Manual

ManualsBrandsTechnaxx ManualsCar & BicycleTX-170 Wireless reversing camera system Automatic day/night switch, Proximity sensors, tiltable, IR add-on ligh

Technaxx

* User Manual

Wireless Rear Camera System TX-170

Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.)

as assistance for reverse parking.

This system should be an aid and should NOT replace the need to drive

carefully.

Do not point the high pressure cleaner directly to the plate holder

camera, or drive through a car wash - the device can be damaged.

Under no circumstances will the manufacturer or supplier accept any

responsibility or can held liable for any direct or indirect, incidental or

consequential damage, or for injuries resulting from installing or use of

this system.

The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares

that this device, to which this user manual belongs, complies with the

essential requirements of the standards referred to the Directive RED

2014/53/EU. The Declaration of Conformity you find here:

www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before

using the device the first time, read the user manual carefully.

Service phone No. for technical support: 01805 012643 (14 cent/minute from

German fixed-line and 42 cent/minute from mobile networks). Free Email:

support@technaxx.de

The support hotline is available Mon-Fri from 9 am to 1 pm & 2 pm to 5 pm

Keep this user manual for future reference or product sharing carefully. Do

the same with the original accessories for this product. In case of warranty,

please contact the dealer or the store where you bought this product.

Warranty 2 years

Enjoy your product. Share your experience and opinion on one of the

well-known internet portals.

Summary of content (16 pages)

PAGE 1
Technaxx® * User Manual Wireless Rear Camera System TX-170 Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.) as assistance for reverse parking. This system should be an aid and should NOT replace the need to drive carefully. Do not point the high pressure cleaner directly to the plate holder camera, or drive through a car wash - the device can be damaged.
PAGE 2
Contents Features ........................................................................................................ 2 Technical specifications ................................................................................. 3 Safety regulations .......................................................................................... 4 Product overview ........................................................................................... 4 License plate holder with camera ......................
PAGE 3
Technical specifications License plate holder with camera and wireless module Image sensor 1MP CMOS Camera resolution / fps 640x480 pixel / 30 Viewing angle 135° (V90° / D165°) Min. illumination 0.5Lux / automatic white balance IR night vision distance ~2m Power supply DC12-24V Max. current <140mA Power wire length Ca. 2.6m Transmission frequency 2.400-2485.5MHz Transmission distance ~15m open space (no interferences) Max.
PAGE 4
Safety regulations The reversing system is an aid and does not relieve the driver of his duty of care in road traffic according to STVO. Read these instructions carefully before first use. Product overview The rear view camera sends a video signal from the camera 2.4GHz frequency range (specified for such video transmissions) to the monitor. In case another Bluetooth handsfree device is installed in your vehicle, it works in the same frequency range as the camera.
PAGE 5
Monitor 1 2 3 4 Add (+) Menu/OK Dec (-) Screw for holder 5 Power connection (DC9V) 6 Holder 7 Display 4.3” (10.9cm) Commissioning Check the functionality of the components before installation (a installed product is excluded from the return). Preparing and installing the license plate holder. NOTE: You may need a voltmeter to measure the polarity of the reversing light.
PAGE 6
CAUTION! If you have no experience in installing electrical devices on vehicles, you are not allowed to carry out the following work yourself. Have the assembly and connection carried out by qualified specialists. 1. Remove your rear license plate including any holder that may be present. Instead of the built-in holder, mount the license plate holder with camera here - if possible using the old mounting holes. First hold it up to the vehicle and prepare for installation: 2.
PAGE 7
License plate holder installed to License plate holder installed to the trunk lid. the bumper. 6. Remove the cover of the reverse light. 7. The thin two-core cable is used for power supply and as a switching signal when reverse gear is engaged. Connect the two wires with the two contacts of your reversing light. To do this, you need to know their polarity (measure or check the circuit diagram): The red cable must be mounted on the positive pole of the reversing light and the black cable on an earth contact.
PAGE 8
Insert the license plate in the holder 1. Remove the cover strip from the license plate holder Note: First remove the middle part of the cover strip, then remove the two sides of the cover strip 2. Insert license plate into the holder, frame the license plate through the small bezels basically. 3. Insert the top cover strip's clips into the relative holes of the license plate holder then press tight.
PAGE 9
Installing the monitor 1. Monitor pedestal could be attached to stand or windshield as your requirements. There are 2 kinds of mounting brackets accordingly. Stand mount Suction cup mount 2. Mounting the brackets 1) If using the factory default stand mount, stick on the dash board: Choose and clean a right place on the dash board, tear the paper of the monitor stand sticky tape, put and press tight the stand mount on the dash board.
PAGE 10
Note: Look at the back of the monitor. Check if the roller cam is facing inward and the roller cam is in close contact with the groove of the bottom case of the monitor. The installation direction is correct. As shown in the figure, the monitor is viewed from the back side. If the roller cam faces outward, the installation direction is wrong. Choose a right place on the windshield and mount the suction cup mount on the windshield.
PAGE 11
Camera angle adjustment Put the car in reverse gear to automatically trigger the display of the image behind the car. Then adjust the camera angle to the most suitable position. Adjustable angle for flexibility: 114° When rotating the camera hold the license plate holder with one hand and rotate up or down the outer frame of the camera with the other hand to set the best angle.
PAGE 12
Monitor button & setting 1 The Up button (Add/+) - Short press to change/add parameter value at the menu setting interface. 2 The Middle button (Menu/OK) - Short press to enter monitor menu setting. - Long press (press and hold for 3 seconds) to confirm the chosen item in the menu setting interface. 3 The Down button (Dec/-) - Short press to change/decrease parameter value at the menu setting interface.
PAGE 13
Image Parameter While the monitor is showing the rear image, short press the middle button (Menu/OK) to enter the main menu interface. From the 5 options select “Image Parameter”, long press the (Menu/OK) button again, 3 Images (Brightness/ Contrast/ Colour) setting interface are shown below: Brightness Select Brightness icon, press (Add/+) or (Dec/-) button to adjust the brightness. Contrast Select Contrast icon, press (Add/+) or (Dec/-) button to adjust the contrast.
PAGE 14
Parking guidelines Display or no display: While the monitor is showing the rear image short press Down button (Dec/-) to switch the Parking guide Lines display modes (Display or No display)! Position Adjustment: The parking guideline position can be adjusted up or down, to mark the image area more realistic. There are 5 levels for choice. While the monitor is showing the rear image, short press the middle button (Menu/OK) to enter the main menu interface.
PAGE 15
monitored responsibly by trained personnel. ⚫ The seller assumes no responsibility for damage that occurs during the use of the device, as well as for complaints by third parties. Environmental conditions ⚫ Avoid heavy mechanical stress on the device. Protect it from vibration, hard knocks, do not drop it or shake it. ⚫ Do not expose the device to high temperatures (over 60°C) and strong temperature fluctuations. Protect it from direct solar radiation and proximity to radiators.
PAGE 16
Disposal Waste electrical equipment from private households ⚫ If you no longer have any use for the device, hand it in free of charge at a public collection point designated for old electrical devices. ⚫ Under no circumstances should old electrical equipment be disposed of in the residual waste. Further notes on disposal ⚫ Always return the old electrical equipment in such a way that its subsequent reuse or recycling is not impaired.