User's Manual

Wireless
Charger
For more information on the Qi, wireless charging, Qi™ Charging
Standard and a list of compatible smartphones, please visit:
www.TYLT.com/VÜ
©2014 TYLT. All rights reserved. TYLT
®
and the TYLT
®
logo are
registered trademarks of Foreign Trade Corp. Other marks are
the property or their respective owners.
IC3603
SPECIFICATIONS -
Input: 5V, 1.8A • Output: 5V, 1A
CAUTION
The Vu Solo is for charging wireless charging
enabled and Qi™ Charging Standard compatible
smartphones only. The charging unit should
only be used at normal indoor room conditions.
Place charger on a hard at surface. For best
results, use the supplied USB power cable and a
5V USB power supply with an output power of
1.8A or greater. Vu Solo may become warm
during charging. Avoid direct contact with
highly ammable materials. Avoid contact with
delicate furniture nishes.
CARE AND MAINTENANCE
GENERAL - Keep Device Dry. Do NOT expose the
device to liquids. If device gets wet, immediately
unplug it and allow it to dry. Do not disassemble or
attempt repair.
Do not store the device in high or low temperatures.
STICKY SUCTION - Place Charger on a dry,
clean, at, smooth surface. It will adhere
immediately without any pressure needed. To
remove, pull up one corner slowly and gently. Be
Patient. To clean sticky suction, use soft, damp cloth
or scotch tape. Do NOT use solvents, alcohol or
cleaners.
POWERING DEVICE
Power-up the Vu Solo by inserting the included
Micro-USB power cable into the power port. Insert
the included USB cable into a USB Power Supply.*
POSITIONING YOUR DEVICE
Place your Qi™ compatible device on the charging
pad to begin charging. To nd your devices
charging spot, keep your device centered on the
pad horizontally. Move your device forward or
to a devices features. Check www.tylt.com/vu-solo
for more information and a demonstration of
alignment.
LED INDICATOR
While in Standby mode, the LED is OFF. Solid green
LED indicates Vu Solo is delivering full power. Slow
blinking indicates limited power source.For best
performance, use a USB power supply that delivers
more current.
TROUBLESHOOTING
Under any type of electronic error condition, the
Green LED will begin to Blink. A fast blink indicates
a Fault. Remove the phone and place it back on the
Vu Solo. If problem persists, unplug the Vu Solo
from power source and re-connect it.
If LED is blinking slowly, power is being
transmitted, but may be slower than optimal. For
optimal results, use a USB power supply with a
power output of greater than 1.8A.
If the green LED is on but no power is being
received by the device, there may be a metal object
near the coils. Pick up the device and remove
foreign objects and place device back on the Vu
Solo. This is a safety feature and normal operation.
* Note: USB power supply is not included.
Vu Solo Wireless Charger
Micro-USB power cable
w/ Alignment Ledge
PACKAGE CONTENTSENG
backward slowly until your device starts charging.
If the device does not start charging, continue to
move your device slowly forward or backward,
stopping for 2 seconds every ¼ inch (or 5mm).
Once the device is charging, the alignment ledge
can be set to enable quick placement next time the
Vu Solo is used. Simply move the alignment ledge
forward until it touches the top of the devices.
CHARGING YOUR DEVICE
Next time the device is ready to wirelessly charge,
make sure the top of the device is touching the
ledge as you set it onto the pad, and charging
should begin seamlessly.
You can also use the alignment tabs located on
either side of the silicone pad to help visually align
SPECIFICATIONS -
Input: 5V, 1.8A • Output: 5V, 1A
CAUTION
The Vu Solo is for charging wireless charging
enabled and Qi™ Charging Standard compatible
smartphones only. The charging unit should
only be used at normal indoor room conditions.
Place charger on a hard at surface. For best
results, use the supplied USB power cable and a
5V USB power supply with an output power of
1.8A or greater. Vu Solo may become warm
during charging. Avoid direct contact with
highly ammable materials. Avoid contact with
delicate furniture nishes.
CARE AND MAINTENANCE
GENERAL - Keep Device Dry. Do NOT expose the
device to liquids. If device gets wet, immediately
unplug it and allow it to dry. Do not disassemble or
attempt repair.
Do not store the device in high or low temperatures.
STICKY SUCTION - Place Charger on a dry,
clean, at, smooth surface. It will adhere
immediately without any pressure needed. To
remove, pull up one corner slowly and gently. Be
Patient. To clean sticky suction, use soft, damp cloth
or scotch tape. Do NOT use solvents, alcohol or
cleaners.
POWERING DEVICE
Power-up the Vu Solo by inserting the included
Micro-USB power cable into the power port. Insert
the included USB cable into a USB Power Supply.*
POSITIONING YOUR DEVICE
Place your Qi™ compatible device on the charging
pad to begin charging. To nd your devices
charging spot, keep your device centered on the
pad horizontally. Move your device forward or
to a devices features. Check www.tylt.com/vu-solo
for more information and a demonstration of
alignment.
LED INDICATOR
While in Standby mode, the LED is OFF. Solid green
LED indicates Vu Solo is delivering full power. Slow
blinking indicates limited power source.For best
performance, use a USB power supply that delivers
more current.
TROUBLESHOOTING
Under any type of electronic error condition, the
Green LED will begin to Blink. A fast blink indicates
a Fault. Remove the phone and place it back on the
Vu Solo. If problem persists, unplug the Vu Solo
from power source and re-connect it.
If LED is blinking slowly, power is being
transmitted, but may be slower than optimal. For
optimal results, use a USB power supply with a
power output of greater than 1.8A.
If the green LED is on but no power is being
received by the device, there may be a metal object
near the coils. Pick up the device and remove
foreign objects and place device back on the Vu
Solo. This is a safety feature and normal operation.
* Note: USB power supply is not included.
Vu Solo Wireless Charger
Micro-USB power cable
w/ Alignment Ledge
PACKAGE CONTENTSFRA
backward slowly until your device starts charging.
If the device does not start charging, continue to
move your device slowly forward or backward,
stopping for 2 seconds every ¼ inch (or 5mm).
Once the device is charging, the alignment ledge
can be set to enable quick placement next time the
Vu Solo is used. Simply move the alignment ledge
forward until it touches the top of the devices.
CHARGING YOUR DEVICE
Next time the device is ready to wirelessly charge,
make sure the top of the device is touching the
ledge as you set it onto the pad, and charging
should begin seamlessly.
You can also use the alignment tabs located on
either side of the silicone pad to help visually align
SPECIFICATIONS -
Input: 5V, 1.8A • Output: 5V, 1A
CAUTION
The Vu Solo is for charging wireless charging
enabled and Qi™ Charging Standard compatible
smartphones only. The charging unit should
only be used at normal indoor room conditions.
Place charger on a hard at surface. For best
results, use the supplied USB power cable and a
5V USB power supply with an output power of
1.8A or greater. Vu Solo may become warm
during charging. Avoid direct contact with
highly ammable materials. Avoid contact with
delicate furniture nishes.
CARE AND MAINTENANCE
GENERAL - Keep Device Dry. Do NOT expose the
device to liquids. If device gets wet, immediately
unplug it and allow it to dry. Do not disassemble or
attempt repair.
Do not store the device in high or low temperatures.
STICKY SUCTION - Place Charger on a dry,
clean, at, smooth surface. It will adhere
immediately without any pressure needed. To
remove, pull up one corner slowly and gently. Be
Patient. To clean sticky suction, use soft, damp cloth
or scotch tape. Do NOT use solvents, alcohol or
cleaners.
POWERING DEVICE
Power-up the Vu Solo by inserting the included
Micro-USB power cable into the power port. Insert
the included USB cable into a USB Power Supply.*
POSITIONING YOUR DEVICE
Place your Qi™ compatible device on the charging
pad to begin charging. To nd your devices
charging spot, keep your device centered on the
pad horizontally. Move your device forward or
to a devices features. Check www.tylt.com/vu-solo
for more information and a demonstration of
alignment.
LED INDICATOR
While in Standby mode, the LED is OFF. Solid green
LED indicates Vu Solo is delivering full power. Slow
blinking indicates limited power source.For best
performance, use a USB power supply that delivers
more current.
TROUBLESHOOTING
Under any type of electronic error condition, the
Green LED will begin to Blink. A fast blink indicates
a Fault. Remove the phone and place it back on the
Vu Solo. If problem persists, unplug the Vu Solo
from power source and re-connect it.
If LED is blinking slowly, power is being
transmitted, but may be slower than optimal. For
optimal results, use a USB power supply with a
power output of greater than 1.8A.
If the green LED is on but no power is being
received by the device, there may be a metal object
near the coils. Pick up the device and remove
foreign objects and place device back on the Vu
Solo. This is a safety feature and normal operation.
* Note: USB power supply is not included.
Vu Solo Wireless Charger
Micro-USB power cable
w/ Alignment Ledge
PACKAGE CONTENTSITA
backward slowly until your device starts charging.
If the device does not start charging, continue to
move your device slowly forward or backward,
stopping for 2 seconds every ¼ inch (or 5mm).
Once the device is charging, the alignment ledge
can be set to enable quick placement next time the
Vu Solo is used. Simply move the alignment ledge
forward until it touches the top of the devices.
CHARGING YOUR DEVICE
Next time the device is ready to wirelessly charge,
make sure the top of the device is touching the
ledge as you set it onto the pad, and charging
should begin seamlessly.
You can also use the alignment tabs located on
either side of the silicone pad to help visually align
RING D
he Vu Solo by insertin
p
ower ca
bl
e into t
h
e
d USB cable into a US
T
I
O
NIN
G
Qi™ comp
p
g
nment Le
d
ge
n
cluded
p
ort. Insert
r Supply.*
e chargin
Once th
can be se
V
u So
l
o
i
f
orward
CH
Next t
y
ce is charging, the alignm
enable quick placement ne
ed. Simply move the alignm
it touches the top of the d
ING YOUR DEVICE
e device is ready to wireless
e top of the device is touch
et it onto the pad, and ch
NDICATOR
ndb
y
mode, the LED is
O
es Vu Solo is delivering fu
icates
l
i
m
e, use a USB power s
nt
.
SHOOT
y
pe o
f
e
l
will begin
S
olid green
ower. Slow
F
or
b
es
t
hat delivers
tion, the
k indicat
p
If the gr
received
n
ear t
he
f
orei
g
n
o
Solo. Thi
ED is on but no power is b
he device, there may be a m
. Pick up the device and rem
ts and place device back on
safety feature and normal
nd allow it to dry. Do not
air.
e the device in high or low
Y
SUCTI
O
mooth surface. It wi
y without any pressu
l
up on
e
lean sti
c
pe. Do N
smart
only be
P
lace c
resu
l
ts
,
5V USB
1.8A o
ssemble or
mperatures.
n
a
d
ry,
e
ed
. To
ently. Be
damp cl
hol or
only. The charging unit
d at normal indoor room co
er on a hard at surface. Fo
the supplied USB power ca
wer supply with an output p
ater. Vu Solo may become w
ging. Avoid direct contact w
mable materials. Avoid con
re nishes
RING D
he Vu Solo by insertin
p
ower cable into the
d USB cable into a US
T
I
O
NIN
G
Qi™ comp
p
g
nment Led
g
e
n
cluded
p
ort. Insert
r Supply.*
e chargin
Once th
can be se
V
u Solo
i
f
orward
CH
Next t
y
ce is charging, the alignm
enable quick placement ne
ed. Simply move the alignm
it touches the top of the d
ING YOUR DEVICE
e device is ready to wireless
e top of the device is touch
et it onto the pad, and ch
NDICATOR
n
db
y mo
d
e, t
h
e LED is
O
es Vu Solo is delivering fu
icates
l
i
m
e, use a USB power s
n
t.
SHOOT
y
pe o
f
e
l
will begin
S
o
l
i
d
green
ower. Slow
F
or
b
es
t
hat delivers
tion, the
k indicat
p
If the gr
received
n
ear th
e
f
orei
g
n
o
Solo. Thi
ED is on but no power is b
he device, there may be a m
. Pick up the device and rem
ts and place device back on
safety feature and normal
nd allow it to dry. Do not
air.
e the device in high or low
Y
SUCTI
O
mooth surface. It wi
y without any pressu
l up on
e
lean sti
c
pe. Do N
smart
only be
P
lace c
resu
l
ts
,
5V USB
1.8A o
ssemble or
mperatures.
n
a dry,
e
e
d. To
ently. Be
damp cl
hol or
only. The charging unit
d at normal indoor room co
er on a hard at surface. Fo
the supplied USB power ca
wer supply with an output p
ater. Vu Solo may become w
ging. Avoid direct contact w
mable materials. Avoid con
re nishes