Battery of sensor mat is running down - Distance between BU and mat exceed 10m - Move BU closer to sensor mat - Battery has run down - Recharge battery using AC adapter - Battery pack is damaged - Consult your dealer to change new battery Battery life is short - Vibration alert is swiched on - Switch off vibra
DECLARATION OF CONFORMITY 27
SPECIFICATION Camera 1080P High Definition Full HD true colour video IEEE 802.11 b/g/n WiFi specifications Lens with 100° view angle 330° pan and 110° tilt movement angle 5V 1.5A DC power supply Parent unit 30 hours of battery standby time (fully charged condition) 3.7V 800mAh Li battery installed 5V 600mA DC power supply This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
FCC W arning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.