FCC ID; MILLENNIUM-X Micro flex Slim/Mini Desk Top PC User’s Manual M/N: IMF" -6BXV3; Millennium" X-II MFI" -6BX V3; Millennium” X-III
FCC ID: MILLENNIUM-X INSTRUCTIONS MANUAL FEDERAL COMMUNICATIONS COMMISSION : INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of contents CHAPTER 1 INTRODUCTION CHAPTER 2 GETTING STARTED CHAPTER 3 SPECIFICATION 3.1 Motherboard specification 3.2 The Slim Size and Mini Desk Top PC Pentium II specification CHAPTER 4 INSTALLATION 4.1 Mini Desk Top PC system installation 4.2 Slim Size PC system installation 4.3 Mini Desk Top PC all-in-one ATX motherboard Jumper Settings 4.4 CPU Jumper installation 4.5 System memory installation table CHAPTER 5 AWARD BIOS SETUP 5.1 Load Award BIOS setup defaults 5.2 Award BIOS COS setup 5.
FCC ID: MILLENNIUM-X CHAPTER 1 INTRODUCTION Introduction This manual is suitable for both Slim Size PC and Mini Desk Top PC. . The motherboard is all-in-one designed with AGP VGA and 10/100M Network chip build-in. This motherboard is design for both Slim Size PC and Mini Desk Top PC, both and MFII'6BX are the new designed with ATX structure.
CHAPTER 2 GETTING STARTED About your Sim Size or Mini Desk Top Pentium II green PC, Once you have received the Limit's Size or Mini Desk Top PC, please check the following items: * *k Kx What's included Slim size or mini desk top case with ATX power supply installed. The Pentium II all-in-one ATX type motherboard preinstalled inside the slim size or mini desk top case.
Checking the AC input voltage before turn on the power switch, The AC input voltage can be switch from 110 Alts to 230 Volts or from 230 Volts to 110 Volts. The AC input voltage convert switch is located on the backside of the power supply. Please double check whether the AC input voltage is matching at your country or not. If it is the wrong voltage, please make the correct setting of this switch. Installing the CPU, if you order the system without CPU installed.
10. 11 Please refer to page No. 19 of this manual for the floppy disk installation of the slim size PC system installation. Installing the CD-ROM drive, If necessary. | Please refer to the step 10 of the Mini Desk Top PC system installation at page No. 14 of this manual for detailed CAROM driver installation. Please refer to page No. 18~19 of this manual for the slim CD-ROM installation of the slim size PC installation. Please refer to page No. 28 of this manual for the detailed BIOS COS SETUP.
FCC ID: MILLENNIUM-X CHAPTER 3 SPECIFICATION 3.1. Motherboard specification The motherboard is ATX type all-in-one designed with AGP VGA and 10/100M Network chip build-in. Following is the detailed feature of the motherboard designed. FEATURES ® Motherboard core logic ! Intel 82440BX + RIV 128ZX 128bit 3D AGP + RTL Co 8139A 10/100M FAST Ethernet + W83977 EF supper 1/0 controller + GL520SM temperature control.
On board supports two high speed ARTS 16C550x2 and multi-mode parallel port for standard, Enhanced EPP and high speed ECP modes. PS/2 mouse port with mouse wake-up function, PS/2 keyboard port with keyboard wake-up function. On board support for IR function. Supports two universal serial bus (USB) @® Network Built in RTL 8139A 10/100Mbps PCI FAST Ethernet on board with JR-45 connector and wake-up on LAN function. e AGAVE . . Built in RIV 128ZX chip 128bit 3D AGP VGA on board with 4MB GRAM.
2 Fan speed monitored 5 VID inputs + 4 type of speaker-driven signal output for different sound signal for CPU and system temperature, power supply voltage/CPU voltage and fan speed Sm Bus serial interface Read back capability of all monitored temperature, voltage and fan speed
3.2 The Slim Size and Mini Desk Top PC Pentium II Specifications: 1. CPU: Supports Intel Pentium II and Electron CPU up to 100MHz bus Frequency. Intel Electron 300/300A/333A Intel Pentium II 333/350/400/450 Auto detection of CPU voltage 2. Chip set: Intel 82440BX + RIV 1282X 128 bit 3D AGP + RTL 8139A 10/100M FAST Ethernet + W83977 EF supper I/O controller + GL.5208M temperature control. 3. Memory: Provides 2 DIM sockets to support 4MB/8MB/16MB/32MB/64MB/ 128MB/256MB DOCUDRAMA memory modules up to 512MB.
slots: Floppy disk: Hard disk: CD-ROM: Video output: Network: (option) Supports two universal serial bus (USB) Supports 4 slots VISA mixed for model. a. 4 ISA slots. b. 3 ISA and 1 PCI slots c. 2 ISA and 2 PCI slots. d. 118A and 3 PCI slots. Support 2 slots PHARISAIC mixed for model a. 2 ISA slots. b. 1 ISA and 1 PCI slots. ¢. 2 PCI slots. One 3.5” 1.44MB floppy disk drive with front bezel for model One 3.5” 1.44MB floppy disk drive without front bezel for model. (Hidden inside the case ) One 3.
Physical size: Power supply: Keyboard: Monitor: BIOS: Second fan: up on LAN function 33CM(L) x 32CM(W) x1 1ICM(H) for model 33CM(L) x 32CM(W) x 8CMH) for model. ATX power 200W. 110V/230V switchable. UL/CSA/TUV/VDE/DEMKO/ NEMKO/SEMKO/FIMKO/FI/ CB/CE/FCC approved. 84/85 keys mini keyboard or regular 101/102 keys keyboard or 105/106 keys WINDOWS 95 keyboard. PS/2 keyboard connector. 9” VGA mono or VGA color monitor or regular 147/157/17”° VGA mono or VGA color monitor or LCD display monitor. 2MB flash PROMOTE.
CHAPTER 4 INSTALLATION 4.1 Mini Desk Top PC system ~ installation The following is the Mini Desk Top PC system installation procedure step by step which will guide you to install the mini desk top PC system as much as easier. Please refer to diagram (1) of this page for detailed parts location of each step. STEP 18 WAIN BOARD i \ STEP 9 STEP 1S PHY 1 HOD STERN STEP 8 SEEP 243 X 0.
Step: Step: Step: Ste pd: Step: Open the case upper CORER. Installing the L shape power supply by screw in the 5 screws. Please refer to the diagram (1) for the power supply installation. . Installing the power switch by screw in the 2 screws. Please refer to the diagram (1) for the power switch installation. Installing the second fan by screw in the 4 screws. The second fan is located between the case front side panel and the front bezel. Please refer to the diagram (1) for the second fan installation.
Step: | Step: | Step: B | Step: Installing the front bezel into the case by screw in the 5 screws and push in the above wires (step and the second fan wire into the case to connect to the motherboard and the power supply. Please refer to the diagram (1) for the detailed front bezel installation, Installing the 3 supporting bracket on the lower case, please. refer to diagram (1) for the detailed supporting bracket installation. Installing the hard disk drive, if necessary.
Steppe: Step ll: Steeple: ¢. Connects the power cable to the floppy disk drive. The power cable is only one way direction. d. Align the floppy disk drive to be line up with the front bezel and screw in the 4 screws of the FDD side screws. Please refer to diagram (1) for detailed floppy disk drive installation. Installing the CD-ROM drive, If necessary. To install the CD-ROM drive, please follows the step below: a.
Steppe: Steeple: Steppe: Steppe: Steppe: Steppe: Steppe: Installing the motherboard into the case by slide in the motherboard horizontally with the base of the case until the VGA connector, printer port, Network port, PS/2 Keyboard port, 4 connectors matching up with holes of the back panel of this case, please make sure that the motherboard screw holes (total 5 screw holes) also matching up with base mounting holes of the case.
Steppe: Steeple: Steppe: Steppe: Installing VO cards on your Mini Desk Top PC, if necessary. The Mini Desk Top PC has the ability to install 4 VO cards either PCL or ISA or any combination. They can be either 4 ISA slots or 3 ISA slots + 1 PCI slot or 2 ISA slots +2 PCI slots or 1 ISA slot + 3 PCI slots. You can install any 1/0 card simply by taking the card horizontally and insert the gold finger inside the riser card, then screw in the card metal plate on the back slot windows mounting bracket tightly.
Steppe: Steppe: Steppe: Steppe: Up to now, you have finished the system installation of the mini desk top PC and you are ready to turn on the power lo operate your system. Hope everything is running well and you are very satisfy with your system. Congratulations! Installing the software driver, if necessary. There are two types software driver included in your system CD-ROM disk and you may need to install them when you are running your system.
4.2 Slim Size PC System installation The MFI-6BX Slim Size PC system installation procedure will be similar to the Mini Desk Top PC. Except the following devices need to do the special care. Slim CD-ROM installation The slim CD-ROM needs to install a small PC board which convert the IDE interface of the slim CD-ROM to the standard IDE interface of the motherboard. Following is the block diagram of this converter board. rr 12 CON This connector is to connect the audio signal to the sound card.
Choose your slim CD-ROM bender and set the slim CD-ROM to the slave condition. Connects all the cables to J1, J2 and CON connectors. Ste pl. Installing the slim CD-ROM mounting bracket by screw in the 2 screws, on the holding bracket. Step. Screw in the 2 M2 screws between the slim CD-ROM mounting bracket and the converter board. 3 1/2” floppy drives installation.
4.3 Mini Desk Top PC all-in-one ATX Motherboard Jumper Settings. To setup the Mini Desk Top PC all-in-one ATX motherboard jumpers, please refer to the diagram (2) at this page for detailed jumper location. Tr GE coz Lp = CONS] IPS CON J2 a COM Tow cot WP2 489 TTT DIM — DIMMED 3711 DIAGRAM (2) THE SLIM SIZE/MIMI DESK TOP PC ALL-IN-ONE ATX MOTHERBOARD JUMPER LOCATION V1.
J1: PS/2 Mouse Connector Pin No. Function 1 Mouse clock 2 vce ” 3 Mouse data 4 NC 5 GND CONT: PS/2 Keyboard Connector Pin No.
9, J2: USB Port connector Ee Pin no. | Function Port 1 Pin 1 Pin 2 Pin 3 Pin 4 Port 2 Pin Pin 6 Pin Pin 8 10. 15: ATX Power Connector Function Pin No. Pin 10 Pin 20 Finley Pin 18 Pin 17, Pin 16 _[Pins [GNI Pin 14 11. RESET: Reset Switch 12. IR: Ir DA SIR or FIR Connector GND Pin No. {Function {Infrared Data Input ( (kilobytes for SIR) “infrared Data Output VEC (+5V) Infrared Data Input (4M Bytes for FIR) 13. J9: Floppy Disk Drive Connector 14.
COM: Serial Port COM Connector PRAT: Printer Port Connector LANCED: LAN LED (TX/RX) . Pin: Cathode Pin: Anode It will light on when the data is transmitting or Receiving.
by some sound cards from that the PCI Bus. Your sound card package should include a cable for this feature if it . requires. SILK! Pin Assignment onto + 0 0+ 2 Pond O + Oreo# Godsends TC 004 6 SERIES Slot 1: Pentium Deceleration CPU Riot. PWT: Power Button with password control. SOLED: Power Button without password control. Jil: Theorist temperature sensor for CPU cooling fan control.
4.4 CPU Jumper installation 1. JP: CPU Frequency Select 1-2 Short: CPU frequency auto detection, if set the (Default) jumper PIOUS a. 1-2 Short to pin 1-2 short, the motherboard will automatic detects the CPU frequency. In this case that you don’t need to install any CPU jumper for both 66MHz and 100MHz CPU. If 100MHz CPU installed, then it will run 100MHz automatically, while 66MHz installed, then it will RUN 66MHz.
2-3 Short; This is to run the CPU frequency at higher speed (over specs), if the 66MHz CPU installed, it will run 100MHz, please enter the chip set feature mine at the BIOS setup to select the CPU bus speed that you want to run over specs. [2 Short |100MHz |CPU HOSTILE CLOCK |DEFAULT l 12 Short |100MHz |CPU HOSTILE CLOCK {103/34 MHz 12 Short |100MHz [CPU HOSTILE CLOCK [112/33 MHz 1-2 Short |100MHz [CPU HOSTILE CLOCK [133/44 MHz 1-2 Short |100MHz [CPU HOSTILE CLOCK [100/33 MHz MF-6BX / MF-6BXV3A REV:2.