Technicolor Delivery Technologies – www.technicolor.
1. Before you start Carefully read the Safety Instructions and Regulatory Notices document included in your package before continuing with the installation of your gateway. Caution! • Do not look directly into the fibre source or into the end of a connected fibre cable. • Do not bend the fibre cable. Overbending the fibre cable may cause internal damage to the fibre cable. • Do not touch the fibre cable ends. They must remain clean to ensure optimal performance. 2.
. Connect your gateway to the Broadband service Choose your installation method To connect your gateway to the Internet you can either: • Directly connect your gateway to your service provider’s fiber network. In this setup your gateway is used as Fiber gateway. Follow the instructions from “Option A: Connect as Fiber Gateway” on page 2. • Place your gateway behind another Internet access device. In this setup your gateway is used as local Ethernet router.
Option B: Connect as local Ethernet router WAN 1 Plug the Ethernet cable with the red connectors into the red Ethernet WAN port on your gateway. 2 Plug the other end of the Ethernet cable into the Ethernet port of your Internet access device. 4. Connect your telephones to your gateway Connect your corded phone or DECT base station to the green port. 5. Power on your gateway 1 Plug the connector of the electric power supply adapter into the power inlet port ( ) of your gateway.
2 Press the power button ( ) on the back panel. Wait until the LED becomes solid blue. This can take several minutes! Do not power off your gateway or unplug any cables! 6. Connect your network devices We recommend you to first connect one computer/tablet (if possible via a wired connection), then complete the rest of the procedure and as a final step connect the other devices. 6.1.
Your gateway supports band steering, a function that lets your gateway automatically select the best access point for each of your connected Wi-Fi devices. If band steering is enabled both access points will appear as one. Wi‑Fi settings label The label of your gateway provides useful information about your Wi‑Fi network: • The Network Name. This name is used to identify your Wi-Fi network. Some use the term SSID instead. • The Wireless Key. This key is used to secure your Wi‑Fi network.
4 After a few seconds, your Wi‑Fi device should be connected. If the WPS ( ) LED starts blinking fast, then your gateway could not connect your Wi‑Fi device. For more information, see “The WPS LED is blinking fast” on page 6. Connecting a Wi‑Fi device manually On your Wi‑Fi device, proceed as follows: 1 Open the list of available Wi‑Fi networks and select the entry that contains the Network Name from the label. 2 Your Wi‑Fi device will ask you to enter the Wi‑Fi key or password. 7.
.2. How to reset your gateway If at some point you want to restore the default settings, proceed as follows: 1 Make sure that your gateway is turned on. 2 Use a pen or an unfolded paperclip to push the recessed Reset button on your gateway for at least 10 seconds and then release it. 3 Your gateway restarts and applies the factory default settings. Technicolor Delivery Technologies – www.technicolor.com Copyright © 2020 Technicolor. All rights reserved.
SAFETY INSTRUCTIONS AND REGULATORY NOTICES BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONS Applicability These Safety Instructions and Regulatory Notices apply to: • Technicolor xDSL Modems & Gateways • Technicolor Fiber Modems & Gateways • Technicolor LTE Mobile Modems & Gateways • Technicolor Hybrid Gateways • Technicolor Ethernet Routers & Gateways • Technicolor Wi-Fi Extenders Using equipment safely When using this product, always follow the basic safety pr
Software and firmware use The firmware in this equipment is protected by copyright law. You may only use the firmware in the equipment in which it is provided. Any reproduction or distribution of this firmware, or any portion of it, without express written consent from Technicolor is prohibited. Software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement.
containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service. Cleaning Unplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
• When the attached cords are damaged or frayed. • If liquid has been spilled into the product. • If the product has been exposed to rain or water. • If the product does not operate normally. • If the product has been dropped or damaged in any way. • There are noticeable signs of overheating. • If the product exhibits a distinct change in performance. • If the product is giving off smoke or a burning smell.
RF exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation.
